Table of Contents
Advertisement
ENGLISH
The descriptions in this manual are based on the buttons on the remote
control. Please
read
this manual carefully and use the TV correctly.
This remote uses infrared light. When in use, it should be pointed in the
direction of the TV's remote sensor.
(Some
buttons and services may not be provided depending upon models
or regions.)
How to register the Magic Remote Control
To use the Magic Remote, first pair it with your TV.
1 Put batteries into the Magic Remote and turn the TV on.
2 Point the Magic Remote at your TV and press the
O
Wheel (OK)
on
the remote control.
*
If the TV fails to register the Magic Remote, try again after turning the
TV off and back on.
How to deregister the Magic Remote Control
Press the
G)
(Back)
and@) (Home) buttons at the same time, for five
seconds, to unpair the Magic Remote with your TV.
*
Press and hold the@)
(Home)
and@(Q.
Settings)
buttons for
more than 5 seconds to disconnect and re-register the Magic Remote
at the same time.
&
•
It is recommended that an Access Point
(AP)
be
located
more than
0.2 m (0.65 ft) away from the TV. If the AP is installed closer than
0.2 m (0.65 ft), the Magic remote control may not perform as expected
due to frequency interference.
Using Always Ready
(Depending
upon model)
You can operate the TV and connect to Bluetooth with direct voice
recognition while the power is off.
*
@-
[@)
-+[General)-+ [Always
Ready], setting
[Enable
the
function) to on.
*
Pressing the~ button while watching TV switches the screen to
[Always
Ready) that is turned on, and pressing the~ button once
more turns the screen to [Always Ready) that is turned off.
*
Press the@) (Home) button or the
6)
(Back)
button to watch TV
when the screen is in [Always Ready) that is turned on.
*
Press the
O
Wheel (OK)
button to display the wallpaper when the
screen is in [Always Ready) that is turned off, and press the~ button
to watch TV.
9Note
• Using
Always Ready may increase energy consumption.
•
For models with motion sensors, such as G3/M3, if you set screen
on with the motion sensor,
the
TV will turn on by recognising the
motion.
•
For more information about
the
feature, refer to the@-+
[@)
-+[Support)-+
[User Guide)-+ [Troubleshooting)-+ [Learn More
About Always Ready).
Connecting Smart Devices using NFC Tagging
NFC
is
technology that uses Near Field Communication (13.56 MHz),
allowing you to conveniently send and receive information without
separate settings. By bringing a smart device near
the
NFC-enabled
remote control, you can install
the
LG ThinQ app and connect the device
to the TV.
1 Turn on NFC
in
the smart device's settings. To use NFC with Android
devices, set the NFC option
to
enable'read/write tags'in the smart
device's settings. The NFC settings may vary depending upon the
device.
2 Bring the smart device near the
ml
(NFC)
on the remote control. The
required distance for NFC tagging is about 1 cm
(0.39
inches).
3 Follow the instructions to install the LG ThinQ app on your smart
device.
4 Retagging the smart device to the remote control allows you to
conveniently access various features on the connected TV through the
LG ThinQ app.
f)
Note
•
This feature is available for NFC-enabled smart devices only.
• This feature is only available if the remote control has an NFC logo.
Specifications
.
~(MmGN,MmGA)
Frequency range
Bluetooth
2,400 to 2,483.5 MHz
NFC'
13.56 MHz
*
Only MR23GN
Output Power
(Max.)
BdBm
Advertisement
Table of Contents
