Related Manuals for Watersnake STEALTH 54LB/48
Summary of Contents for Watersnake STEALTH 54LB/48
- Page 1 STEALTH BOW MOUNT ELECTRIC MOTOR OWNERS MANUAL STEALTH 54LB/48” (55319) STEALTH 65LB/54” (55318) Watersnake Stealth Bow Mount Motor Manual ( Ver.1)
- Page 2 Please read this manual completely before starting installation and using the electric motor. Disclaimer: The information provided in this Watersnake Motor Manual is correct at time of printing. For the most up to date information, check for the latest version on our website at: www.watersnake.com.au/pages/watersnake-user-manuals...
-
Page 3: Table Of Contents
HOW TO PAIR THE REMOTE CONTROL TO THE MOTOR .....30 REPLACING THE BATTERIES ON YOUR REMOTE CONTROL ....31 FOOT PEDAL CONTROL ( OPTIONAL ACCESSORY ) ......32 RECOMMENDATIONS ................33 MAINTENANCE ..................34 TROUBLESHOOTING ................35-36 SERVICING ...................37 SPECIFICATION CHARTS ..............38-39 SCHEMATICS AND PARTS LISTS ............40-47 OPTIONAL ACCESSORIES ..............48 www.watersnake.com.au... -
Page 4: Know Your Boat
KNOW YOUR BOAT Gunwale Starboard Stern Port Keel Gunwale Stern Hull Outboard Inboard Starboard Port Stern / Transom Watersnake Stealth Bow Mount Motor Manual ( Ver.1) -
Page 5: Features And Box Contents
FEATURES AND BOX CONTENTS Head unit Coiled data cable Multi adjustable depth collar Bracket Remote control fob x 1 3 Bladed Propeller x1 Composite shaft Propeller shear pin x 1 Propeller nut x 1 Motor Assembly Unit Propeller wrench x1 www.watersnake.com.au... -
Page 6: Pre-Installation Checklist
Watersnake motor, labelled in the illustrations. • Select desired mounting location on boat. • 12v deep cycle or LiFePO4 battery (your Watersnake motor is not designed for use with car / truck / motorcycle or marine cranking batteries) – for more information about appropriate batteries for your Watersnake motor, refer to page 17. - Page 7 Do not overtighten the screws. PLEASE NOTE: Watersnake accepts no liability for personal injury or property damage caused while fi tting this motor. Please wear appropriate protective clothing and eyewear/face protection. Avoid contacting and/or inhaling fi breglass dust or aluminium shavings.
- Page 8 BOLT HOLE POSITIONS MOUNTING PLATE BOLT HOLE POSITIONAL. There are pre threaded holes for easy installation of the optional Watersnake quick release nylon or alloy brackets. Through hole Through hole Threaded hole Threaded hole Through hole Through hole Threaded hole...
-
Page 9: Installation Direct Mount
PLEASE NOTE: Your Watersnake motor does not come supplied with any mounting hardware. Mounting hardware is only included with the optional Watersnake quick release brackets PLEASE NOTE: Watersnake accepts no liability for personal injury or property damage caused while fi... - Page 10 Check that no part of boat impedes full deployment of motor. 4. Check with the motor in a deployed position that the Watersnake shaft does not come into contact with any part of the hull. Allow at least 30mm clearance from boat gunwale.
-
Page 11: Installation With Optional Quick Release Brackets
Watersnake mount assembly, including the optional quick-release plate, must be mounted in a level, horizontal position as close to the boat’s centreline as possible. The Watersnake motor and quick-release plate do not necessarily need to face directly forward. On slightly curved decks, spacer washers or blocks must be used to ensure level mounting of the motor base and/or lower quick-release plate. - Page 12 Duralac or a similar product to prevent corrosion. (Including the threads ) Alternativly you could coat the bolts and threads with a threadlocker to help prevent corrosion and them loosening over time. Watersnake Stealth Bow Mount Motor Manual ( Ver.1)
- Page 13 PLEASE NOTE: Watersnake accepts no liability for personal injury or property damage caused while fitting this motor. Please wear appropriate protective clothing and eyewear/face protection. Avoid contacting and/or inhaling fibreglass dust or aluminium shavings.
- Page 14 Watersnake mount assembly, including the optional quick-release plate, must be mounted in a level, horizontal position as close to the boat’s centreline as possible. The Watersnake motor and quick-release plate do not necessarily need to face directly forward. On slightly curved decks, spacer washers or blocks must be used to ensure level mounting of the motor base and/or lower quick-release plate.
- Page 15 PLEASE NOTE: Watersnake accepts no liability for personal injury or property damage caused while fitting this motor. Please wear appropriate protective clothing and eyewear/face protection. Avoid contacting and/or inhaling fibreglass dust or aluminium shavings. www.watersnake.com.au...
