CRL SENIOR PRIMA Manual

C.R. LAURENCE CO., INC.
P R O F E S S I O N A L Q U A L I T Y
3-3/16"
(81mm)
2- 5/8"
(67mm)
1/8"
(3mm)
1/8"
(3mm)
7/16"
(11mm)
2- 5/8"
(67mm)
SENIOR PRIMA
4-3/4"

Top or Bottom Mount Hinge

(121mm)
C . N . SRPPH01
AT O
SENIOR PRIMA

Edge Mount Method

Inset Mount Method

SENIOR PRIMA

Glass-to-Glass Hinge

*Maximum
Glass-to-Glass Hinge
Door Capacities
C N . SRPPH02
CAT. NO. SRPPH02
AT O
Using 2 Hinges 145 lbs.(66 kg) 36"(914mm)
Edge Mount Method (1/8" (3mm) to 3/16" (5mm) Clearance) . . . . .Page 4H-6
*NOTE: Do not exceed either maximum weight or width when choosing proper quantity of hinges.
Inset Mount Method (1/8" (3mm) to 3/16" (5mm) Clearance) . . . . .Page 4H-7
*NOTE: Do not exceed either maximum weight or width when choosing proper quantity of hinges. *NOTE: Do not exceed either maximum weight or width when choosing proper quantity of hinges.
1/2" (12mm) Glass
* Maximum C.R. Laurence Co., Inc.
crlaurence.com
Weight
Door Capacities
Using 2 Hinges 145 lbs.(66 kg) 36"(914mm)
For Technical Assistance in the United States and Canada 1.800.421.6144. Press 2, then option 1
*NOTE: Do not exceed either maximum weight or width when choosing proper quantity of hinges. C.R. Laurence Co., Inc. • 2503 E. Vernon Ave., Los Angeles, CA 90058
C.R. Laurence Corporate Headquarters: P.O. Box 58923 Los Angeles, CA 90058-0923; Toll Free Phone (800) 421-6144, Technical Assistance/Extension 777; Toll Free Fax (800) 587-7501
C.R. LAURENCE CO., INC.
P R O F E S S I O n A L Q U A L I T y
* SEE TEMPLATE ON BACK *
Refer to Dimensions Shown
to Ensure Accuracy
4-3/4" (121mm)
(9/16" (14mm) Clearance) . . . . . . . . .Page 4H-2
(9/16" (14mm) Clearance) . . . . . . . . .Page 4H-3
1/2" (12mm) Glass
Weight Width
For technical assistance in the United States call toll free (800) 421-6144; from Canada call toll free (877) 421-6144;
Outside the U.S. and Canada call (323) 588-1281. Ask for Tech Sales at Extension 7740. Toll free fax (800) 458-7496.
Width

Important Information:

Template Options: The Top or Bottom Mount SRPPH01 Hinge offers two choices of templates. Refer to
Important Information:
the lower left hand corner of this page for the selections. The Edge Mount Template has a full leg cutout
Important Information:
that allows a full length vertical seal on the hinge side.
Template Options: The Glass-to-Glass Mount SRPPH02 Hinge offers two choices
The Inset Mount Template enables the door to avoid hitting a towel bar, or some other protrusion from the wall.
of templates. Refer to the lower left hand corner of this page for the various
Template Options: The G lass-to-G lass Mount SR PPH02 Hinge offers two choices of templates. R efer
selections. The Edge Mount Template has a full leg cutout that allows a full length
Optional Pivot Pins: Optional 5˚ Pivot Pins (Cat. No. SRP1VP1N) are sold as a set, one pin for the top
to the lower left hand corner of this page for the various selections. The E dge Mount T emplate has a full
vertical seal on the hinge side.
hinge and one pin for the bottom hinge. These 5˚ offset Pivot Pins allow the installer to adjust the closing
leg cutout that allows a full length vertical seal on the hinge side.
The Inset Mount Template enables the door to avoid hitting a towel bar, or some
position of the door 5˚ inwards or outwards.
other protrusion from the wall.
The Inset Mount T emplate enables the door to avoid hitting a towel bar, or some other protrusion from
Optional Pivot Pins: Optional 5° Pivot Pins (Cat. No. SRP1VP1N) are sold as a set,
the wall.

