Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Valentin WMX 5001
Summary of Contents for Valentin WMX 5001
- Page 2 No part of this document may be reproduced in any form (print, photocopy, or any other method) or edited, copied, or distributed electronically without written permission from Carl Valentin GmbH. Due to the constant further development of our devices discrepancies between manual and device can occur.
-
Page 3: Table Of Contents
Wipe-On Applicators Table of Contents Table of Contents Introduction ................5 General Instructions ..............5 Intended Use ................6 Safety Instructions ..............6 Product Description .............. 9 Product Designation ..............9 Function ................... 9 Overview ................10 Technical Data ..............11 Installation ................ - Page 4 Table of Contents Wipe-On Applicators Operating Manual 10.23...
-
Page 5: Introduction
Wipe-On Applicators Introduction Introduction General Instructions Important information and instructions in this document are designated as follows: DANGER identifies an extraordinarily great and immediate danger which could lead to serious injury or even death. WARNING identifies a possible danger could lead to serious bodily injury or even death if sufficient precautions are not taken. -
Page 6: Intended Use
Introduction Wipe-On Applicators Intended Use The device is a state-of-the-art device which complies with the recognized safety-related rules and regulations. Despite this, a danger to life and limb of the user or third parties could arise and the device or other property could be damaged while operating the device. The device may only be used while in proper working order and for the intended purpose. - Page 7 Wipe-On Applicators Introduction Carry out only the actions described in these operating instructions. Any work beyond this may only be performed by the manufacturer or upon agreement with the manufacturer. Unauthorized interference with electronic modules or their software can cause malfunctions. Other unauthorized work or modifications to the device can endanger operational safety.
- Page 8 Introduction Wipe-On Applicators Operating Manual 10.23...
-
Page 9: Product Description
Wipe-On Applicators Product Description Product Description 2.1 Product Designation Designation Specification Device Type WMX 5001 right side, ILX 56/8, ILX 54/12, spring mounted right side WMX 5101 left side, ILX 56/8, ILX 54/12, spring mounted left side WMX 5201 right side,... -
Page 10: Overview
Product Description Wipe-On Applicators 2.3 Overview NOTICE! The figure of overview applies to wipe-on applicators WMX 5001 / 5101 / 5201 / 5301 - right version. Figure 1 Return pulley Return pulley Return pulley Return pulley Dispensing edge Rocker lever... -
Page 11: Technical Data
Wipe-On Applicators Technical Data Technical Data Wipe-on applicator WMX 5001 / 5101 WMX 5201 / 5301 Print module ILX 56/8 and ILX 54/12 ILX 80/8 and 81/12 Passage width 60 mm 90 mm Min label width 20 mm 20 mm... - Page 12 Technical Data Wipe-On Applicators Operating Manual 10.23...
-
Page 13: Installation
Wipe-On Applicators Installation Installation 4.1 Unpack the Wipe-On Applicator Lift the wipe-on applicator out of the box. Check the wipe-on applicator for transport damages. Check delivery for completeness. Scope of Delivery • Wipe-on applicator • 2x holding shaft (length 300 mm). •... -
Page 14: Connect The Wipe-On Applicator
Installation Wipe-On Applicators 4.4 Connect the Wipe-On Applicator NOTICE! The figure of overview applies to wipe-on applicators WMX 5001 / 5101 / 5201 / 5301. E(4x) D(4x) Figure 2 1. Insert the cylinder pins (B) on the wipe-on applicator into the intended drillings of the carrier plate (A) of the printing system. -
Page 15: Install The Pressure Roller (Optional)
Installation 4.5 Install the Pressure Roller (Optional) NOTICE! The figure of overview applies to wipe-on applicators WMX 5001 / 5101 / 5201 / 5301 Fix the pressure roller (C) with the washer (B) and clamping lever (A) to the wipe-on applicator. -
Page 16: Insert The Label Material
Installation Wipe-On Applicators 4.7 Insert the Label Material NOTICE! The figure of overview applies to wipe-on applicators WMX 5001 / 5101 / 5201 / 5301. Label run - Printing system and wipe-on applicator Figure 5 1. Insert the label material (B) according to the label run up to the dispensing edge (E) of the printing system. -
Page 17: Adjust The Displacement Unit
Wipe-On Applicators Installation 4.8 Adjust the Displacement Unit NOTICE! When changing the label height it is necessary to move the return pulley of displacement unit (F) in order to bring the beginning of the label material into a suitable apply position. Figure 6 NOTICE! The angle position of clamping lever (G) can be changed by... - Page 18 Installation Wipe-On Applicators Operating Manual 10.23...
