Advertisement
Quick Links
Service Instructions
Hoover PowerDash Pet- PowerDash Pet Complete
PowerDash Pet Model #: FH50710V, FH50700UPC, FH50700, FH50710CN, FH50750, FH50700PDI
GL, FH50700FDI, FH50700CDI, FH50702, FH50703CDI, FH50700V, FH50750V, FH50750PDI,
FH50703VCD, FH50704, FH50704V, FH50711CN, FH50711V, FH50751, FH50751V, FH50751PDI,
FH50751VPD, FH50704FDI, FH50704VFD, FH50701CDI, FH50740CDI.
PowerDash Pet Complete Model #: FH50704, FH50711CN, FH50751, FH50751PDI, FH50704FDI,
FH50701CDI, FH50740CDI, FH50704V, FH50711V, FH50751V, FH50751VPD, FH50704VFD,
FH50701VCD, FH50740VCD, FH55050PC, FH55010, FH55000, FH55050V, FH55010V, FH55000V
TO VIEW PARTS SCHEMATICS PLEASE VISIT "PARTS CATALOG" THROUGH THE DEALER
PORTAL HOME PAGE.
Advertisement
Related Manuals for Hoover PowerDash Pet FH50710V
Summary of Contents for Hoover PowerDash Pet FH50710V
- Page 1 Service Instructions Hoover PowerDash Pet- PowerDash Pet Complete PowerDash Pet Model #: FH50710V, FH50700UPC, FH50700, FH50710CN, FH50750, FH50700PDI GL, FH50700FDI, FH50700CDI, FH50702, FH50703CDI, FH50700V, FH50750V, FH50750PDI, FH50703VCD, FH50704, FH50704V, FH50711CN, FH50711V, FH50751, FH50751V, FH50751PDI, FH50751VPD, FH50704FDI, FH50704VFD, FH50701CDI, FH50740CDI. PowerDash Pet Complete Model #: FH50704, FH50711CN, FH50751, FH50751PDI, FH50704FDI,...
- Page 2 Troubleshooting A. Unit Leaking 1. The clean and dirty tank are not placed properly or might be filled. (1) Check to ensure all tanks are properly filled or empty (dirty water tank cannot be over the max limit, to prevent leaking through the motor) (2) Ensure the tanks are firmly placed into the unit and there are no gaps or looseness.
- Page 3 tanks are seated firmly, turn the unit on, and recline the handle. Push the unit forward continuously about 3-4 times or until water comes out of the bottom. Power ON again. Unit may need to be reset. To reset the PowerDash, unplug it from the wall. Remove the nozzle cover and take out the brushes.
- Page 4 3. The debris filter is dirty (1) Remove the debris filter, located under the Dirty Water Tank, wipe it clean. 4. There is a clog in the tool at the end of the hose. (1) Remove the tool and clear out any debris. 5.
- Page 5 3. The belt might be broken. (You may experience a burning smell, or a high pitch sound) (1) Remove the bottom plate of the unit and remove the brushroll.
- Page 6 (2) Place the new belt on the motor shaft (3) Position the non-belt side of the roll into the notch it belong to. (4) Carefully stretch the belt to position the other en cap into the notch (5) Replace the belt cover and secure the 6 screws to the plate. See below F.
- Page 7 (3) The thermal protector might have activated. The unit does this to prevent damage from overheating. (a) Unplug the unit from the outlet. (b) Clean the dirty and clean water tanks (c) Make sure to clean the nozzle and brushroll too. (d) Allow the unit to cool down for up to 30 minutes.