Advertisement
> Playback (cont'd)
INDEX
MARK
REVIEW
EN-22
INDEX
ERASE
SHUTTLE
PLUS
bd / >>
Instant ReView
Simply by pressing a single button, the VCR power comes on,
tewinds, and begins playback of the last recording. This makes it
easier to "teview" the program you have timer-recorded.
When the VCR power is off:
{1] Press REVIEW.
~
@ After the VCR power comes on, the tape will be rewound
to the beginning of the last recording (where the index code
is placed) and playback will start automatically.
™ To play back a recording located 2 index codes away, press
REVIEW twice. You can access any one of up to 9 index
codes.
@ ReView is not possible while the VCR is in the Timer
mode.
:
@ The VCR's REVIEW button lights when timer-recording is
finished, and blinks while the tape is being rewound.
Index Search
Index codes are electronic "bookmarks" which are automatically
placed on the tape whenever recording is started. Index Search
automatically seeks out these index codes so you can easily find the
beginning of a recording (up to 9 index codes away in cither direction).
During Stop....
(1) Press SHUTTLE PLUS td or PP 4, "INDEX -1" or
"INDEX 1" will be displayed and search will begin in the
corresponding direction.
[2] If you wish to access index codes 2 through 9, press SHUTTLE
PLUS td or 9B repeatedly until the correct index number
is displayed.
@ When the specified index code is found, playback will start
automatically.
Manual! Index Mark/Erase
TO MARK AN INDEX CODE
During Playback...
(i) Press, INDEX MARK.
@ The VCR will mark an index code at that location,
@ "MARK" blinks while an index code is being marked.
TO ERASE AN INDEX CODE
r During Playback or Still...
fi] Press INDEX ERASE.
@& The VCR will fast-forward to the nearest index code and
erase it. Playback continues after the index code is erased.
L
@ "ERASE" blinks while an index code is being erased.
NOTES:
@ If adjacent index codes are too close to each other, Index Search may
not function properly.
§ If the cassette's safety tab has been removed, index codes cannot be
marked or erased:
@ An index code is not placed on the tape when recording is paused
and then resumed.
POWER
C.MEMORY
REW
Shuttle ring
Counter Reset
To reset the tape counter to zero.
Press C, RESET.
™ Pressing DISPLAY
repeatedly changes the VCR's
displayed indication, (Counter reading —~ Channel* —+
Clock time —-
Remain).
*Channel is not displayed during playback.
Counter Memory
'To return to tape position zero,
During Playback...
[1] Press C. RESET at a point you wish to locate later.
@ The counter will read "0x 00m 00s".
L2] Press:'C. MEMORY.
® Counter' Memory mark is displayed.
(3) When you wish to return to that point, press STOP and then
press REW.
®@ The tape will rewind and stop at about "Ou 00m 00s"
automatically.
(4). To cancel the Counter Memory mode, press C, MEMORY.
Next-Function Memory
'You can "tell" the VCR what to do immediately after rewinding.
During Stop:
;
For automatic start of playback after the tape is rewound...
(1) Press'REW.
(2] Press PLAY within 2 seconds.
For automatic power off after the tape is rewound...
(1). Press REW.
:
{2} Press POWER within 2 seconds.
For automatic timer standby after the tape is rewound...
[i] Press REW. .
{2} Press TIMER within 2 seconds.
& To do the above using the VCR's controls:
During Stop, turn the Shuttle all the way to the left and
release it instead of pressing REW, and then press PLAY or
POWER within 2 seconds.
!
:
:
@ If you want the "next function" to automatically start when
the counter reads "0H 00M 00s" (instead 'of at the beginning
of the tape),.press C. MEMORY so that the counter
memory "M" mark appears on the VCR display panel
before pressing REW or FF.
:
:
EN-23
Advertisement
