Adjusting The Feet; Connecting To The Drain; Electrical Connection - Beko WKY 71033 PTLYW2 User Manual

hose (right) (max. 25 ºC) is for cold water inlet.
WARNING:
A Ensure that the cold and hot water
connections are made correctly when installing the
product. Otherwise, your laundry will come out hot
at the end of the washing process and wear out.
2. Tighten all hose nuts by hand. Never use a tool
when tightening the nuts.
3. Open the taps completely after making the
hose connection to check for water leaks at
the connection points. If any leaks occur, turn
off the tap and remove the nut. Retighten the
nut carefully after checking the seal. To prevent
water leakages and damages caused by them,
keep the taps closed when the machine is not
in use.
2.5 Connecting to the drain
• The end of the drain hose must be directly
connected to the wastewater drain or to the
washbasin.
A WARNING:
Your house will be flooded if the hose
comes out of its housing during water discharge.
Moreover, there is risk of scalding due to high
washing temperatures! To prevent such situations
and to ensure smooth water intake and discharge
of the machine, fix the end of the discharge hose
tightly so that it cannot come out.
• The hose should be attached to a height of at
least 40 cm, and 100 cm at most.
• In case the hose is elevated after laying it on
the floor level or close to the ground (less than
40 cm above the ground), water discharge
becomes more difficult and the laundry may
come out excessively wet. Therefore, follow the
heights described in the figure.
• To prevent flowing of dirty water back into the
machine and to allow for easy discharge, do
not immerse the hose end into the dirty water
or do not drive it in the drain more than 15 cm.
If it is too long, cut it short.
• The end of the hose should not be bent, it
should not be stepped on and the hose must
not be pinched between the drain and the
machine.
• If the length of the hose is too short, use it by
adding an original extension hose. Length of
51 / EN
the hose may not be longer than 3.2 m. To avoid
water leak failures, the connection between the
extension hose and the drain hose of the product
must be fitted well with an appropriate clamp as
not to come off and leak.

2.6 Adjusting the feet

WARNING:
A
In order to ensure that the product
operates more silently and vibration-free, it must
stand level and balanced on its feet. Balance
the machine by adjusting the feet. Otherwise,
the product may move from its place and cause
crushing and vibration problems.
1. Loosen the lock nuts on the feet by hand.
2. Adjust the feet until the product stands level and
balanced.
3. Tighten all lock nuts again by hand.
A
WARNING:
Do not use any tools to loosen the
lock nuts. Otherwise, they will get damaged.
2.7 Electrical connection
Connect the product to a grounded outlet
protected by a 16 A fuse. Our company shall not
be liable for any damages that will arise when the
product is used without grounding in accordance
with the local regulations.
• Connection must comply with national
regulations.
• Power cable plug must be within easy reach after
installation.
• If the current value of the fuse or breaker in the
house is less than 16 Amps, have a qualified
electrician install a 16 Amp fuse.
• The voltage specified in the "Technical
specifications" section must be equal to your
mains voltage.
• Do not make connections via extension cables or
multi-plugs.
B
WARNING:
Damaged power cables must be
replaced by the Authorized Service Agents.
Transportation of the product
1. Unplug the product before transporting it.
2. Remove water drain and water supply
connections.
3. Drain all water that has remained in the product.
See 6.5
4. Install transportation safety bolts in the reverse
order of removal procedure; see 3.3.
C
Never move the product without the
transportation safety bolts properly fixed in place!
WARNING:
A
Packaging materials are
dangerous to children. Keep packaging materials
in a safe place away from reach of the children.
Washing Machine / User's Manual