Pentair STA-RITE ecoselect enviroMAX 1500 Owner's Manual

Pentair STA-RITE ecoselect enviroMAX 1500 Owner's Manual

Variable speed pool pump

Advertisement

Quick Links

Variable Speed Pool Pump

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the STA-RITE ecoselect enviroMAX 1500 and is the answer not in the manual?

Questions and answers

Summary of Contents for Pentair STA-RITE ecoselect enviroMAX 1500

  • Page 1 Variable Speed Pool Pump...
  • Page 2: Table Of Contents

    Table of Contents Eco Select ® The Eco Select brand identifies our most eco-friendly products ® Page As the global leader in pool and spa equipment, we’ve made a strong commitment to develop and offer the Features and Benefits most environmentally responsible products available. Technical Information Model Data When you see the Eco Select...
  • Page 3: Features And Benefits

    Protection: Mains over voltage, mains under voltage, over ► Automation Connectivity - Connect control cable to com port and control pump seemlessly with a Pentair IntelliCenter or EasyTouch pool automation system. temperature, under temperature, locked rotor, over current, phase disconnect.
  • Page 4: Hydraulic Performance

    Technical Information Installation The pump must be installed and serviced by a suitably qualified person in Hydraulic Performance order to avoid hazard. Incorrectly installed or tested equipment may fail, causing severe injury or property damage. These instructions are a guide only. Should you the installer or owner of the product be unfamiliar with the correct installation or operation of this product you should contact a suitably qualified person for advice.
  • Page 5: Pool Outlets

    Installation Installation 3. Pool Outlets 5. Equipotential bonding The EnviroMax 1500 pump is double insulated to water circtuit. Check with local code requirements whether equipotential bonding is required. If equipotential bonding is required, connect all metal parts of the swimming pool or spa structure and to all electrical equipment, metal conduit, and metal piping in accordance with the wiring rules.
  • Page 6: Operation

    Operation Operation CONTROL PANEL OVERVIEW Control Panel Overview NEVER run pump dry. Running pump dry may damage seals, causing leakage and flooding. Fill pump with water before starting motor. Freezing conditions will damage the unit, as water expands as it freezes. Ensure that the EnviroMAX 1500 is located so that it is not prone to freezing, or ensure that the product is disconnected and dried of water during cold conditions.
  • Page 7: Setting Clock

    Operation Operation Custom Schedules Custom Schedules To customize the run schedule for your SuperFlo ® Press the “ 1” button again and the display will Activating and Deactivating the Time Clock Variable Speed Pump, the pump must be stopped. change to SPEED 1 duration. The “Duration” Custom Schedules To customize the run schedule for your SuperFlo ®...
  • Page 8: Custom Schedules

    Operation Operation Custom Schedules Operating the Pump White Running Use the “+” and “-” arrows to adjust the duration for SPEED 1 in hours and minutes. CAUTION Note: The duration parameter is adjusted in 15 minute increments. If power is connected to the pump motor, pressing any of the following Pressing the “1”...
  • Page 9: Keypad Lockout

    Priming Key lockout will not prevent the motor from being stopp the Start/Stop button. It will then be unable to be resta This pump is shipped with Priming mode ENABLED. Unless the Priming settings are changed in the menu, be aware keypad has been unlocked.
  • Page 10: Factory Reset

    Be sure that it is necessary before To perform a Factory Reset: has a sealed connector that can be used with Pentair External Control Wiring Kit (Pentair P/N 356324Z) to performing a Factory Reset, as the results are immediate.
  • Page 11: External Controls

    Figure 12. When there is a low voltage signal present on the Speed The wire included with the External Control Wiring Kit (Pentair P/N 353129Z) will need to be cut to length for the Digital Input line the pump will run the speed that is programmed for the speed that is being triggered.
  • Page 12 Call fan. a Pentair Service Agent immediately, to Note: If the pump has been stopped via the Note: If multiple low voltage triggers are present it will be resolved by this priority: Quick Clean, Speed 3, Start/Stop button, the pump will not run until the pump is turned back prevent damage to the motor.
  • Page 13: Troubleshooting

    ► Pump may be trying to push too high a column of water. If Should problems persist, contact your nearest Pentair Water Service Agent. so, a higher pressure pump is required.
  • Page 14: Servicing

    Troubleshooting Troubleshooting Servicing Troubleshooting guide Errors and Alarms To avoid dangerous or fatal electrical shock hazard, turn OFF power to pump and remove plug from power outlet before working on pump. If an alarm is triggered the drive’s LCD screen will display the fault code text and the EnviroMAX 1500 Variable Speed Pump will stop running.
  • Page 15 Troubleshooting Replacement Parts Servicing Shaft Seal Replacement Place seal plate face down on a flat surface and tap out white ceramic seal (see Figure 15). Figure 15 Figure 16 Remove the slinger from motor shaft and inspect damage or abrasion. Clean the seal plate’s seal cavity and the motor shaft.
  • Page 16 Replacement Parts Notes Description Part Number DIFFUSER See Diffuser & O-ring kit DIFFUSER & O-RING KIT (INCLUDES ITEM 1,11&12x7) 801423 IMPELLER 801427 O-RING- COLLAR UNION See Barrel Union Kit COLLAR UNION 2” SLIP See Barrel Union Kit COLLAR UNION 2” See Barrel Union Kit BARREL UNION KIT (INCLUDES 3, 4, &...
  • Page 17 Email: au.sales@pentair.com Web: www.pentairpool.com.au © Information contained here-in remains the property of Pentair Australia Pty Ltd. Any reproduction, display, publication, modification or distribution is strictly prohibited without the prior written permission of Pentair Australia Pty Ltd. Disclaimer: Every endeavour has been made to publish the correct details in this document. No responsibility will be taken for errors, omissions or changes in product descriptions, specifications.

Table of Contents