-
Page 19: Adjustments
Wipe-On Applicators Adjustments Adjustments 5.1 Adjust the Dispensing Angle NOTICE! The figure of overview applies to wipe-on applicators WMX 5001 / 5101 / 5201 / 5301. Figure 7 1. Move the dispensing rocker (D, Figure 5) forwards/upwards by pulling out the knurled knob (C, Figure 5). 2. - Page 20 Adjustments Wipe-On Applicators Minimum angle adjustment (16 degrees) Maximum angle adjustment (36 degrees) Figure 8 5. Turn the internal rewinder (A, Figure 5) of the printing module as long as the backing paper is again tensioned. 6. Press the dispensing rocker (D, Figure 5) again upwards and engage.
-
Page 21: Adjust The Pressur Roller (Optional)
Wipe-On Applicators Adjustments 5.2 Adjust the Pressur Roller (Optional) NOTICE! The figure of overview applies to wipe-on applicators WMX 5001 / 5101 / 5201 / 5301. Figure 9 NOTICE! The adjustments take place in depending on the label material and the product surface. 1. -
Page 22: Adjust The Pressure Brush (Optional)
Adjustments Wipe-On Applicators 5.3 Adjust the Pressure Brush (Optional) NOTICE! The figure of overview applies to wipe-on applicators WMX 5001 / 5101 / 5201 / 5301. Figure 10 NOTICE! The adjustments take place in depending on the label material and the product surface. 1. -
Page 23: Adjust The Labelling Position
Wipe-On Applicators Adjustments 5.4 Adjust the Labelling Position NOTICE! The figure of overview applies to wipe-on applicators WMX 5001 / 5101 / 5201 / 5301. NOTICE! In order to operate the printing system with the wipe-on applicator in the dispenser mode, the dispenser offset must be set to 0. For a detailed description for adjusting the dispenser offset, please refer to the chapter Dispenser I/O in the operating manual of the printing system. - Page 24 Adjustments Wipe-On Applicators NOTICE! In order to stretch the backing paper (B) on the internal rewinder (A), before the dispenser rocker (D, Figure 5) must be moved forwards/upwards by pulling out the knurled knob (C, Figure 5). 5. Adjust the position of pressure roller (D) with the clamping lever When using the pressure roller (E) in such a way that the roller and the label touch themselves...
-
Page 25: Options
Wipe-On Applicators Options Options 6.1 Product Sensor The 'product sensor' option is used for optical, contact-free registration of products in order to obtain input signals for the printing system. Figure 14 A = Reflector B = Connecting line C = Reflexion photocell NOTICE! When using reflection photocells, please observe that other light (e.g. - Page 26 Options Wipe-On Applicators Operating Manual 10.23...
-
Page 27: Environmentally-Friendly Disposal
It may only be organised, used and disposed of by the manufacturer. Valentin products accordingly labelled can therefore be returned to Carl Valentin GmbH. This way, you can be sure your old equipment will be disposed of correctly. - Page 28 Environmentally-Friendly Disposal Wipe-On Applicators Operating Manual 10.23...
-
Page 29: Index
WMX 5001 / 5101 / 5201 / 5301 ......21 presure brush WMX 5001 / 5101 / 5201 / 5301 ......22 dispensing angle, adjusting WMX 5001 / 5101 / 5201 / 5301 ..19, 20 displacement unit, adjusting ............... 17 environmentally-friendly disposal ............ - Page 30 Index Wipe-On Applicators unpacking ................... 13 wipe-on applicator, connecting ............14 Operating Manual 10.23...
Need help?
Do you have a question about the WMX 5001 and is the answer not in the manual?
Questions and answers