Table of Contents
Advertisement
Tie)
Division
Use to nullify output data, DOAL,
DOBL, DOAR and DOBR
("L" to nullify).
NDACC
46
DOUTON
47
Input signal to select ON/OFF of
digital output.
[ At"H" :ON
At"L" : OFF
Control signal to set the mode of
digital filter.
Data signal to set the mode of
digital filter.
Digital filter's mode setting data
sampling pulse output.
GND terminal.
Bit clock of DIL, DIR data signal.
WCKI
Word clock of DIL, DIR data signal.
pes [oc [1 [rane oa
*1C302 (SM5813): Digital filter
fo] mt | ln | tm |
Division
es
[ce | [aac
[aa
CKDV
fs |
nc
|
1
| Not used, connected to GND.
Clock input terminal.
XTI
Input terminal to select input
frequency of XTI terminal.
Mode select data signal.
'
Reset signal input (reset at "L" ).
Use to select either two's
complement or COB ("H" for two's
complement: "L" for COB).
beng CKSL= ce
CKDV="L"
7
Eee
Clock output terminal.
8 |
VSS1
ied
GND terminal.
Clock output terminal
fs]
oo
|e
| aaa used: oper
Use to select either Jitter free
SYN
mode or forced sync. mode ("H" for
Jitter free mode: "L" for forced
sync. mode).
al
NG
Mode select control signal
Ea (MS2MS3)
ena.
pa [remem [1
pa eee |
Starting signal of operation for
digital filter.
vo
Division
Vv
Vv
NLRCK
D
Ss
N
Input terminal of digital output
signal.
Not connected.
Digital output signal.
Digital output signal
(Not used, open).
D
S
Cc
Cc
Input terminal to select output bits
data.
fe)
NC
ee
Not used, connected to GND.
with a period of fs (Not used, open).
Sample rate (fs) clock of input data
("H" : Loh, "L" : Roh)
SL-P999
Disc holder "Open" detection
¢ 10401 (MN1554PEZ-1): System control
|
Division
[Yvert
on
oe Cc
1 [neta
eomectsie 7
Sub-code block (Q data) clock input
(75Hz)
Sub-code block (Q data) clock input
(7.35kHz)
a2
(Not used, open)
> D 72)
na no
o 8 4|83|8
2
x z > >
0
zs =
>
° fe x
LOSE
Disc hoider "Close" detection
(Not used, connected to GND)
(Not used, connected
to GND)
Processing status input from signal
processing LSI
TOC reading control (ON at "L")
(connected to GND)
Optical servo condition (focus)
input
Optical servo condition
(track cross) input
Data receipt command signal
Data transmission command
signal
Data discrimination signal
Data lock signal
Key scan signal
Ww
oO
CLK
34
LOCK
Sub-code (Q data) input
Reset signal input
ENSE
wD
° n
n r
z <
5 = Q zx z
c?)
(2) ce)
xz zx
10
5
13
37
ECV
P20
5
Not used (connected to +5V)
P23
Loading motor "Open" command
po fe
(Not used, open)
Traverse "Reverse" command
signal
AV.F
Traverse "Forward" command
signal
SLOW
4
Pane
44
| DATA3
17
| MUTE
CLOSE
30
Loading motor "Close" command
>»
a
on
Not connected
Clock terminal
Clock input
Optical servo condition input
(Not used, open)
GND terminal
Muting control
Command
data output
Data clock output
{command clock signal)
Data output (command load signal)
Optical output control signal
Emphasis signal output
| Notconnected
=
connected
Zz fo)
o|ju
oa LS)
OSC2
RV.R
osc1
Optical servo IC control signal
(KICKR: Kick direction [reverse]
command)
CNT4
7
4 4 iz
ro)
Optical servo IC control signal
(KICKF: Kick direction [forward]
command)
(TRON: Tracking servo)
Optical servo IC control signal
(FOON:
Focus servo)
CNT3
DMUTE
DATA
CLK
ba
id
z Ss Ls)
61
rc o
ft a
< =] o
62
OUTON
i=] °
il
z
Law) N
63
CNT1
Zim]
go oOo;
2D
x=
Advertisement
Table of Contents
