Panasonic WX-C1011 Series Operating Instructions Manual page 6

(D Power Indicator (POWER)
This indicates that the center module is fully power-ed.
@) Vehicle Detector Indicator LED (VEHICLE
PRESENT)(Amber)
This indicates that a vehicle has been detected.
(9 Power On/Otf Switch (POWER, ON/OFF)
This switch turns the power on and off to the center
module.
(4) Vehicle Detector On/Over-ride On/Off Switch
(VEHICLE DETECTOR NORMAL, OVERRIDE ON,
OFF)
NORMAL: Set the switch to the NORMAL position
when a vehicle is at the menuboard.
A beep tone is heard on the Order Taker headset.
After the beep tone, the Menuboard Speaker turns
on allowing communication to and from the cus-
tomer. When the vehicle leaves, the Vehicle
Detector turns off.
OVERRIDE ON: Set the switch to OVERRIDE ON posi-
tion.
The Vehicie Detector is always turned on.
OFF: Set the switch to the OFF position.
A vehicie at the Menuboard is not detected.
No beep tone is heard in Order Taker headset and
the Menuboard Speaker remains off.
(5) Order Taker Talk Lock Release Switch (O/TAKER
TALK LOCK RELEASE)
This switch is used to release temporarily the Order
Taker Talk Lock mode.
(6) Talk/Page Indicator (TALK/PAGE MONITOR)
Red: When the Order Такег 6 in the Talk mode, the
indicator lights red.
Green: When the Order Taker is in the Page mode, the
indicator lights green.
(7) Auxiliary Input Level Control (AUX INPUT VOLUME)
This controls the input level to the Auxiliary Input
Terminal (31).
Vehicle Detector Beep Volume Contro! (BEEP,
VOLUME)
This control seis the vehicle detect alert beep tone for
the Order Taker to the optimum level.
Caution: When the Vehicle Detector On/Override
On/Off Switch (4) is set to NORMAL position, the
beep tone level of the Remote Speaker is also var-
ied by turning this control.
(8 Remote Speaker Control (REMOTE SP VOLUME)
This control sets the output level of the Remote
Speaker to the optimum level.
Note: The line marked on this control is a standard
position for this adjustment.
Adjust this control to the suitable position so that
feedback does not occur.
: Noise
i ound
} i Reduction | 299
"Жыш; von ou ality
| fè ki i jl
| [| I] и [=
19 Inbound Volume Control (INBOUND VOLUME)
This control sets the sound level from the Menuboard
Microphone to the optimum level.
Caution: Adjust this control after setting the Vehicle
Detector On/Override On/Off Switch (4) to OVER-
RIDE ON position and the Vehicle Detector
Indicator lights.
Note: The line marked on this contro! is a standard
position for this adjustment.
Adjust this control to the suitable position so that
feedback does not occur.
17 Outbound Volume Control (OUTBOUND VOLUME)
This control sets the output level of the Menuboard
Speaker to the optimum level for talking to customer.
Caution: Adjust this control after setting the Vehicle
Detector On/Override On/Off Switch (4) to OVER-
RIDE ON position and the Vehicle Detector .
Indicator lights.
Note: The line marked on this contro! is a standard
position for this adjustment.
Adjust this control to the suitable position so that
feedback does not occur.
* The following switches and terminals should be
used by qualified service personnel only.
* To change the setting of the following switches,
turn off the power of the center module, then turn it
back on.
O——————————————————————————————————— 1 —-
i (2 Circuit Protector (CIRCUIT PROTECTOR) i
| If excessive current flows to the Center Module, the |
Circuit Protector is triggered. Turn off the Power |
On/Off Switch (3) first, push in on the red circuit pro- :
tector and turn on the Power On/Off Switch (3) again. |
If the circuit protector is soon triggered again, con- |
sult your dealer or authorized service center for ;
assistance. |
| (3 DNR (Digital Noise Reduction) Effect Level
: (DNR EFFECT DNR1, DNR2, DNR3, ON/OFF) |
These switches are used for noise reduction level |
setting. |
The more the noise is reduced, the lower will be the |
sound quality. The table below shows the |
relationship between noise reduction level and ;
sound quality. |
No setting should be done other than shown іп the |
table. :
Remarks
fas DNR processing
For a relatively quiet
environment
DNR1 DNR2 DNR3 For a general environment.
Normal ооа This balanced setting 15
| recommended.
| Fora very noisy environ-
| | ment. Not so recommen-
LOW | ded because it seriously
affects sound quality.
DNR1 ОМА2 ОМАЗ