Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Grundig GU-CI-AP12616F
Summary of Contents for Grundig GU-CI-AP12616F
- Page 2 Use of this document and the subsequent results shall be entirely on the user’s own responsibility. Abetechs GmbH (Grundig Security) reserves the right to change the contents of this document without prior notice. Design and specifications are subject to change without prior notice.
- Page 3 OPEN SOURCE SOFTWARE LICENSE INFORMATION The software components provided with Grundig products may contain copyrighted software that is licensed under various open source software licenses. For detailed information about the...
- Page 4 The appearance of the products, functions and firmware or software upgrade may differ from this manual. GRUNDIG reserves the right to perform needed changes without prior notice. Safety Instructions Make sure that you only use the power adapter that is specified in the specifications sheet of the product.
- Page 5 Improper use or replacement of the battery may result in the hazard of explosion. Do not use any accessories that are not recommended by GRUNDIG. Do not modify the product in any way. If the product starts to smell or smoke comes out of the device, immediately stop using the product and disconnect it from the power supply to prevent fire or electric shocks.
- Page 6 Do not install the product near heat sources, like radiators or other equipment that produces some heat. If the product is not classified by any IP class, do not install the product in very cold or hot temperatures (please refer to the working temperature specified in the specification sheet of the product), dusty, dirty or damp environment.
- Page 7 Special Installation Instructions for IP Cameras Make sure that the latest firmware is installed on the IP Device. You may get the latest firmware from techsupport@grundig-security.com.
-
Page 8: Table Of Contents
3.1 Wiring ................12 3.2 Activating the Camera ........... 13 3.2.1 Activation via Web Browser ........ 13 Activation via Grundig IP-Finder Tool ....14 3.3 Modifying the IP Address ..........16 4 Accessing via Web Browser ............18 4.1 Initializing the Memory Card ......... 20... -
Page 9: Appearance Description
1 Appearance Description The overview of the network fisheye camera is shown below. Figure 1-1 Overview of Fisheye Camera Figure 1-2 SD-card interface... -
Page 10: Installation
2 Installation Before you start: Plan the cable routing before installation. This camera series supports cable-routing through the ceiling and through side outlet. ● Through the ceiling: you should cut a hole in ceiling and route the cables in advance. ●... - Page 11 2 Drill 4 holes into the wall/ceiling and put the expansion bolts into them. Fix the mounting base on the wall/ceiling. 3 Fix the camera onto the mounting base until it clicks into place. Figure 2-2 fix the camera on mounting base 4 Adjust the horizontal and vertical viewing angle of the camera.
-
Page 12: Setting The Ip-Camera Over The Lan
3 Setting the IP-Camera over the LAN Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, contact your dealer or the nearest service center for help. -
Page 13: Activating The Camera
Activation via Web Browser and Activation via Grundig IP-Finder Tool are supported. We will take activation via Grundig IP-Finder Tool and Activation via Web Browser as examples to introduce the camera activation. -
Page 14: Activation Via Grundig Ip-Finder Tool
4. Confirm the password. 5. Click OK to save the password and enter the live view interface. Activation via Grundig IP-Finder Tool The Grundig IP-Finder Tool is used for detecting the online device and activating the camera. - Page 15 Get the Grundig Finder Tool from the supplied disk or the official website and install the software according to the prompts. Follow the steps to activate the camera, please refer to the User manual for other two activation methods. Steps: 1.
-
Page 16: Modifying The Ip Address
To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your Use the Grundig IP-Finder Tool to search and change the IP address of the device. We take modifying the IP Address via Grundig IP-Finder as an example to introduce the IP address modification. - Page 17 Figure 3-5 Modify the IP Address 4. Input the admin password and click Update to activate your IP address modification. The batch IP address modification is supported by the Grundig IP- Finder. Please refer to the User Manual of Grundig IP-Finder for details.
-
Page 18: Accessing Via Web Browser
4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows 7, Windows 8, Windows 2008 (32/64 bit), Windows 2003, Windows XP, Windows 2000 (32 bit) CPU: Intel Core Duo2 or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 10 and above version, Apple Safari 16 and above version, Mozilla Firefox 52.0 and above version and Google Chrome 57.0 and above version. - Page 19 4. Click Login. Login Interface 5. Install if necessary, the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in.
-
Page 20: Initializing The Memory Card
Initializing the Memory Card Steps: Check the memory card status by tapping on “Status” in the device → settings interface on Device Disk. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to “OK”. You can then start recording any event triggered video in the camera such as motion detection.
Need help?
Do you have a question about the GU-CI-AP12616F and is the answer not in the manual?
Questions and answers