Table of Contents
Advertisement
Before the Timer Starts
HB Check that tape direction is correct. This ts important especially when Reverse Mode is off.
MB Set Reverse Mode on if you want to record on both sides of the tape.
Setting the SLEEP Timer
MM The VOLUME control is automatically set to 0 when ONCE REC Timer is recording.
Use the Sleep Timer to turn the Unit off after a certain number of minutes when it is playing. By setting
this timer, you can fal] asleep to music and know your Unit will turn off by itself rather than play all night.
It is very easy, and can be very disappointing, to forget to put ina
ME You can only set the Sleep Timer when the Unit is on and a source is playing.
tape, or to accidentally leave a tape in Tape Tray you don't want
recorded over. Although this happens to almost everyone at one time
To set the SLEEP Timer, follow this procedure:
or another, we hope it won't happen to you!
"$2 with the System on and
a source playing,
SLEEP
;
ress the SLEEP
button on the Remote
To Change the Recording Timer Setting
(C5)
Sitio
-=)
7
er
7
To change the settings for the ONCE REC Timer, repeat the setting procedure from the beginning.
The message "SLEEP" appears on the display.
Se:
tingle.
whe
Turning the ONCE
REC
Timer On and Off
Set the length of time you want the source to play before shutting
Once the ONCE REC Timer has been used to record a source. the setting is maintained but the Timer is
off.
4
ae
set to OFE
*
Each ume you press this button while the "SI-EEP™ indicator is blinking. it changes the number of
a
To Turn the REC
Timer Off Before the Timer Starts.
minutes shown on the display in this sequence:
4
» Press the MENU
button.
+ 10 — 20 — 30 > 60 ~ 90 © 120 — Cancelled ~ (back to the beginning)
"DAILY" appears on the display and the DAILY indicator in the "TIMER" section of the menu
4
display blinks.
When the number of minutes you want show's on the display, just wait 5 seconds until the "SLEEP"
display blinks,
Press the SLEEP button until the number of minutes you want appears on the display.
Press the
CANCEL button.
To Cancel the SLEEP Timer Setting
|
Press the SLEEP button until the "SLEEP"
indicator goes off on the display.
Tuming oft the Unit also cancels the SLEEP Timer.
cB
CANCEL
"REC OFF" appears on the display and the REC indicator in the TIMER section of the menus gaes
out.
e
4
To Record at the Same Time Again.
MENU
Timer Priority
Press the MENU button.
"DAILY™ appears on the display and the DAILY indicator in the "TIMER" section of the menu
Since each timer can be set independently, you may wonder what happens if the settings overlap. Here are
display blinks.
the priorities for each timer:
WE The ONCE REC Timer always has priority. This means that:
"
» Press the up or down cursor key (»» ~ or Vv <<) until "REC" blinks
*
If another timer is set to come on during a time when the ONCE REC Timer is operating, the
on the display.
other timer just won't come on at all, so you will always get the entire program on tape.
"ONCE REC" appears on the display and the REC indicator in the "TIMER" section of the menu
*
Ifthe ONCE REC Timer is set to come on while another timer is operating, the other timer will
display blinks.
shut off 10 seconds before the ONCE REC Timer is set to turn on, and the ONCE REC Timer will
then take over.
Mi The SLEEP Timer has the least priority. This means that if the SLEEP Timer is set while the DAILY
- Press
the ENTER
button.
Timer is operating, the DAILY Timer settings are caneelled. However. if the DAILY Timer is set to
come while the SLEEP Timer is operating. the SLEEP Timer setting will be cancelled and the Unit
will use the settings trom the DAILY Timer.
, Press the SET button.
ed
Geese
bas
~ The DAILY indicator in the TIMER section of the menu changes from a blinking display to a steady
display. The ON TIME, OFF TIME, and preset channel number are displayed then the display reverts
to the previous display, before the Timer was set.
CAUTION: If the System is unplugged, or a power failure occurs, the
timer setting will be erased in a few days. If the settings are erased in
ON
one
PPLE
this way, reset the timer settings.
ae mEL
a)
,
SLEEP
Timer
|
22:00
22:30
23:00
22:00
22:30
The ONCE REC Timer has prionty.
Example 2 7
:
Setting
Operation
ON
OFF
ON
OFF
ONCE REC
!
[
a
Timer
|
ON
|
OFF
}
|
DAILY
|
!
|
!
Timer
21:30
22:00
22:30
23:00
21:30
22:30
The ONCE REC Timer has priority.
40
441
Cc-1
YSSC1
Advertisement
Table of Contents
