Table of Contents
Advertisement
ENGLISH
◆
Where splintering is to be minimised, e.g. when cutting
laminates, clamp a piece of plywood onto the top of the
workpiece.
◆
Support large panels to minimize the risk of blade
pinching and kickback. Large panels tend to sag under
their own weight.
◆
Supports must be placed under the panel on both si-
des, near the line of cut and near the edge of the panel
being cut.
◆
Never hold piece being cut in your hands or across your
leg.
◆
Secure the workpiece to a stable platform using
clamps. It is important to support the work properly
to minimize body exposure, blade binding, or loss of
control.
Maintenance
Your Stanley FatMax corded/cordless appliance/tool has
been designed to operate over a long period of time with
a minimum of maintenance. Continuous satisfactory operati-
on depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
◆
Switch off and unplug the appliance/tool.
◆
Or switch off and remove the battery from the appli-
ance/ tool if the appliance/tool has a separate battery
pack.
◆
Or run the battery down completely if it is integral and
then switch off.
◆
Unplug the charger before cleaning it. Your charger
does not require any maintenance apart from regular
cleaning.
◆
Regularly clean the ventilation slots in your appliance/
tool/ charger using a soft brush or dry cloth.
◆
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
◆
Regularly open the chuck and tap it to remove any dust
from the interior (when fi tted).
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fi tted:
◆
Safely dispose of the old plug.
◆
Connect the brown lead to the live terminal in the new
plug.
◆
Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the fi tting instructions supplied with good quality
plugs.
Recommended fuse: 13 A.
8
Protecting the environment
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be recove-
red or recycled, reducing demand for raw materials.
Please recycle electrical products and batteries according
to local provisions. Further information is available at
www.2helpU.com
Technical data
Input voltage
V
AC
Power input
W
No-load speed
Min
Max. depth of cut
mm
Blade diameter
mm
Blade bore
mm
Blade tip width
mm
Weight
kg
Level of sound pressure according to EN 60745:
Sound pressure (L
) 89,0 dB(A), uncertainty (K) 3 dB(A)
pA
Sound power (L
) 100 dB(A), uncertainty (K) 3 dB(A)
WA
Vibration total values (triax vector sum) according to EN 60745:
Vibration emission value (ah,w) 2.6 m/s
EC declaration of conformity
MACHINERY DIRECTIVE
FME301 - Circular saw
Stanley Europe declares that these products described
under "technical data" are in compliance with:
2006/42/EC, EN60745-1:2010, EN60745-2-5:2010
These products also comply with Directive 2014/30/EU and
2011/65/EU.
For more information, please contact Black & Decker at the
following address or refer to the back of the manual.
The undersigned is responsible for compilation of the
technical fi le and makes this declaration on behalf of
Black & Decker.
FME301
-1
3.9 (4.31 with blade)
, uncertainty (K) 1.5 m/s
(cutting wood)
2
2
230
1650
5500
66
190
16
1.8
Advertisement
Table of Contents
