Advertisement
System connections
@ FM DE-EMPHASIS
switch (Except some
areas) switch (Except for some areas)
This switch has been set to the correct position for a given
market area. However, check to see that this switch is set
correctly before operating your unit. An incorrect setting
will adversely affect high-frequency performance.
Europe and OC@aMia oi... eceeeeeeeseceeesessseeteeceetenees 50 us
Other COUNTIES ives. chi sdesssescatidetevesleectesteinesssecdecveeccbeice 75 ps
Note:
When
changing the setting of the AM/FM
CHANNEL
SPACE
switch, first unplug the AC power cord, then operate the switch,
and finally insert the AC power cord again.
@ AC outlets (KT-2010)
The AC outlets on the rear panel can be used to supply
power to other components in the system. Never connect
equipment whose power consumption exceeds the max-
imum value shown at each outlet.
SWITCHED:
This outlet supplies power when the unit is
set to tuner mode or the built-in timer is activated.
UNSWITCHED:
This outlet provides power when the unit
is plugged into an active AC wall outlet. regardless of
the setting of the POWER switch of timer.
AC outlet (KT-2010L)
SWITCHED:
This outlet supplies power when the unit is
set to tuner mode or the built-in timer is activated.
SWITCHED outlet
100 W
400 W
UNSWITCHED outlet
700 W
@ Output
Signals from the output jacks are fed to the amplifier.
Connection cables should be plugged into the amplifier
TUNER or AUX jacks. Shielded cables terminated at both
ends with audio cords are supplied with this tuner.
@ Ground
For maximum
safety and minimum
interference connect
the GND terminal to a good earth ground if practicable.
A good earth ground is a metal stake driven into moist
earth.
POWER
key standby
A small amount
of current
is used
to support
the
memory when POWER is switched OFF. This is known
as standby mode.
8
KT-2010/KT-2010L (En)
@ AM/FM
CHANNEL
SPACE
switch
(Ex-
cept some areas)
The CHANNEL SPACE switch on the rear panel is set to
the correct setting that prevails in the area to which the
unit is shipped. However, if the channel space setting is
not matched to the area where the unit is to be used;for
instance, when you moved from area 1 to area 2 or vice
versa,
desired
reception
of AM/FM
broadcasts
is not
expected.
In this case, change
the CHANNEL
SPACE
setting in accordance with the area corresponding to the
table shown below.
Channel Space Frq.
1. U.S.A., Canada
FM:
100 kHz
Hawaii, and Guam
AM:
10 kHz
FM:
2. European countries
50 kHz
Far East countries
AM:
9 kHz
Channel space table
@ Before plugging the power plug into an
AC outlet
Set the STATION
NAME AND PRESET select switch on
the rear panel of this unit to either the 12"
or the "20"
position according to the the number of stations you want
to preset. After setting this switch, plug the power cord
into the AC outlet. (For presetting operation. refer to page
13, and for tuning to preset stations, refer to page 12.)
When station name
display is required
display is not required
Switch on the rear panel
(Set to "12")
(Set to "20")
STATION NAME
STATION NAME
AND
AND
PRESET 12
PRESET 12
<>
<>
PRESET 20
]
PRESET 20
]
(This switch
is set to "12"
when the unit is shipped.)
® A total of 12 FM or AM | @A
total of 20 FM or AM
stations can
be preset
stations can
be preset
for channels A and B.
for channels A and B.
@ Usable keys are as fol- | © Usable keys are as fol-
lows:
lows:
Channel A:
1-6
Channel A: 1-0
(A-1 to A-6)
(A-1 to A-0)
Channel B: 1-6
Channel B: 1-0
(B-1 to B-6)
(B-1 to B-0)
Advertisement
