Advertisement
ComfortStar
SPLIT TYPE AIR CONDITIONER
INSTRUCTION MANUAL
＼
CLA12CA-T
CLA12CD-T
CLA18CD-T
CLA24CD-T
This instruction manual contains important information and
recommendations that we would ask you to comply with to
obtain best results from air conditioner.
Thank you once again.
www.comfortstarusa.com
®
CIP12CA-HT
CIP12CD-HT
CIP1 BCD-HT
CIP24CD-HT
丿
Advertisement
Table of Contents
Related Manuals for ComfortStar CLA12CA-T
Summary of Contents for ComfortStar CLA12CA-T
- Page 1 ® ComfortStar SPLIT TYPE AIR CONDITIONER INSTRUCTION MANUAL ＼ 丿 CLA12CA-T CIP12CA-HT CLA12CD-T CIP12CD-HT CLA18CD-T CIP1 BCD-HT CLA24CD-T CIP24CD-HT This instruction manual contains important information and recommendations that we would ask you to comply with to obtain best results from air conditioner.
-
Page 2: Table Of Contents
CONTENTS S A FET Y PR E C A U TIO N S ........................1 N A M E OF PA R TS ..........................4 R E M O TE C O N T RO L ........................... 6 OPERATIO N I N ST RU C TI O N S ......................13 I N STA LL ATIO N PR E C A U TIO N S ...................... -
Page 3: Safety Precautions
SAFETY PRECAUTIONS SAFETY RULES AND RECOMMENDATIONS FOR THE INSTALLER 1. Read this guide before installing and using the appliance. 2. During the installation of the indoor and outdoor units, access to the working area should be forbidden to children. Unforeseeable accidents could happen. 3. - Page 4 SAFETVPRECAUTlONS SAFE TY RULES AND RECOMMENDATIONS FOR THE INSTALLER 。 not try to install the conditioner alone, always contact specialized technical personnel. 20. Cleaning and maintenance must be carried out by specialized technical personnel. In any case disconnect the appliance from the mains electricity supply before carrying out any cleaning or maintenance.
- Page 5 SAFETYPRECAUTlONS SAFETY RULES AND PROHIBITIONS 1. Do not bend, tug or compress the power cord since this could damage it. Electrical shocks or fire are probably due to a damaged power cord. Specialized technical personnel only must replace a damaged power cord. .
-
Page 6: | Nameofparts
| NAMEOFPARTS lndoor Unit Mounting plate Front panel Emergency button Air deflector and flap Refrigerant connecting pipe Outdoor Unit Air inlet Wiring cover Air outle Drainage pipe Connection wiring Valve protective cover Gas valve (Low pressure valve) Liquid valve (High pressure valve) With the protective cover removed Note: This figure shown may be different from the actual object. - Page 7 NAMEOFPARTS lndoor Display － － l l l l 4 � I 勹 I , 0 <b － － — 门 厂 J — — ． 仁 勹 Function 。 仁U Indicator for Timer, temperature and Error codes. Lights up during Timer operation. SLEEP mode The symbol appears when the unit is turned on , and disappear 十...
-
Page 8: Remotecontrol
REMOTECONTROL Remote control DISPLAY Symbols Meaning 。 Battery indicator O帝6%＊夺ICI 会 ° Auto Mode 00 0 巳Cl.Cl h 需 , ,r 争 11111心 Cooling Mode 杂 3划王；但8HO守 Dry Mode ＠三三三 `” •, ,,. ＇ Fan only Mode ,---8---, 三巨匠 -、 乡 o 1、... - Page 9 REMOTECONTROL Button Function ＠ To turn on/off the air conditioner . ＾ To increase temperature, or Timer setting hours. To decrease temperature, or Timer setting hours. To select the mode of operation (AUTO, COOL, DRY, FAN, HEAT). MODE To activate/deactivate the ECO function. °...
- Page 10 REMOTE CONTROL Replacement of Batteries Remove the battery cover plate from the rear of the remote control, by sliding it in direction as the arrow. Install the batteries according the direction(+ and -)shown on the Remo Control. 把 Reinstall the battery cover by sliding it into place. 心...
- Page 11 REMOTECONTROL 三 COOLING MODE HEATING MODE The cooIing function a||ows the air The heating function allows the air 翠 HEAT conditioner to cool the room and conditioner to heat the room. reduce Air humidity at the same To activate the heating function (HE AT ) , press the time.
- Page 12 REMOTECONTROL TIMER function---- TIMER ON SWING function -…习 。 ＾ I l � v< 、 automatica1|y switch on the SWING 么 〉 霖 appliance. SWING[� When the unit is switch-off, you can set the 1. Press the button SWING to activate the louver, 马...
- Page 13 REMOTECONTROL 三 MUTE function ECO function 尸 In this mode the app|iance automatically sets the operation to save energy. 1. Press芦button to active this function, 晤习 and，货will appears on the remote display. Press the button, the 匝appears on the · Do it again to deactivate this function.
- Page 14 REMOTECONTROL Gentle Wind function (Optional) SELF-CLEAN function (Optional) Only optional for some heating pump inverter 1. Turn on the indoor unit, and change to COOL appliance. mode, then long press阿and麟button To active this function, turn off the indoor unit together 3 seconds to active this function,；三 二...
