Advertisement
Quick Links
This manual contains important safety and operation instructions for correct use of the battery charger.
Read through the manual and pay special attention to the markings and labels of the charger,
Pay special attention to these two types of notices used in this manual.
Failure to heed this warning may cause injury to persons and damage to Equipment.
Failure to observe this warning may result in damage to equipment
WARNING:
●
The charger is not designed for any life saving application.
●
The charger is designed for in-door use. Protect the charger from ingress of water.
●
This charger is made to charge only properly sized lead acid batteries and LiFePO
●
Don't recharging non-rechargeable batteries.
●
Charging other types of battery or under-sized lead acid batteries may cause fire or explosion.
●
Install the charger in accordance with all local codes.
●
Do not use the charger if it has been dropped or damaged.
●
Never attempt to charge a frozen LEAD BASED battery.
●
Never attempt to charge LiFePO
●
Never attempt to charge LiFePO
●
Never attempt to charge a damaged battery.
●
Wear protective goggles and turn your face away when connecting or disconnecting the battery.
●
Never place the charger on top of a battery.
●
Never smoke, use an open flame, or create sparks near battery or charger during normal charging
operation as batteries may give out explosive gas.
●
Do not charge batteries in an enclosure (box- in) due to possible explosion of entrapped explosive gas.
●
If the charger does not work properly or if it has been damaged, unplug all DC connections.
Copy Right
All rights reserved.
No part of this publication may be reproduced, or transmitted in any form or by any means without the written
permission from Manson Engineering Industrial Ltd.
Changes in the manual.
Manson Engineering Industrial Ltd. has the right to update and change the content of this manual without
any prior notice and obligation.
SBC-6104/ 6106/ 6111
12V-12V In-Car Charger
Operation manual
Keep this manual in a safe place for quick reference at all times.
battery and equipment connected to the battery system.
and improper functioning of the Charger.
battery below minus 5°C.
4
battery without build-in BMS (Battery Management System)
4
(LFP).
4
Advertisement
Related Manuals for Manson Engineering Industrial SBC-6104
Summary of Contents for Manson Engineering Industrial SBC-6104
- Page 1 No part of this publication may be reproduced, or transmitted in any form or by any means without the written permission from Manson Engineering Industrial Ltd. Changes in the manual. Manson Engineering Industrial Ltd. has the right to update and change the content of this manual without any prior notice and obligation.
- Page 2 Disclaimer Exclusions for documentation, Indemnity and Product application. Manson Engineering Industrial Ltd. (Manson) Assumes no warranty to the accuracy, suitability of technical information given in the user manuals or other documentation. Undertakes no responsibility or liability of losses, damages and related expenses whether specific, direct, indirect consequential or accidental which might result from the use of information given in this manual.
- Page 3 : Only for 12V Input (starter) battery this charger has reverse current charging at around 17A for SBC-6104, 20A for SBC-6106 and 40A for SBC-6111 under the following conditions. And this feature can be selected to ON or OFF by Select Button.
- Page 4 Features ● Power conversion efficiency > 92%. ● 6 selective charging profiles suitable for charging for the most lead acid & Lithium (LiFePO4) batteries. ● Supplied with a remote Battery temperature sensor to ensure precise and safe charging in large temperature variation.
- Page 5 Fig. 1: correct installation direction Indicators and Controls Fig. 2: 7 LED display Select Button The Select Button is for selection of battery, deactivate Ignition Control Mode, turn ON/ OFF the reverse charging feature and Manual Override feature. ● Long press the Select Button for 5 seconds for battery selection. ●...
- Page 6 Stop at the chosen battery type and wait till LED stops flashing to confirm your selection. Connections After both input and output are connected, the charger will have output after 10 Sec. SBC-6111 SBC-6104/ 6106 Fig 3.: Terminals Vin: Input positive (Ve+) terminal.
-
Page 7: Charge Mode
≤12.2V +/- 0.2V Vibration Sensor & Ignition Feed Inactive Input and output fuse Please use the following value for recommended external input (FUSE 1) and output (FUSE 2) fuses Recommended FUSE rating SBC-6104 SBC-6106 SBC-6111 FUSE 1 125A FUSE 2 125A... - Page 8 Specification Models SBC-6104 SBC-6106 SBC-6111 Rated Output power 38A at 13.8VDC 60A at 13.8VDC 110A at 13.8VDC Efficiency ≥92% Input DC Input Voltage Range 11 – 16VDC No load input current <20mA Output (Charge) Voltage Battery Type Lead Absorption 14.4V Float 13.3V...