Table of Contents
Advertisement
Thank you for purchasing our 4x2 Garden Chalet.
Please take the time to identify all the parts prior to assembly.
Parts List
A. - Floor Section
Floor
1 - Floor Panel - 19 1/2 x 42"
B. - Wall Section
Main Wall Panels
2
- Rear Walls - 19 1/2" x 61 3/8"
2 - Side Walls - 19 1/2" x 67" - Angled
4 - Bottom Wall Plates - 1 1/2" x 1 1/2" x 19 1/2"
Header/Jambs/Wall Extenders
2 - Door Jambs - 1 1/2" x 1 1/2" x 58 7/8"
1 - Door Header - 1 1/2" x 2 1/2" x 39"
1 - Wall Extender - 6 5/8" x 39"
1 - Low End Top Plate - 1 1/2" x 1 1/2" x 39"
Shelves
2 - Support Cleats - 1 1/2" x 1 1/2" x 22 1/2"
4 - Shelf Support - 1 1/2" x 1 1/2" x 20 1/2" - Angled
2 - Storage Shelves - 16 3/8" x 22 1/2"
C. - Roof Section
Cedar Roof
1 - Cedar Roof Panel - 23" x 46"
D. - Trim / Misc. Section
Skirting Trim
2 - Front/Rear Skirting - 1/2" x 2 1/2" x 43"
2 - Side Skirting - 1/2" x 2 1/2" x 19 1/2"
Filler Trims
2 - Horizontal Filler Trim - 5/8" x 1 1/2" x 39"
6 - Filler Trim - 5/8" x 1 1/2" x 31 3/8"
2 - High Side Filler Trim - 5/8" x 1 1/2" x 35 3/8"
Note: Trim and Skirting pieces are graded with the best face being rough sawn.
Outdoor Living Today
Steps
1
2 - 8
9 - 15
16 - 19
20 - 21
23
24 - 27
Rough sawn cedar is much easier to paint and stain.
www.outdoorlivingtoday.com
D. - Trim / Misc. Section Cont.
Outer Wall Trim and Facia
1 - Metal Drip Edge - 38"
1 - Front Horizontal Trim - 1/2" x 2 1/2" x 44 1/4"
2 - Side Fascia - 1/2" x 2 1/2" x 22 1/8" - Angle Cut Ends
1 - Rear Horizontal Trim - 1/2" x 2 1/2" x 43 1/4"
2 - Low Wide Trims - 1/2" x 3" x 62 7/8"
2 - Low Side Trims - 1/2" x 2 1/2" x 63 3/8" - Angle Cut End
2 - High Wide Trims - 1/2" x 3" x 67 1/4"
2 - High Side Trims - 1/2" x 2 1/2" x 67 1/4" - Angle Cut End
1 - High Middle Trim - 1/2" x 2 1/2" x 67 1/4"
Door System
2 - Left/Right Doors - 18 3/4" x 59 3/8"
1 - Door Flange - 1/2" x 2 1/2" x 59 3/8"
Miscellaneous
1 - Roof Ridge Cap - 1/2" x 3 1/2" x 46"
Used in Garden Chalet with High Front
1 - Above Door Trim - 1/2" x 2 1/2" x 38 1/4"
1 - Low Middle Trim - 1/2" x 2 1/2" x 62 7/8"
** Plus 2 Cedar Shingle Shims - discard after shimming
doors
Note: We recommend you drill a 1/8" pilot hole for each
screw to avoid splitting wood. The hole depth should be
equal to 3/4 the length of screw.
sales@outdoorlivingtoday.com
Page 4
Steps
28 - 34
35 - 44
45
Advertisement
Table of Contents
