Table of Contents
Advertisement
@ During dubbing, a source other than TAPE or DAT can be
listened to by changing the setting of the input selector
switch.
How to do DAT Digital Recording
When DAT digital input/output is connected
to this unit, DAT digitai
recording can be done if the digital signat is directly input to DAT.
4, Set the input selector switch
[7]in the DIGITAL position.
2. Set the digital recording source selector switch [10} in the ON
position.
3. Set the digital input selector switch [6] in the desired position.
(When the unit being recorded from is connected to the DIGI-
TAL-1 jack, set the digital input selector switch [Blin the Dt-
GITAL-1 position, and when the unit is connected to the DI-
GITAL-3 jack, select OKGITAL-3.}
. Begin DAT recording operation.
| . Begin program source performance.
+ Be careful'not to change the input selector switch, digital input
selector switch, or digital recording source selector switch while
recording.
op
NOTE:
Digital recording can be done only by connecting the recording
source units with the DIGITAL-1 or DIGITAL-3. Also, it is not
possible to record digitally from CD players. For more details,
please refer to the DAT operations manual.
Use the PROCESSOR jacks for simultaneous monitoring
of recording done with
a 3-head type tape deck.
(See il-
lustration for connections.)
TAPE DECK
. Set the source direct switch in the OFF (==) position:
. Set the processor on/off switch in the ON ( =) position.
. Select the source with the input selector or digital input selector.
. Begin tape deck recording operation.
. Begin program source performance.
. Simultaneous monitoring of a recording is possible by setting
the tape nionitor switch on the tape deck to the TAPE position.
© Be careful not to change the source direct switch, processor
on/off switch and input selector switch while recording.
© Simultaneous monitoring of a recording is not possible with a
2-head tape deck or a DAT, but connection is possible. Do not
connect both audio and digital output at the same time, as this
may cause vibration.
Sarena
Recording from Units Connected to the CDV Jack onto
Video Tape Recorders
4. Set the video mode switch in the VCR REC-CDV position. The
jack to which the sound of the CDV player is connected should
be selected with the input selector switch
[7] (CD, DIGITAL-1,
DIGITAL-2, DIGITAL-3, etc). Be careful not to change the input
selector switch while recording.
2. Begin video cassette recorder recording operations.
3.
Start the CDV
player.
VDP to VCR Recording
1. Select the VCR REC-VDP position on the video mode switch.
2. Start the VCR unit, in the recording mode, connected to the
VCR jacks.
3. Then start recording by activating the video component com-
nected to the VDP jacks.
© To monitor the video program being recorded, on the matitor
'TV set, set the input selector switch in the VCR or VDP postion.
if you want to listen to an audio program while recording avtdeo
program, select the desired source by simply setting the int>ut
selector switch in the corresponding source.
BGV PLAYBACK
(Background Video)
With this unit, you can play back programs on a monitor from a
video component connected to the VDP or VCR jacks while playing
your turntable, tuner, CD or tape decks.
in this example, you can play back a video program on a mo
by selecting the VCR REC-CDV or VDP video mode switc!
while listening to the CD player.
1. Select the desired audio component with the input selector
switch
[ 7 ] .
2. Select the desired video component by adjusting the video mode
switch [12] to either the BGV-VCR, VDP or CDV position.
NOTES:
© When the video mode switch is set on VCR REC-VDP or
VCR REC-CDV, the video signal from the VCR is sent to the
monitor regardless of the input selector switch position[Z].
therefore the playback signal
of VCR is not interrupted even
if the input selector switch
is turned to the VDP position.
© If there is no display from the VDP or CDV on the monitor
in these positions, be sure that both input and output leads
are correctly connected between the video components and
amplifier, all components are turned on and the VCR is not
in playback mode. More importently, make sure that your
VCR is capable of sending out an input signal.
Using a Mixing
Console
or Graphic
Equalizer
Connect this unit's PROCESSOR OUT jack with the graphic
'equalizer's (INPUT jack, and this unit's PROCESSOR IN jack with
the graphic equalizer's OUTPUT jack.
A.G10
Graphic Equalizer
or
AudioProcessar
INPUT OUTPUT
Equalizing Audio and Video Source Performance
Select the desired listening source with the input selector switch
fa.
2. Set the source direct switch
[3] in the OFF( =) position.
3. Set the processor on/off switch in the ON (==) position.
4.
.
. Begin performance.
At this time, tone control, muting, mode, and balance functions
can be adjusted from this unit.
NOTE:
When
recording something that has been sent through an
equalizer, use an equalizer which is equipped with equalizing
recording capacity.
Advertisement
Table of Contents