- Page 16 INSTALLATION OPTIONAL ALLOY QUICK-RELEASE BRACKET TOP PLATE ATTACH TO YOUR MOTOR BOTTOM PLATE ATTACH TO YOUR BOAT Watersnake Stealth Bow Mount Motor Manual ( Ver.1)
-
Page 17: Battery And Power
BEST PRACTICES INSTALLING AND CONNECTING YOUR STEALTH MOTOR 1. Your Watersnake motor is designed to be powered by a 12v deep cycle or LifePO4 battery that should output no more than 14.5v. If the voltage input to your Watersnake motor exceeds 14.5v it may damage the sensitive electronics and void your warranty. -
Page 18: Extending Battery Leads
You can charge your battery via an alternator or solar system, so long as the voltage input to the Watersnake motor does not exceed 14.5v whilst the battery is being charged. If you are unsure about the voltage that your motor is receiving, consult a marine auto electrician. -
Page 19: Connecting Your Motor To The Battery
(refer to page 7 of manual) • Fully charged 12v deep cycle or LiFePO4 battery (your Watersnake motor is not designed to be used with a car / truck / motorcycle or marine cranking battery) • Check battery cable for any signs of damage or exposed wiring •... -
Page 20: Attaching The Propeller
Do not overtighten; check regularly. Shear pin Propeller nut Propeller shaft PLEASE NOTE: Propeller t is suggested that you have a spare propeller and propeller accessory kit in your boat at all times. Propeller wrench Watersnake Stealth Bow Mount Motor Manual ( Ver.1) -
Page 21: Deployment Instructions
DEPLOYING INSTRUCTIONS Failure to deploy your Watersnake as described below may damage your unit, invalidating its warranty, and could injure you and/or other people. STEP 1: Loosen the depth collar and slide it up the shaft to the desired depth. - Page 22 Slowly rotate the released motor unit into the deployed position. When you hear a click the motor is locked into place. Do not let go of the shaft during this process as you may damage the motor. Watersnake Stealth Bow Mount Motor Manual ( Ver.1)
- Page 23 30cm below the waterline to the top of the propeller, to avoid ventilation. ( Prop sucking air from surface. ) PLEASE NOTE: Watersnake Distribution Pty Ltd accepts no liability for injury or damage caused by the incorrect deployment or stowing of this motor. www.watersnake.com.au...
-
Page 24: Stowing Instructions
STOWING INSTRUCTIONS Failure to stow your Watersnake as described below may damage your unit, invalidating its warranty, and could injure you and/or other people. STEP 1: Turn off the Motor using the On /Off button on the back of the motor bracket... - Page 25 STEP 5: Loosen the depth collar on the motor shaft and slide it so that it is flush up against the turning box unit then re-tighten it. This will prevent the motor from self deploying whilst in transit. www.watersnake.com.au...
- Page 26 While storing your motor after your boating trip it is recommended to disconnect it from the battery. PLEASE NOTE: Watersnake Distribution Pty Ltd accepts no liability for injury or damage caused by the incorrect deployment or stowing of this motor. Watersnake Stealth Bow Mount Motor Manual ( Ver.1)
-
Page 27: Remote Controller
• The remote control unit is on when the remote control unit light illuminates. The remote control unit light is located at the bottom centre of the remote. • Watersnake recommends you carry spare batteries and a suitable screwdriver for the FOB on your boat at all times to ensure you have replacements in case of failure of those in the FOB unit. -
Page 28: Initial Power Up
INITIAL POWER-UP • Attach your Watersnake Stealth to a 12 volt deep cycle or LiFePO4 battery. • Deploy the motor and ensure locking lever is in the up position. NOTE: Your Watersnake motor is fi tted with a tilt switch that prevents the motor from running unless it is in the deployed (vertical) position. - Page 29 INITIAL POWER-UP • The upper LED is the unit’s Status Light. Its variable colour display signals important states of your Watersnake Stealth motor. • White Status Light: The status light fl ashes white while the motor is powering up. • Flashing Red Status Light: Motor is in stowed position and will not activate for safety reasons.