Specifications:

one pin for the top hinge and one pin for the bottom hinge. These 5° offset Pivot
Optional Pivot Pins: O ptional 5˚ Pivot Pins (Cat. No. SR P1VP1N) are sold as a set, one pin for the
Pins allow the installer to adjust the closing position of the door 5° inwards or
top hinge and one pin for the bottom hinge. These 5˚ offset Pivot Pins allow the installer to adjust the
outwards. closing position of the door 5° inwards or outwards.
Glass Sizes: 1/2"(12mm) thick tempered safety glass
closing position of the door 5˚ inwards or outwards.
Construction: Solid brass
Closing Type: Self-centering when within 15˚ of closed position
Specifications:
Specifications:
Cutout Required
Glass Sizes:
Includes: Gaskets, screws and template
Construction:
Glass Sizes: 1/2"(12mm) thick tempered safety glass

Use of Gaskets:

Closing Type:
Construction: Solid brass
Includes:
Closing Type: Self-centering when within 15˚ of closed position
For 1/2" Glass: Use one thin gasket on one side and one thick gasket on the other side
Cutout Required Includes: G askets, screws and template
For 12mm Glass: Use one thick gasket on both sides

Maximum Door Capacities

Use of Gaskets:

Recommendations:

Maximum Door Weight:
1" (25mm)
Maximum Door Width:
For 1/2" Glass: Use one thin gasket on one side and one thick gasket on the other side
For public safety, we recommend the use of only tempered safety glass.
For 12mm Glass: Use one thick gasket on both sides
Do not use power tools when installing these hinges.
Use of Gaskets:

Maintenance Guidelines:

For 1/2" Glass: Use one thin gasket on one side and one thick gasket on the other side
Recommendations:
For 12mm Glass: Use one thick gasket on both sides
• Never use an abrasive cleaner on the hardware. Many of the components are coated with a clear lacquer
For public safety, we recommend the use of only tempered safety glass.
that will be irreparably damaged if subjected to harsh, abrasive chemicals. Advise your customer that
Recommendations:
Do not use power tools when installing these hinges.
drying the hardware with a clean, soft towel on a daily basis is the best way to maintain the hardware.
For public safety, we recommend the use of only tempered safety glass. Do
If mineral deposits build-up, mix a couple of drops of a mild liquid soap (such as Ivory or a similar
not use power tools when installing these hinges.
product) into a cup of warm water. Using a soft, non-abrasive cloth, clean the hardware. Rinse
Maintenance Guidelines:
thoroughly with clean, warm water and dry.
Maintenance Guidelines:
• Never use an abrasive cleaner on the hardware. Many of the components are coated with a clear lacquer
• Never use an abrasive cleaner on the hardware. Many of the components are
coated with a clear lacquer that will be irreparably damaged if subjected to
that will be irreparably damaged if subjected to harsh, abrasive chemicals. Advise your customer that
harsh, abrasive chemicals. Advise your customer that drying the hardware with
drying the hardware with a clean, soft towel on a daily basis is the best way to maintain the hardware.
a clean, soft towel on a daily basis is the best way to maintain the hardware. If
If mineral deposits build-up, mix a couple of drops of a mild liquid soap (such as Ivory or a similar
mineral deposits build-up, mix a couple of drops of a mild liquid soap (such as
product) into a cup of warm water. Using a soft, non-abrasive cloth, clean the hardware. R inse
Ivory or a similar product) into a cup of warm water. Using a soft, non-abrasive
thoroughly with clean, warm water and dry. cloth, clean the hardware. Rinse thoroughly with clean, warm water and dry.
• 1.800.421.6144 • crlaurence.com
1/2"(12mm) thick tempered safety glass
Solid brass
Self-centering when within 15° of closed position
Gaskets, screws and template
Two Hinges
145 lbs.(66 kg)
36"(914mm)
© Copyright 2005, C.R. Laurence Co., Inc._SDT21_U5
© Co pyr i ght 2 02 2 , C. R. L au re nce Co. , In c_ SDT 2 2 _ 2 2
4H-1
4I-5
4H-5