Related Manuals for BAFANG DP C262.CAN BUS
Summary of Contents for BAFANG DP C262.CAN BUS
-
Page 1: Table Of Contents
7 USER MANUAL FOR DP C262.CAN CONTENT 7.1 Important Notice 7.6.4 Headlights / backlighting 7.2 Introduction of Display 7.6.5 Walk Assistance 7.3 Product Description 7.6.6 Battery Capacity Indication 7.6.7 Service 7.3.1 Specifications 7.7 Settings 7.3.2 Functional Overview 7.4 Display Information 7.7.1 “Setting”... -
Page 2: Important Notice
• Do not clean the display with a steam jet, high-pressure cleaner or water hose. 7.2 INTRODUCTION OF DISPLAY • Model: DP C262.CAN BUS • The label marking is as follow: • The housing material is ABS, the cover and... -
Page 3: Product Description
7.3 PRODUCT DESCRIPTION 7.3.2 Functional Overview 7.3.1 Specifications • Speed indication (including the real-time • Operating temperature: -20℃~45℃ speed, max. speed and average speed) • Storage temperature: -20℃~60℃ • Unit switching between km and mile. • Waterproof: IP65 • Battery capacity indication •... -
Page 4: Display Information
7.4 DISPLAY INFORMATION Headlight indication Speed display in real-time Mode selection: single-trip distance (TRIP), total distance ODO, maximum speed (MAX), average speed (AVG), remaining distance (RANGE), energy consumption (CALORIES), time (TIME). (Note: same function needs the Controller supports). Support level and walk assistance indication Battery capacity indication “Service”indication. -
Page 5: Normal Operation
7.6 NORMAL OPERATION 7.6.1 Switching the System ON/OFF Press and hold (>2S) to power on the display, the HMI begin to show the boot up LOGO. Press and hold (>2S) again can power off the HMI. Welcome interface 7.6.2 Selection of Assistance Levels When HMI power on, briefly press (<0.5s) or to select the assistance level (the number of... -
Page 6: Selection Of Mode
7.6.3 Selection of Mode Briefly press “Mode” button (<0.5s) to view the different mode and information. 1. System with torque sensor, circularly show single trip distance (Trip,km) → total distance (ODO,km) → maximum speed (MAX,km/h) → average speed (AVG,km/h) → remaining distance (RANGE,km) → cadence (CADENCE) →... -
Page 7: Walk Assistance
7.6.5 Walk Assistance When your Pedelec is motionless, briefly press button until the Walk assistance indicator displayed. At this point, long press button, the Pedelec enters the walk assistance mode, the in- dicator will flash. If release the button will stop this, if no any operations within 5s will automatically return to 0 level. -
Page 8: Settings
7.7 SETTINGS After the HMI powered on, briefly press 7.7.1.1 “Trip Reset”---set reset function for “Mode” button two times to enter into the single-trip “Setting”. Briefly press (<0.5s) to Briefly press to select “Trip Reset”, select and then briefly press (<0.5S) “Mode” and then briefly press “Mode”... - Page 9 7.7.1.3 “Brightness”--- set backlight 7.7.1.5 “Assist Mode”---set assistance level brightness Briefly press to select “Assist Briefly press to select “Brightness”, Mode”, and then briefly press “Mode” to en- and then briefly press “Mode” to enter into ter into the item. Select the assistance level the item.
-
Page 10: Information" Interface
7.7.2 “Information” interface In Setting interface, briefly press (<0.5S) to select “Information” and then briefly press (<0.5S) “Mode” to confirm and enter into “Information”. 7.7.2.3 View “Battery Info.” Briefly press to go to “Battery Info.”, and then briefly press “Mode” to enter, then briefly press “+”... - Page 11 Code Code Definition Unit Current temperature ℃ Total voltage Average current Remaining capacity Battery capacity of Full charged 7.7.2.5 View “Ctrl Info” Briefly press to select ”Ctrl Info”, Relative Charge in percentage and then briefly press “Mode” to view it, briefly press to view“Hardware Ver”...
- Page 12 7.7.2.8 View “Warn Code” Briefly press to select "Warn Code", and then briefly press "Mode" to view it, briefly press to view message of warning for last ten times by “W-Code0” to “W-Code9”, then briefly press “Mode” to exit back to the "Information" interface. 7.7.2.7 View “Error Code”...
-
Page 13: Error Code Definition
7.8 ERROR CODE DEFINITION The HMI can show the faults of Pedelec. When a fault is detected, one of the following error codes will be indicated on the position of speed display. Note: Please read carefully the description of the error code. When the error code appears, please first restart the system. - Page 14 Error Declaration Troubleshooting 1. Check all connectors from the battery are correctly connected to the motor. Error with the temperature sensor inside of the battery 2. If the problem still occurs, please change the Battery. 1. Allow the pedelec to cool down and restart the The protection temperature system.
- Page 15 Error Declaration Troubleshooting 1. Check that all connections are connected correctly. 2. Please connect the pedelec to the BESST system to see if speed signal can be read by the BESST tool. Speed signal of the torque 3. Change the Display to see if the problem is solved. sensor has an error 4.
- Page 16 Error Declaration Troubleshooting Using the BESST tool update the controller to see if WDT circuit is faulty this resolves the problem. If not, please change the controller or contact your supplier. Total voltage from the battery is Please change the battery. too high Total voltage from the battery is Please Charge the battery.
-
Page 17: Warn Code Definition
7.9 WARN CODE DEFINITION Warn Declaration Troubleshooting Torque sensor's initialization is Restart the system and note not to step on the crank abnormal. hard when restarting. BF-UM-C-DP C262-EN November 2019...