Page 1
TECHNICAL MANUAL STATIONARY RACK POT, PAN UTENSIL WASHING MACHINES SW-14-F Installation, Operation and Maintenance Instructions Insinger Machine Company 6245 State Road Philadelphia, PA 19135-2996 800-344-4802 Fax 215-624-6966 www.insingermachine.com...
Page 2
Start-Up Date:____________________________ When referring to this equipment please have this information available. Each piece of equipment at Insinger is carefully tested before shipment for proper operation. If the need for service should arise please contact your local Authorized Insinger Service Company.
15 months from the date of shipment from Insinger or 1 year (12 months) from the date of installation or start-up that said Insinger product shall be free from defects in material and workmanship. Whichever one of the two aforestated limited warranty time periods is the shortest shall be the applicable limited warranty coverage time period.
Page 5
1998. Some states do not allow limitation on how long an implied warranty lasts so this limitation may not apply to you. Insinger is not liable for any special, indirect or consequential damages. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation nor exclusion may not apply to you.
SW14F SPECIFICATIONS OVERALL DIMENSIONS WIDTH = 36” DEPTH = 51” (53” GAS) HEIGHT = 84‐1/2” HEIGHT WITH DOOR OPEN = 106” DOOR OPENING = 32” WIDE x 30” HIGH HOT WATER SYSTEM 1/2” HOT WATER SUPPLY REQUIRED, UNION PROVIDED 140° F. WATER REQUIRED AT THE MACHINE 78 GPH AT 20 PSI (6‐1/2 GAL./CYCLE x 12 CYCLES/HR.) RINSE BOOSTER: ONE 9 kW HEATING ELEMENT IN A 9‐1/2 GAL. RINSE TANK FULL LOAD AMPS 208 VOLT 230 VOLT 460 VOLT ELECTRIC 79.0 72.2 37.1 GAS/STEAM (INJECTED) 54.0 49.6 25.8 STEAM (RECIRCULATING) 29.0 27.0 14.5 GAS SYSTEM (GAS MACHINES ONLY) ½” GAS SUPPLY NATURAL: 7” W.C. MINIMUM INLET, 6” W.C. MAIN MANIFOLD = 48,000 BTU PROPANE: 11” W.C. MINIMUM INLET, 10” W.C. MAIN MANIFOLD =48,000 BTU ...
ELECTRICAL DATA for MODELS SW‐14‐F, SW‐14‐P Electric 3phase Voltage Pump Motor 27.0 25.0 12.5 Control Circuit Wash Heater (one 9kW) 25.0 22.6 11.3 Rinse Heater (one 9kW) 25.0 22.6 11.3 Total Running Current 79.0 72.2 37.1 ELECTRICAL DATA for MODELS SW‐14‐F, SW‐14‐P Gas or Injected Steam 3phase Voltage Pump Motor 27.0 25.0 12.5 Control Circuit Rinse Heater (one 9kW)
General Warnings and Cautions Service work on the machine should be done by either a factory representative or qualified local service company. Contact the factory if the machine is under warranty. Failure to follow the cleaning guidelines described in this manual will damage the machine and will void the warranty.
Contact the factory if the machine is under warranty. The INSINGER pan washer is designed for use in bakeries, restaurants, schools, hospitals, and hotels, to clean pots, pans, bowls, and utensils. INSINGER pan washers are constructed of 14 gauge stainless steel (cabinets) and 12 gauge stainless steel (framework).
Installation Instructions Step 1 READ : Read and understand these instructions thoroughly before attempting any part of the installation procedure. WARNING: Not following these instructions may void warranty, cause damage to the equipment and/or cause injury to anyone involved in the installation or operation of this machine. A copy of the installation instructions and startup procedure is printed on the yellow sheet attached to the side of the machine.
Page 11
Step 6 STEAM VENT : The machine is equipped with a collar for 6" duct work as shown on pages 26 and 27. This duct should be directly vented to the outside of the building. DO NOT vent into a wall, attic, or any other concealed space of the building, and avoid horizontal runs of duct.
Page 12
Step 8 GAS CONNECTION (Gas models only): A certified gas technician is required for the hookup and final adjustments of the burners. This is necessary to insure proper inlet and manifold pressure for the gas machines (see page 6 for gas pressure settings). Verify the type of gas supply to be used, either natural or LP, and make sure the marking on the gas data plate agrees with that of the supply.
StartUp Procedures Warning: These instructions must be followed or damage to the machine will result. Step 1: Close the drain valve (see location on pages 25 and 33). Step 2 : Open the main water supply valve (if the machine is equipped with the Auto Fill option, skip to Step 3), then open the fill valve (see location on pages 26 and 27).
Page 14
Wait about a minute after turning the machine off before turning it back on. If the machine still does not appear to be heating up properly, call INSINGER Manufacturing. Step 9 : Adjust the pressure regulator (see location on pages 26 and 27).
Sequence of Operation Power switch "ON". LOGO logic control is energized. Fill button (optional) energizes fill solenoid. Low water safety switch closes terminals 1 and 4 in the control panel if there is sufficient water in the wash tank. Amber indicator light comes on.
Page 16
An automatic soap dispenser should be installed at the job site by the chemical supplier. There should be a visible or audible means of determining detergent delivery. If they have any questions concerning the installation of their dispenser to the INSINGER pan washer, they can call the factory for advice.
10. Replace the pump inlet screen and the scrap tray screens. 11. Close the drain and leave the machine empty of water until it is to be used again. PREVENTIVE MAINTENANCE FOR INSINGER PAN WASHERS 1. Turn off power and drain machine, making sure it drains freely.
Page 18
7. Check if rinse pressure is approximately 20 psi. Note: This must be checked during rinse cycle only for accurate reading. 8. Make sure steam exhaust fan is working properly. On machines with a 100cfm Tjernlund fan, the fan should run continuously when power switch is turned on.
Trouble Shooting Electric Machines Problem Cause Cure Machine won't run No power to machine Check building power supply Not enough water Fill machine until overflowing Door open Close door tightly Wash pressure too high Nozzles plugged Remove debris from nozzles Wash pressure too low Pump running backward See installation instructions...
Trouble Shooting Gas Machines (Same as electric model except for the following) Low wash temperature 1. Check thermostat setting.* 2. Check switches, fuses, and breakers that control the burners. 3. Check to be sure electrical power and gas supply have not been interrupted to the burners. 4.