1. Manuals
  2. Brands
  3. peerless-AV Manuals
  4. TV Mount
  5. PLAV70-UNL-S
  6. Installation and assembly manual

peerless-AV PLAV70-UNL-S Installation And Assembly Manual

Universal articulating swivel double-arm for 42" - 95" plasma screens
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Installation and Assembly - Universal Articulating
Swivel Double-Arm for 42" - 95" Plasma Screens
2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com
Models:
PLAV70-UNL,
PLAV70-UNL-S, PLAV70-UNLP,
PLAV70-UNLP-S
Max UL Load Capacity:
ISSUED: 06-05-06 SHEET #: 202-9142-10 (2013-03-17)
200 lb (91 kg)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PLAV70-UNL-S and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for peerless-AV PLAV70-UNL-S

Summary of Contents for peerless-AV PLAV70-UNL-S

  • Page 1 Swivel Double-Arm for 42" - 95" Plasma Screens PLAV70-UNLP-S Max UL Load Capacity: 200 lb (91 kg) 2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com ISSUED: 06-05-06 SHEET #: 202-9142-10 (2013-03-17)

  • Page 2: Tools Needed For Assembly

    NOTE: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact your local distributor.

  • Page 3: Parts List

    Parts List PLAV70-UNL PLAV70-UNL-S PLAV70-UNLP PLAV70-UNLP-S Description Part # Part # wall plate 201-1040 201-4040 tilt-roll assembly 201-1042 201-4042 arm assembly 201-1044 201-4044 wall support arm axle 201-1041 201-1041 vinyl trim 600-1012 600-1012 M10 x 15mm screw bolt 520-9262 520-9262 .505 x .062"...
  • Page 4 Parts List PLAV70-UNL PLAV70-UNL-S PLAV70-UNLP PLAV70-UNLP-S Description Part # Part # Part # Part # AA adapter bracket 201-1110 201-4110 201-1110 201-4110 BB shallow adapter bracket 202-1655 202-4655 202-1656 202-4656 CC 4mm allen wrench 560-9646 560-9646 560-0072 560-0072 Phillips Adapter Bracket Fasteners...

  • Page 5: Installation To Wood Stud Wall

    Installation to Wood Stud Wall WARNING • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. • Tighten wood screws so that wall plate is fi rmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power.
  • Page 6 Installation to Solid Concrete or Cinder Block Wall WARNING • When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1"...
  • Page 7 WARNING • If you are uncertain that product is properly installed, call customer care. Note: There are three mounting positions. The center position is shown right. Arm assemblies must be mounted with one mounting hole separating them. Slide washers (J) over wall support arm axles (D). Next, insert plastic caps (N) into axles.
  • Page 8 Attach two pieces of vinyl trim (E) to wall plate (A). Next, attach one piece of vinyl trim to bottom of swivel box on arm assembly (C). Insert one fi nishing cap (L) into each unused hole of wall plate (A). SWIVEL BOX Insert and tape carriage bolt (I) into top hole of tilt-roll assembly (B).
  • Page 9 WARNING • Use an assistant or mechanical lifting equipment to safely lift and position the plasma TV. Insert two M10 screws (F) into swivel box on arm assembly (C) as shown. Leave approx. 1/4" of exposed thread. SWIVEL BOX .25" Hook tilt-roll assembly (B) onto M10 screws (F).

  • Page 10: Installing Adapter Brackets

    Installing Adapter Brackets WARNING • Tighten screws so adapter brackets are fi rmly attached. Do not tighten with excessive force. Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque. •...
  • Page 11 For Flat Back Display Begin with the shortest length screw, hand thread through multi-washer and adapter bracket into display as shown below. Screw must make at least three full turns into the mounting hole and fi t snug into place. Do not over tighten.

  • Page 12: Mounting And Removing Flat Panel Screen

    Mounting and Removing Flat Panel Screen WARNING • Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television. Refer to mount instruction sheet for attachment of adapter bracket to mount. Hook adapter brackets (BB) onto adapter bracket (AA), then slowly swing screen in as shown. Turn screws clockwise at least six times to prevent screen from being removed as shown in detail 4.
  • Page 13 Depending on the specifi c size & weight of the plas- If it is too diffi cult to adjust roll of plasma, loosen ma, articulating swing arm may be angled at different screws shown in fi gure 9.1 using a phillips positions, causing plasma to appear to lean sideways screwdriver.

  • Page 14: Limited Five-Year Warranty

    Limited Warranty or impose any obligation on Peerless in connection with the sale of any Peerless® product. This warranty gives specifi c legal rights, and you may also have other rights which vary from state to state. www.peerless-av.com © 2014 Peerless Industries, Inc.

This manual is also suitable for:

Plav70-unlp-sPlav70-unlPlav70-unlp

Table of Contents