-
Page 15: Operatio N I N St Ru C Ti O N S
| OPERATlON INSTRUCTlONS Attempt to use the air conditioner under the temperature beyond the specified range may cause the air conditioner protection device to start and the air conditioner may fail to operate. Therefore, try to use the air conditioner in the following temperature conditions. Fixed air conditioner: 三Temoera D r y... -
Page 16: I N Sta Ll Atio N Pr E C A U Tio N S
lNSTALLATlON PRECAUTlONS Pi-erant Inverter Models Capacity (Btu/h) 9K-12K 18K-24K 30K-36K Length of pipe with standa d charge 5m/16ft 5m/16ft 5m/16ft 5m/16ft 5m/16ft 5m/16ft 『 Length of pipe with standa d charge (Like: North American, etc.) 7.Sm/24ft 7.Sm/24ft 7.Sm/24ft 7.5m/24ft 7.Sm/24ft 7.Sm/24ft 『... -
Page 17: I N D Oor U N It I N St A Ll At Io N
| lNDOORUNlTINSTALLATlON SteQl: Select Installation location 1.1 Ensure the installation complies with the installation minimum dimensions (defined below) and meets the minimum and maximum connecting piping length and maximum change in elevation as defined in the System Requirements section. 1.2 Air inlet and outlet will be clear of obstructions, ensuring proper airflow throughout the room. 1.3 Condensate can be easily and safely drained. - Page 18 | lNDOORUNlTINSTALLATlON Ste� Plate 2.1 Take the mounting plate from the back of indoor unit. 2.2 Ensure to meet the minimum installation dimension requirements as step 1, according to the size of mounting plate, determine the position and stick the mounting plate close to the wall. 2.3 Adjust the mounting plate to a horizontal state with a spirit level, then mark out the screw hole positions on the wall.
- Page 19 | lNDOORUNlTINSTALLATlON Step4: Connecting Refrigerant Pipe 4.1 According to the wall hole position, select the appropriate piping mode. There are three optional piping modes for indoor units as shown in the figure below: In Piping Mode 1 or Piping Mode 3, a notch should be made by using scissors to cut the plastic sheet of piping outlet and cable outlet on the corresponding side of the indoor unit.
- Page 20 | lNDOORUNlTINSTALLATlON Step5: Connect Drainage Hose 5.1 Adjust the drainage hose(if applicable) In some model, both sides of the indoor unit are provided with drainage ports, you can choose one of them to attache the drainage hose. And plug the unused drain port with the rubber attached in one of the ports.
- Page 21 lNDOORUNlTINSTALLATlON Step7: Wrap Pipin g and Cable After the refrigerant pipes, connecting wires and drainage hose are all installed, in order to save space, protect and insulate them, it must be bundle with insulating tape before passing them through the wall hole. 7.1 Arrange the pipes ,cables and drainage hose well as the following picture.
-
Page 22: Outdoor U N It I N Sta Ll Atio N
OUTDOORUNlTINSTALLATlON Step1: Select lnstallation Location Select a site that allows for the following: 1.1 Do not install the outdoor unit near sources of heat, steam or flammable gas. 1.2 Do not install the unit in too windy or dusty places. 1.3 Do not install the unit where people often pass. - Page 23 OUTDOORUNlTINSTALLATlON Step4: lnstall Wiring 4.1 Use a phillips screwdriver to unscrew wiring cover, grasp and press it down gently to take it down. 4.2 Unscrew the cable clamp and take it down. 4.3 According to the wiring diagram pasted inside the wiring cover, connect the connecting wires to the corresponding terminals, and ensure all connections are firmly and securely.
- Page 24 OUTDOORUNlTINSTALLATlON Step6: Vacuum Pumping 6.1 Use a spanner to take down the protective caps from the service port, low pressure valve and high pressure valve of the outdoor unit. 6.2 Connect the pressure hose of manifold gauge to the service port on the outdoor unit low pressure valve.
-
Page 25: Test Operatio N
TESTOPERATlON lnseections Before Test Run Do the following checks before test run. Description Inspection method • Check whether the power supply voltage complies with specification. Electrical • Check whether there is any wrong or missing connection between the safety inspection power lines, signal line and earth wires. - Page 26 TESTOPERATlON Test Run Instruction 1. Turn on the power supply. 2. Press the ON/OFF button on the remote controller to turn on the air conditioner. 3. Press the Mode button to switch the mode COOLING and HEATING. In each mode set as below: COOLING-Set the lowest temperature HEATING-Set the highest temperature 4.
-
Page 27: Maintenance
MAlNTENANCE • When cleaning, you must shut down the machine and cut off the power supply for more than 5 minutes. • Under no circumstances should the air conditioner be flushed with water. 1 • Volatile liquid (e.g. thinner or gasoline) will damage the air conditioner, so only use soft W arnin g 1 dry c|oth or wet c|oth dipped with neutra| detergent to c|ean the air conditioner. - Page 28 TROUBLESHOOTlNG POSSIBLE CAUSES MALFUNCTION Power failure/plug pulled out. Damaged indoor/outdoor unit fan motor. Faulty compressor thermomagnetic circuit breaker. Faulty protective device or fuses. The appliance does Loose connections or plug pulled out. not operate It sometimes stops operating to protect the appliance. Voltage higher or lower than the voltage range.
- Page 29 TROUBLESHOOTlNG ERROR CODE ON THE DISPLAY In case of error, the display on the indoor unit shown the following error codes: Display Description of the trouble Indoor room temperature sensor fault Indoor pipe temperature sensor fault Outdoor pipe temperature sensor fault E '-I Refrigerant system leakage or fault Malfunction of indoor fan motor...
Need help?
Do you have a question about the CLA12CA-T and is the answer not in the manual?
Questions and answers