Page 1
Installation and operating instructions KITCHEN WITH OVEN FOR PROFESSIONAL USE TPT-64G TP4T-610G TPF4-610G TPF4-610GEM TPFM4-610GEM Model LIBR.ISTR.TP60GNEW Code 563014600 Review 1 Edition date 05/09/2019 Language English LOTUS S.p.A. Via Calmaor, 46 31020 San Vendemiano +39 0438 778020 +39 0438 778277...
INTRODUCTION Components FIG. A Translation of the original instructions...
Page 6
INTRODUCTION FIG. B 1 Gas ring cover 2 Injector 3 Air adjustment 4 Knob 5 By-pass 6 Gas tap 7 Gas ramp 8 Power button FIG. C 1 By-pass Translation of the original instructions...
Page 7
INTRODUCTION FIG. D 1 By-pass FIG. E Air adjustment Translation of the original instructions...
Page 8
INTRODUCTION FIG. F 1 Ignition spark plug 2 Injector 3 Extends drainage 4 Air adjustment Translation of the original instructions...
Page 9
INTRODUCTION FIG. G Translation of the original instructions...
Page 10
INTRODUCTION FIG. I 1 Injector 2 Pilot Translation of the original instructions...
Page 11
INTRODUCTION TOP WIRING DIAGRAM 1 Power supply terminal board 2 Push-button starting burner 3-4 Burner ignition control unit Translation of the original instructions...
Page 12
INTRODUCTION STATIC ELECTRIC OVEN WIRING DIAGRAM (D) 1 Switch 2 Oven lamp 3 Power supply terminal board 4 RS Upper resistor 4 RG Grill resistor 4 RI Lower resistor 5 White indicator light 6 Green indicator light 7 Timer 8 Thermostat Translation of the original instructions...
Page 13
INTRODUCTION WIRING DIAGRAM MULTIFUNCTION ELECTRIC OVEN (E) 1 Switch 2 Oven lamp 3 Power supply terminal board 4 Motor fan 5 RS Upper resistor 5 RG Grill resistor 5 RI Lower resistor 5 RC Circular resistance 6 White indicator light 7 Green indicator light 8 Timer 9 Thermostat...
Page 14
INTRODUCTION STATIC GAS OVEN WIRING DIAGRAM 1 Switch 2 Oven lamp 3 Power supply terminal board Translation of the original instructions...
GENERAL INFORMATION 2 GENERAL INFORMATION Declaration of compliance The manufacturer declares that the appliances comply with the requirements of the regulation GAR 2016/426 for the gas part and directive 2014/30/EU,2014/35/EU for the electrical part. Installation must be performed in compliance with current regulations, especially with regard to ventilation of the premises and the exhaust gas evacuation system.
INSTALLATION 3 INSTALLATION Delivery checks On delivery, it is important to check the following: · External conditions of the packaging · The general status of the equipment · The conformity of the model with the information in the technical data plate and the instruction manual ·...
Page 18
INSTALLATION Warning Installation operations, any conversion to other types of gas and start-up must only be performed by qualified personnel, in accordance with current regulations. Gas systems, electrical connections and premises where the appliances are installed must comply with current regulations in the country of installation;...
Page 19
INSTALLATION valve and fast-closing valve. Once installation is complete, make sure that there are no gas leaks from the fittings; to do this, do not use a naked flame but substances that do not cause corrosion, such as solutions of soapy water or leak detectors.
Page 20
INSTALLATION - "A" type devices (see data plate) "A" type appliances must discharge combustion products into appropriate hoods, or similar devices, connected to an efficient fume stack or directly to the outside. (Natural evacuation) Fig. 1 If this is not possible, using an air suction device connected directly to the outside is permitted (Forced Evacuation) Fig.2, having a flow capacity not lower than the value defined in point 4.3 of the UNI-CIG 8723 standard.
Page 21
INSTALLATION 1 Windproof fume stack (fig.3) - Extractor hood (fig.4) 2 Servo system "B11" type appliances are supplied on request with a hood or a hood and windproof fume stack to be assembled and delivered separately. Translation of the original instructions...
INSTRUCTIONS FOR USE 5 INSTRUCTIONS FOR USE General information This appliance must only be used for its expressly intended purpose for cooking or heating food. Any other use is considered improper. The appliance is also intended for industrial use and must only be used by personnel trained for use and aware of the risks that the hot element entails.
INSTRUCTIONS FOR USE To ignite, turn the knob to the left from position "0" into any position between and 250 °C; Hold the down pressed until the gas ignites. The flame can be checked through the inspection hole on the bottom of the oven release the knob after a few seconds.
INSTRUCTIONS FOR USE Turn the oven control knob to the symbol Oven lighting To switch the oven lamp ON, press the button with the symbol . This means you can check food while it is cooking through the glass without opening the door. ...
Page 26
INSTRUCTIONS FOR USE Grill heating element Grill heating element and ventilation Lower, upper heating element and ventilation Circular heating element and ventilation Ventilation The green pilot light comes ON, indicating that the oven is powered up. After selecting the type of cooking, turn the timer knob to the left into the manual position ("hand"...
INSTRUCTIONS FOR USE 5.10 Cooking table for the fan oven Ventilated electrical oven cooking table Guide no. Temperature Min. cooking Type of food from the Quantity Kg °C time bottom Sweets With a beaten dough, in a mould With a beaten dough, without a mould 1-3-4 Shortcrust pastry, cake base 1-3-4...
INSTRUCTIONS FOR USE Note · The indication of use of the levels shown in the table is recommended when cooking on multiple levels · The indicated times refer to cooking on only one level. Add 5-10’ when cooking on multiple levels ·...
MAINTENANCE 6 MAINTENANCE Routine When using the appliance over time, it is essential to perform regular maintenance to ensure safe operation. We therefore recommend stipulating a service contract. Caution Maintenance must only be performed by specialist personnel in compliance with current ...
MAINTENANCE Replacing the grill burner nozzle To replace the nozzle, unscrew the securing screws (see fig. F), move the burner to the right and release it, unscrew the nozzle (2) using a suitable wrench and replace it (see "Technical data" table). Set the air adjustment bush (4) to the corresponding value in the "technical data"...
Page 31
MAINTENANCE · HEATING ELEMENTS; open the oven door and remove the wires connecting the heating element. Unscrew the supports that fasten the oven to the enclosure and then replace it Caution WHAT TO DO IN THE EVENT OF FAULTS: ...
CLEANING 7 CLEANING Routine cleaning Caution The use of flammable fluids to clean the appliance is forbidden To ensure hygiene and the durability of the appliance, perform external cleaning on a regular basis, taking care not to damage the cables and the electrical connections. Before starting cleaning, disconnect the appliance from the power supply.