Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Watersnake Hawser 54/48
Summary of Contents for Watersnake Hawser 54/48
- Page 1 HAWSER BOW MOUNT CABLE STEER ELECTRIC MOTOR OWNERS MANUAL...
- Page 2 80 - 100 AMP HOUR ** ** NOTE - this is to be used as a guide only. Check with your battery supplier to confi rm required size of 12 volt deep cycle marine battery that will be appropriate for your situation. Watersnake...
- Page 3 HAWSER Illuminated directional arrow LED Power meter Head unit Break away scissor bracket Depth adjustment collar Foot control unit Composite shaft Motor Assembly unit www.watersnake.com.au...
-
Page 4: Pre-Installation Checklist
Watersnake motor • Select desired mounting location on boat • 12 v deep cycle marine battery (your Watersnake motor is not designed for use with car / truck / motorcycle type batteries) – for more information about appropriate batteries for your Watersnake motor, refer to page 9 •... - Page 5 WATERSNAKE ELECTRIC MOTORS Congratulations and welcome to a world of silent motoring. Powerful yet silent, the Watersnake electric motors are built to suit all angling conditions. High quality materials, superior design and precision engineering make these motors longwearing and reliable.
- Page 6 IMPORTANT PLEASE READ BEFORE USE. HOW TO STOW AND DEPLOY YOUR WATERSNAKE BOW MOUNT ELECTRIC MOTOR. DEPLOYING AND STOWING YOUR MOTOR It is important that you exercise caution when deploying or stowing your Hawser motor. Always use the supplied trolling motor release rope with handle to deploy or stow your motor.
- Page 7 2: Align the propeller against the shear pin on the shaft (there is a groove on the back of the propeller which the shear pin needs to slot into) and then tighten the propeller nut securely. Shear Pin Propeller Propeller Shaft Propeller www.watersnake.com.au...
-
Page 8: Electrical Connections
50 amps. Anderson plugs are a popular choice amongst many Watersnake motor owners and are readily available. A Watersnake circuit breaker is supplied and attached to the red power cable to protect the electrics of the motor. This is a connection that joins the motor battery cable to the battery and shuts the motor off if the connection over heats. -
Page 9: Deep Cycle Batteries
DEEP CYCLE BATTERIES A 12 v deep cycle marine battery is required for normal operation and continued use of your Watersnake motor. 12 v deep cycle marine batteries are constructed using thicker plates and a denser active material. They are built to withstand repeated charge and recharge cycles. -
Page 10: Operating The Motor
When the momentary switch is pressed the motor will activate and reach the preset speed that you have set with the variable speed control. When the momentary switch is released the motor will stop. Momentary Switch Variable Speed Control Pedal Direction Control 3 Position Power Switch Watersnake... -
Page 11: Steering The Motor
( counter clockwise ). When the foot control is completely depressed backward the motor will swivel completely around and cause the boat to move in reverse. FOOT CONTROL FOOT CONTROL FOOT CONTROL HEEL DOWN LEVEL TOE DOWN LEFT TURN STRAIGHT RIGHT TURN www.watersnake.com.au... -
Page 12: Maintenance
MAINTENANCE Your Watersnake Electric Motor should provide many seasons of dependable service. However, like any tool, electric motors must be cared for. After each day of fi shing, the motor should be cleaned thoroughly. A light rinse with fresh water (do not direct a high pressure stream of water at the motor) and wash with warm soapy water to remove any remaining salt / debris particles should be completed. - Page 13 If your boat is not stored under cover, it is recommended to remove your Watersnake motor and store separately under cover, out of direct sunlight and away from wet or damp areas. If you are not able to remove your Watersnake from the boat, we recommend covering your Watersnake with a weatherproof cover to protect the electronics.
- Page 14 A signifi cant number of issues can be caused by a disruption of power supplied to your Watersnake motor. Careful inspection of your 12v deep cycle battery, wiring and fuse / circuit breaker set up should be completed before assuming that there is a fault with your motor.
- Page 15 • Clean any debris from the mounting bracket A number of service videos are available on the Jarvis Walker Brands Youtube channel – search “Jarvis Walker Brands” from the Youtube search function. Please contact Jarvis Walker or your nearest service agent should issues persist. www.watersnake.com.au...
-
Page 16: Model Specifications
SHAFT COLOUR BRACKET STEERING SPEEDS PROP 55149 Hawser TS54/48 54lb 13-54 156-640 1370 48" Black Scissor Foot Control Variable 3-Blade Model range and specifications are correct at time of printing. For new models not listed here find specifications at: www.jarvismarine.com.au Watersnake... - Page 17 HAWSER MOTOR SELECTION GUIDE WATERSNAKE Transom Mount Suggested Transom Mount Measurement SHAFT LENGTH to Water Level Shaft Length GUIDE Up to 8” 24” Up to 10” 26” With your boat in the Up to 12” 30” water, measure the 10” to 14”...
- Page 18 SERVICING YOUR WATERSNAKE ELECTRIC MOTOR When it’s time for your Watersnake electric motor to be serviced, it is recommended you choose to use an Authorised Service Agent such as Anglers’ Central Service Centre to perform the service. Watersnake electric motors are precision instruments that rely on exacting alignment of numerous components;...
- Page 19 HAWSER TS 54/48 UPPER SHAFT AND HEAD UNIT. SEE PAGE 21 FOR PARTS NAME LIST. www.watersnake.com.au...
- Page 20 HAWSER TS 54/48 LOWER SHAFT AND MOTOR UNIT. SEE PAGE 21 FOR PARTS NAME LIST. Watersnake...
- Page 21 HAWSER TS 54/48 FOOT CONTROL UNIT. www.watersnake.com.au...
- Page 22 HAWSER TS 54/48 SCISSOR BRACKET Watersnake...
- Page 23 Watersnake Propeller Kits (Sold Separately) Watersnake Propeller kits contain a propeller, nut and shear pins. It is recommended you keep a spare propeller on your boat at all times. The Mini 2- Bladed Kit is suitable for the T-18 and T-24 motors. The 2-Bladed Propeller Kit is suitable for 28lb, 30lb and 34lb motors.
- Page 24 +0303 798 744 Watersnake and Jarvis Marine are registered ® ® trademarks of Watersnake Distribution Pty. Ltd. United Kingdom Masterline Walker +44 0 1684 299 000 © Watersnake Distribution Pty. Ltd. All Rights Reserved. Specifications are subject to change without notice.