Advertisement
Quick Links
Installation and Assembly - Universal Articulating
Models: PLAV70
Swivel Double-Arm for 42" - 95" Plasma Screens
Max UL Load Capacity: 200 lb (91 kg)
2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com
ISSUED: 05-02-06
SHEET #:202-9089-6
(2017-01-13)
Advertisement
Related Manuals for peerless-AV PLAV70
Summary of Contents for peerless-AV PLAV70
- Page 1 Models: PLAV70 Swivel Double-Arm for 42" - 95" Plasma Screens Max UL Load Capacity: 200 lb (91 kg) 2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com ISSUED: 05-02-06 SHEET #:202-9089-6 (2017-01-13)
- Page 2 NOTE: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact your local distributor.
- Page 3 Parts List Description Part # wall plate 201-1040 tilt-roll assembly 201-1042 arm assembly 201-1044 wall support arm axle 201-1041 vinyl trim 600-1012 M10 x 1.5 x 15mm screw 520-9262 .062" nylon washer 540-1074 tilt adjustment knob 560-0108 carriage bolt 3/8"-16 x 3.25" 520-1315 .062"...
- Page 4 Installation to Wood Stud Wall WARNING • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. • Tighten wood screws so that wall plate is fi rmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power.
- Page 5 Installation to Solid Concrete or Cinder Block Wall WARNING • When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1"...
- Page 6 WARNING • If you are uncertain that product is properly installed, call customer care. Note: There are three mounting positions. The center position is shown right. Arm assemblies must be mounted with one mounting hole separating them. Slide washers (J) over wall support arm axles (D). Next, insert plastic caps (N) into axles.
- Page 7 Attach two pieces of vinyl trim (E) to wall plate (A). Next, attach one piece of vinyl trim to bottom of swivel box on arm assembly (C). Insert one fi nishing cap (L) into each unused hole of wall plate (A). SWIVEL BOX NOTE: Refer to adapter bracket instruction sheet for attachment of adapter bracket to plasma before proceed- ing with step 5.
- Page 8 WARNING • Use an assistant or mechanical lifting equipment to safely lift and position the plasma TV. Insert two M10 screws (F) into swivel box on arm assembly (C). Leave approximately 1/4" of exposed thread. SWIVEL BOX .25" Hook tilt-roll assembly (B) onto M10 screws (F). Insert carriage bolt (I) into slot of swivel box as shown in fi...
- Page 9 Depending on the specifi c size & weight of the plas- If it is too diffi cult to adjust roll of plasma, loosen ma, articulating swing arm may be angled at different screws shown in fi gure 7.1 using a phillips screw- positions, causing plasma to appear to lean sideways driver.
- Page 10 Limited Warranty or impose any obligation on Peerless in connection with the sale of any Peerless® product. This warranty gives specifi c legal rights, and you may also have other rights which vary from state to state. www.peerless-av.com © 2017 Peerless Industries, Inc.
Need help?
Do you have a question about the PLAV70 and is the answer not in the manual?
Questions and answers