BAFANG DP C263.CAN User Manual
  1. Manuals
  2. Brands
  3. BAFANG Manuals
  4. Measuring Instruments
  5. DP C263.CAN
  6. User manual

BAFANG DP C263.CAN User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
7 USER MANUAL FOR
DP C263.CAN
CONTENT
BF-UM-C-DP C263-EN May 2022
2
2
3
3
3
4
4
5
5
5
5
1
6
6
7
7
7
8
8
9
12
16

Advertisement

Table of Contents
loading

Related Manuals for BAFANG DP C263.CAN

Summary of Contents for BAFANG DP C263.CAN

  • Page 1: Table Of Contents

    7 USER MANUAL FOR DP C263.CAN CONTENT 7.1 Important Notice 7.6.4 Walk Assistance 7.2 Introduction of Display 7.6.5 Selection of Mode 7.3 Product Description 7.6.6 Service 7.6.7 Battery Capacity Indication 7.3.1 Specifications 7.6.8 Bluetooth Function 7.3.2 Functional Overview 7.7 Settings 7.4 Display Information...

  • Page 2: Important Notice

    • Do not clean the display with a steam jet, high-pressure cleaner or water hose. 7.2 INTRODUCTION OF DISPLAY • Model: DP C263.CAN BUS • The label marking is as follow: • The housing material is ABS, the cover and...

  • Page 3: Product Description

    7.3 PRODUCT DESCRIPTION 7.3.2 Functional Overview 7.3.1 Specifications • Speed indication (including the real-time • Operating temperature: -20℃~45℃ speed, max. speed and average speed) • Storage temperature: -20℃~60℃ • Unit switching between km and mile. • Waterproof: IP65 • Battery capacity indication •...

  • Page 4: Display Information

    7.4 DISPLAY INFORMATION Bluetooth indication Service indication Speed display in real-time Speed unit indication Mode selection: single-trip distance (TRIP), total distance ODO, maximum speed (MAX), ave- rage speed (AVG), remaining distance (RANGE), energy consumption (CALORIES), time (TIME). (Note: same function needs the Controller supports).

  • Page 5: Normal Operation

    7.6 NORMAL OPERATION 7.6.1 Switching the System ON/OFF Press and hold (>2S) to power on the display, the HMI begin to show the boot up LOGO. Press and hold (>2S) again can power off the HMI. 7.6.2 Selection of Support Levels When HMI power on, briefly press (<0.5s) to select the assistance level (the number of assistance level needs to be adapted to controller), The lowest level is Level 0, the highest Level is 5.

  • Page 6: Walk Assistance

    7.6.4 Walk Assistance When your Pedelec is motionless, briefly press button until the Walk assistance indicator displayed. At this point, long press button, the Pedelec enters the walk assistance mode, the in- dicator will flash. If release the button will stop this, if no any operations within 5s will automatically return to 0 level.

  • Page 7: Service

    1 HZ. 7.6.8 Bluetooth Function This display can be connected to the Bafang Go APP through Bluetooth. This display is equipped with the OAT function, which can provide firmware update for other parts. BF-UM-C-DP C263-EN May 2022...

  • Page 8: Settings

    7.7 SETTINGS After the HMI powered on, briefly press 7.7.1.1 “Trip Reset”---set reset function for “Mode” button two times to enter into the single-trip “Setting”. Briefly press (<0.5s) to Briefly press to select “Trip Reset”, select and then briefly press (<0.5S) “Mode” and then briefly press “Mode”...

  • Page 9: Information" Interface

    7.7.1.3 “Brightness”--- set backlight 7.7.1.5 “Assist Mode”---set assistance level brightness Briefly press to select “Assist Briefly press to select “Brightness”, Mode”, and then briefly press “Mode” to en- and then briefly press “Mode” to enter into ter into the item. Select the assistance level the item.
  • Page 10 7.7.2.1 View “Wheel Size” communication function, you won’t see any data from battery. Briefly press to select ” Wheel Size”, and then briefly press “Mode” to view the wheel size default, then briefly press “Mode” to exit back to the "Information" interface.
  • Page 11 7.7.2.4 View “Display Info” Briefly press to select ”Display Info”, and then briefly press “Mode” to view it, briefly press to view“Hardware Ver” or “Software Ver”, then briefly press “Mode” to exit back to the "Information" interface. 7.7.2.7 View “Error Code” Briefly press to select ”Error Code”, and then briefly press “Mode”...

  • Page 12: Error Code Definition

    7.8 ERROR CODE DEFINITION The HMI can show the faults of Pedelec. When a fault is detected, one of the following error codes will be indicated on the position of speed display. Note: Please read carefully the description of the error code. When the error code appears, please first restart the system.
  • Page 13 Error Declaration Troubleshooting 1. Check all connectors from the battery are correctly connected to the motor. Error with the temperature sensor inside of the battery 2. If the problem still occurs, please change the Battery. 1. Allow the pedelec to cool down and restart the The protection temperature system.
  • Page 14 Error Declaration Troubleshooting 1. Check that all connections are connected correctly. 2. Please connect the pedelec to the BESST system to see if speed signal can be read by the BESST tool. Speed signal of the torque 3. Change the Display to see if the problem is solved. sensor has an error 4.
  • Page 15 Error Declaration Troubleshooting Using the BESST tool update the controller to see if WDT circuit is faulty this resolves the problem. If not, please change the controller or contact your supplier. Total voltage from the battery is Please change the battery. too high Total voltage from the battery is Please Charge the battery.

  • Page 16: Warn Code Definition

    7.9 WARN CODE DEFINITION Warn Declaration Troubleshooting Torque sensor's initialization is Restart the system and note not to step on the crank abnormal. hard when restarting. BF-UM-C-DP C263-EN May 2022...

Table of Contents