Table of Contents
Advertisement
1 Notice
Trademarks are the property of Koninklijke Philips N.V. or their
respective owners.
Funai Corporation reserves the right to change products at any time
without being obliged to adjust earlier supplies accordingly.
The material in this Owner's manual is believed adequate for the
intended use of the system. If the product or its individual modules or
procedures are used for purposes other than those specified herein,
confirmation of their validity and suitability must be obtained. Funai
Corporation warrants that the material itself does not infringe any
United States patents. No further warranty is expressed or implied.
Funai Corporation cannot be held responsible neither for any errors in
the content of this document nor for any problems as a result of the
content in this document. Errors reported to Funai Corporation will be
adapted and published on the Funai Corporation support website as
soon as possible.
Pixel characteristics
This LCD product has a high number of color pixels. Although it has
effective pixels of 99.999 % or more, black dots or bright points of light
(red, green or blue) may appear constantly on the screen. This is a
structural property of the display (within common industry standards)
and is not a malfunction.
Warranty
No components are user serviceable. Do not open or remove covers to
the inside of the product. Repairs may only be done by service centers
and official repair shops. Failure to do so shall void any warranty, stated
or implied.
Any operation expressly prohibited in this manual, any adjustments or
assembly procedures not recommended or authorized in this manual
shall void the warranty.
Federal communications commission notice
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
●
Increase the separation between the equipment and the receiver.
●
Connect the equipment into an outlet on a circuit different from that
●
to which the receiver is connected.
Consult the dealer or an experienced radio or television technician
●
for help.
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept interference received,
including interference that may cause undesired operation.
Declaration of conformity
: PHILIPS
Trade name
: Funai Corporation, Inc.
Responsible party
: 32PFL3453/F7 A
Model
: 12489 Lakeland Road, Santa Fe
Address
Springs, CA 90670, USA*
Telephone number : 1 833 978 3323
* This is not the mailing address for Open Source Software or Customer
service.
Modifications
This apparatus may generate or use radio frequency energy. Changes
or modifications to this apparatus may cause harmful interference.
Any modifications to the apparatus must be approved by Funai
Corporation.
The user could lose the authority to operate this apparatus if an
unauthorized change or modification is made.
Back to Contents
Cables
Connections to this device must be made with shielded cables with
metallic RFI/EMI connector hoods to maintain compliance with FCC
Rules and regulations.
The following FCC applies to the wireless LAN
adapter included in this product.
FCC caution: Any changes or modifications not expressly
approved by the party responsible for compliance could void the
user's authority to operate this equipment.
This transmitter must not be co-located or operated in conjunction
with any other antenna or transmitter.
FCC RF Exposure Compliance
This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment and meets the FCC radio
frequency (RF) Exposure Guidelines. This equipment should be
installed and operated keeping the radiator at least 20 cm or more
away from your body.
Compliance with FCC requirement 15.407(c)
Data transmission is always initiated by software, which is the
passed down through the MAC, through the digital and analog
baseband, and finally to the RF chip. Several special packets are
initiated by the MAC. These are the only ways the digital baseband
portion will turn on the RF transmitter, which it then turns off at
the end of the packet. Therefore, the transmitter will be on only
while one of the aforementioned packets is being transmitted. In
other words, this device automatically discontinue transmission in
case of either absence of information to transmit or operational
failure.
Positioning the TV
Large screen TVs are heavy. 2 people are required to carry and handle
●
a large screen TV.
Make sure to hold the upper and bottom
●
frames of the unit firmly as illustrated.
Install the unit in a horizontal and stable
●
position.
Do not install the unit in direct sunlight or in
●
a place subject to dust or strong vibration.
Depending on the environment, the
●
temperature of this unit may increase
slightly. This is not a malfunction.
When installing this unit in a temperate environment, avoid a place
●
with rapid temperature changes.
Operating temperature: 41 °F (5 °C) to 104 °F (40 °C)
–
This unit should not be used in a tropical environment as it has not
●
been evaluated under such conditions.
No objects should be placed directly on or under this unit, especially
●
lighted candles or other flaming objects.
Depending on your external devices, noise or disturbance of the
●
picture and/or sound may be generated if the unit is placed too close
to them. In this case, please ensure enough space between the
external devices and the unit.
Do not insert the AC power cord into the power socket outlet before
●
all the connections are made.
Ensure that you always have easy access to the AC power cord and
●
outlet to disconnect the TV from the AC outlet.
Before you move the TV, disconnect attached cables to prevent
●
damage to connectors, especially the TV tuner.
Be sure to unplug the AC power plug from the AC outlet before
●
moving or carrying the unit.
When moving the TV and then setting it down, please be careful not
●
to pinch the AC power cord under the unit.
Do not place this unit in an area where it may be exposed to water,
●
oil or grease such as:
near a bathtub, basin, kitchen sink, washing tub, swimming pool,
kitchen exhaust fan, etc., or in a damp basement.
Regulatory notices
: To prevent injury, this apparatus must be securely
WARNING
attached to the furniture/wall in accordance with the
instructions. Tipping, shaking, or rocking the unit may
cause injury/death.
5
.
English
Advertisement
Table of Contents