-
Page 30: How To Pair The Remote Control To The Motor
YOUR REMOTE SHOULD NOW BE CONNECTED. Test that the remote control unit controls the motor as expected. If it doesn’t turn the motor or spin the propeller, repeat steps 3 and 4. Watersnake Stealth Bow Mount Motor Manual ( Ver.1) -
Page 31: Replacing The Batteries On Your Remote Control
IMPORTANT: We strongly advise you keep a spare set of batteries ( 3 x AAA ) in your boat at all times as well as an appropriate screwdriver to open and close the remote. www.watersnake.com.au... -
Page 32: Foot Pedal Control ( Optional Accessory )
(3) is held down (adjacent red LED is lit), or constantly, without touching power button (adjacent green LED is also illuminated). (5) Variable speed control dial. Watersnake Stealth Bow Mount Motor Manual ( Ver.1) -
Page 33: Recommendations
Wipe over with a soft, dry cloth. • Store your Watersnake motor disconnected from its battery. • If boat is stored outdoors, remove Watersnake and store securely indoors in a cool, dry place. -
Page 34: Maintenance
• Remove batteries from Remote control. • Remove motor from boat and store in a cool, dry place away from temperature extremes. Cover your Watersnake motor to prevent dust and dirt buildup. • Apply Diaelectric grease to electronics. Watersnake Stealth Bow Mount Motor Manual ( Ver.1) -
Page 35: Troubleshooting
NO POWER / REDUCED POWER NOTE – Your Watersnake motor is fi tted with a tilt switch that prevents the motor from running unless it is in the deployed (vertical) position. • Check that battery connection has not been reversed (reversed polarity). - Page 36 • Check that foot control cable plug is fi rmly connected and locked in. • Check for debris that may affect operation of pedal controls and cable connections. • Check speed control dial is not set to zero • Restart base unit and recheck. Watersnake Stealth Bow Mount Motor Manual ( Ver.1)
-
Page 37: Servicing
SERVICING SERVICING YOUR WATERSNAKE ELECTRIC MOTOR When it’s time for your Watersnake electric motor to be serviced, it is recommended you choose to use an Authorised Service Agent such as Anglers’ Central Service Centre to perform the service. For Australian residents, you can fi nd up to date contact details on our website. -
Page 38: Specification Charts
* NOTE - this is to be used as a guide only. Check with your battery supplier to confi rm required size of 12 volt deep cycle or LiFePO4 battery that will be appropriate for your situation. Your Watersnake Stealth motor is fi tted with built in voltage protection, current protection and overheating temperature control. - Page 39 * NOTE - this is to be used as a guide only. Check with your battery supplier to confi rm required size of 12 volt deep cycle or LiFePO4 battery that will be appropriate for your situation. Your Watersnake Stealth motor is fi tted with built in voltage protection, current protection and overheating temperature control.
-
Page 40: Schematics And Parts Lists
SCHEMATICS AND PARTS LIST 55319 Stealth 54lb/48” Watersnake Stealth Bow Mount Motor Manual ( Ver.1) - Page 41 PART NO. 55319 Stealth 54lb/48” TO ORDER YOUR WATERSNAKE STEALTH PARTS, VISIT: www.anglerscentral.com.au PART NO. www.watersnake.com.au...
- Page 42 SCHEMATICS AND PARTS LIST 55319 Stealth 54lb/48” Watersnake Stealth Bow Mount Motor Manual ( Ver.1)
- Page 43 PART NO. 55319 Stealth 54lb/48” TO ORDER YOUR WATERSNAKE STEALTH PARTS, VISIT: www.anglerscentral.com.au www.watersnake.com.au...
- Page 44 SCHEMATICS AND PARTS LIST Watersnake Stealth Bow Mount Motor Manual ( Ver.1)
- Page 45 PART NO. TO ORDER YOUR WATERSNAKE STEALTH PARTS, VISIT: www.anglerscentral.com.au PART NO. www.watersnake.com.au...
- Page 46 SCHEMATICS AND PARTS LIST Watersnake Stealth Bow Mount Motor Manual ( Ver.1)
- Page 47 PART NO. TO ORDER YOUR WATERSNAKE STEALTH PARTS, VISIT: www.anglerscentral.com.au www.watersnake.com.au...
-
Page 48: Optional Accessories
Nylon Alloy Quick Release Quick Release Bracket 55502 Bracket 55016 3 Blade Prop Propeller 3 Blade Prop For 65LB Model Accessory Kit For 54LB Model 55535 55132 55130 Foot Control 55532 Watersnake Stealth Bow Mount Motor Manual ( Ver.1) - Page 49 THE BELOW INFORMATION IS FOR THE USA ONLY. Watersnake Limited One Year Warranty (USA) All watersnake products are covered by a one year Limited Warranty covering faults in workmanship and materials from the date of original retail purchase. The purchaser shoud return...
- Page 50 NOTES: Watersnake Stealth Bow Mount Motor Manual ( Ver.1)
- Page 51 NOTES: www.watersnake.com.au...
- Page 52 297-305 South Gippsland Highway Dandenong South, Victoria 3175 Australia ACN: 143 230 175 Watersnake and Jarvis Marine are registered ® ® trademarks of Watersnake Distribution Pty. Ltd. © Watersnake Distribution Pty. Ltd. All Rights Reserved. Specifications are subject to change without notice.