Related Manuals for BAFANG DP C260.CAN
Summary of Contents for BAFANG DP C260.CAN
-
Page 1: Table Of Contents
7 USER MANUAL FOR DP C260.CAN CONTENT 7.1 Important Notice 7.6.3 Selection Mode 7.2 Introduction of Display 7.6.4 Headlights / backlighting 7.3 Product Description 7.6.5 Walk Assistance 7.6.6 Battery Capacity Indication 7.3.1 Specifications 7.6.7 SERVICE 7.3.2 Functions Overview 7.7 Settings 7.4 Display Information... -
Page 2: Important Notice
• Do not clean the display with a steam jet, high-pressure cleaner or water hose. 7.2 INTRODUCTION OF DISPLAY • Model: DP C260.CAN BUS • The label marking is as follows: • The housing material is ABS, the window is... -
Page 3: Product Description
7.3 PRODUCT DESCRIPTION 7.3.2 Functional Overview 7.3.1 Specifications • Speed indication (including the real-time • Operating temperature: -20℃~45℃ speed, max. speed and average speed) • Storage temperature: -20℃~50℃ • Unit switching between km and mile. • Waterproof: IP65 • Battery capacity indication •... -
Page 4: Display Information
7.4 DISPLAY INFORMATION Headlight indication Speed display in real-time Mode selection: single-trip distance (TRIP), total distance ODO, maximum speed (MAX), average speed (AVG), remaining distance (RANGE), energy consumption (CALORIES), time (TIME). (Note: same function needs the Controller supports). Support level and walk assistance indication Battery capacity indication “Service”indication. -
Page 5: Normal Operation
7.6 NORMAL OPERATION 7.6.1 Switching the System ON/OFF Press and hold (>2S) to power on the display, the HMI begin to show the boot up LOGO. Press and hold (>2S) again can power off the HMI. If the "automatic shutdown" time is set to 5 minutes (it can be set in function "Auto Off"), the HMI will be automatically turned off within this set time, When it is not operated. -
Page 6: Selection Mode
7.6.3 Selection Mode Briefly press “Mode” button (<0.5s) to view the different mode and information. 1. System with torque sensor, circularly show single trip distance (Trip,km) → total distance (ODO,km) → maximum speed (MAX,km/h) → average speed (AVG,km/h) → remaining distance (RANGE,km) → cadence (CADENCE) →... -
Page 7: Walk Assistance
7.6.5 Walk Assistance When your Pedelec is motionless, briefly press button until the Walk assistance indicator displayed. At this point, long press button, the Pedelec enters the walk assistance mode, the in- dicator will flash. If release the button will stop this, if no any operations within 5s will automatically return to 0 level. -
Page 8: Settings
7.7 SETTINGS After the HMI powered on, briefly press 7.7.1.1 “TRIP Reset”---set reset function “Mode” button two times to enter into the for single-trip “SETTING”. Briefly press (<0.5s) to Briefly press to select “TRIP Reset”, select and then briefly press (<0.5S) “Mode” and then briefly press “Mode”... -
Page 9: Information" Interface
and then briefly press “Mode” to enter into as “3”/“5”/“9”, then briefly press “Mode” to the item. Select the percentage as “100%”/ save and exit back to the "Setting" interface. “75%”/“50%”/“30%”/“10%”, then briefly press “Mode” to save and exit back to the "Setting"... - Page 10 7.7.2.1 View “Wheel Size” communication function, you won’t see any data from battery. Briefly press to select ” Wheel Size”, and then briefly press “Mode” to view the wheel size default, then briefly press “Mode” to exit back to the "Information" interface.
- Page 11 7.7.2.4 View “Display Info” 7.7.2.6 View “Torque Info” Briefly press to select ”Display Briefly press to select ”Torque Info”, and then briefly press “Mode” to view Info”, and then briefly press “Mode” to view it, briefly press to view“Hardware it, briefly press to view“Hardware Ver”...
-
Page 12: Error Code Definition
7.8 ERROR CODE DEFINITION The HMI can show the faults of Pedelec. When a fault is detected, one of the following error codes will be indicated. Note: Please read carefully the description of the error code. When the error code appears, please first restart the system. - Page 13 Error Declaration Troubleshooting 1. Turn off the system and let the pedelec cool The protection temperature inside down. the controller has reached its maxi- 2. If the problem persists, please contact your mum protection value retailer. Error with the temperature sensor Please contact your retailer.
- Page 14 Error Declaration Troubleshooting Detection circuit for 15V has an error Please contact your retailer. Detection circuit on the keypad has Please contact your retailer. an error WDT circuit is faulty Please contact your retailer. Total voltage from the battery is too Please contact your retailer.