Sony LBT-N355 Operating Instructions Manual page 19

SYSTEM
POWER>ON
OUI! OO
1 Following the procedure "Playing
Tracks in the Desired Order
(programme play)", programme the
tracks you want to record for side A.
Make sure to programme the tracks so
that the total playing time of the side A
does not exceed the tape length of one
side.
2 Press 00 on the remote to pause
recording at the end of the side A.
"P" appears in the display.
The total playing time "0.00" is
displayed.
3 Programme the tracks you want to
record for side B in the same way as vou
did for side A.
4 Press & EJECT and insert a blank tape
into deck B with the side you want to
record on facing forward.
Recording will start from the front side
of the tape, unless you have changed the
playing direction before recording.
Make sure the tabs on the cassette have
not been removed.
5 select dual or single-sided recording.
To record
to select
One side of the tape ==>
Both sides*
* Recording always stops at the end of the
reverse side. Be sure to start from the
front side.
Press DIRECTION
c=) or RELAY
6 when you want to reduce the hiss noise
in low-level high-frequency signals,
press DOLBY NR so that "DOLBY NR
B" appears in the display.
7 Press CD SYNCHRO.
The REC and 0 (pause) lamps light up
and deck B stands by for recording.
The > lamp lights up and the <J lamp
flashes for a few seconds, then
disappears.
Dee
= | oy
If you want to start recording from the
reverse side, press <1] so that the <I)
lamp lights steadily.
Side in recording
pause mode
8 Press 10 on the tape player to release
recording pause.
Recording starts.
After 10 seconds, the CD player starts
playing.
To stop recording
Press C1 on the tape player.
To check the order
Press CHECK on the remote repeatedly.
Each time you press CHECK, the number
of the programmed tracks appear in the
display.
To cancel programme edit
Press CONTINUE on the CD player.
PSs Be
Recording from the
Radio
You can record from the tuner onto a tape.
Tloa TYPE T fnormal) or TYPE TIC)
use 2 irea~a normay OF iirc is (Wz;
tapes.
SYSTEM
POWER?ON 2
1 Press & EJECT and insert a blank tape
into deck B with the side you want to
record on facing forward.
Recording starts from the front side of
the tape, unless you change the playing
direction before recording.
Make sure the tabs on the cassette have
not been removed.
2 Press TUNER/BAND several times
until the desired radio band appears.
3 Tune in the radio station you want to
record. (See "Listening to the Radio", or
"Playing Preset Radio Stations" for
details.)
4 select dual or single-sided recording.
To record
to select
—
One side of the tape ==
Both sides*
* Recording always stops at the end of the
reverse side. Be sure to start from the
front side.
5 when you want to reduce the hiss noise
in low-level high-frequency signals,
press DOLBY NR so that "DOLBY NR
B" appears in the display.
6 Press REC.
The REC and 00 (pause) lamps light up
and deck B stands by for recording.
The C> lamp lights and the <I lamp
flashes for a few seconds, then
disappears.
f Ad
If you want to start recording from the
reverse side, press <J so that the <I
lamn Hohte ctaadily
JaiTip sigris Sreaauy.
Side in recording
pause mode
7 Press 00 on the tape player to release
recording pause.
Recording starts.
To stop recording
Press C on the tape player.
To reduce noise during MW/LW (AM)
recording
If a whistling noise is heard while
recording, reorient the AM loop aerial for
optimum reception.
Chapter 4: the Tape Player
Press DIRECTION
c=) or RELAY