Hitachi PSC-A128EX3 Operation Manual
Hitachi PSC-A128EX3 Operation Manual

Hitachi PSC-A128EX3 Operation Manual

Air conditioner managing system remote access
Hide thumbs Also See for PSC-A128EX3:

Advertisement

Quick Links

Operation Manual
HITACHI Air Conditioner
Managing System
Remote Access
Model: PSC-A128EX3
Thank you for choosing our Air Conditioner
Managing System.
● Please keep this manual in a safe place.
● If you have any questions or concerns,
please contact distributor or your dealer.
IMPORTANT:
READ AND UNDERSTAND
THIS MANUAL BEFORE USING
THIS CENTRAL CONTROLLER.
KEEP THIS MANUAL FOR
FUTURE REFERENCE.
A12124920A

Advertisement

Table of Contents
loading

Summary of Contents for Hitachi PSC-A128EX3

  • Page 1 Operation Manual HITACHI Air Conditioner Managing System Remote Access Model: PSC-A128EX3 Thank you for choosing our Air Conditioner Managing System. ● Please keep this manual in a safe place. ● If you have any questions or concerns, please contact distributor or your dealer. IMPORTANT: READ AND UNDERSTAND THIS MANUAL BEFORE USING THIS CENTRAL CONTROLLER. KEEP THIS MANUAL FOR FUTURE REFERENCE.
  • Page 3: Table Of Contents

    TABLE OF CONTENTS 1. Safety Summary ........................2 2. System Configuration ....................... 6 3. About This Manual ........................7 4. Preparation ..........................7 4.1 Test Run ........................... 7 4.2 PC Specification (prepared on site) .................. 7 4.3 Network Environment ....................... 8 4.3.1 Connecting the remote PC with the dedicated LAN ........... 8 4.3.2 Connecting the remote PC with the existing LAN ............8 4.3.3 Using the remote PC through internet ................ 8 4.3.4 Changing IP Address of PC for Remote Access software ........
  • Page 4: Safety Summary

    1. Safety Summary Important Notice ● HITACHI pursues a policy of continuing improvement in design and performance in its products. As such, HITACHI reserves the right to make changes at any time without prior notice. ● HITACHI cannot anticipate every possible circumstance that might involve a potential hazard. ● Central Station EX is designed for standard air conditioning applications only. Do not use this product for anything other than the purposes for which it was intended for. ● The installer and system specialist must safeguard against leakage in accordance with local pipefitter and electrical codes. The International Organization for Standardization: (ISO 5149) or European Standard (EN 378) may be applicable, if local regulations are not. No part of this manual may be reproduced in any way without the expressed written consent of HITACHI. ● If you have questions, please contact your distributor or dealer. ● This manual provides descriptions, and basic and advanced information to maintain and service Central Station EX which applies as well for other models. ● This manual should be considered a permanent part of the air conditioning equipment and should remain with the air conditioning equipment. Product Inspection upon Arrival 1. Upon receiving this product, inspect it for any damages incurred in transit. Claims for damage, either apparent or concealed, should be filed immediately with the shipping company. 2. Check the model number, electrical characteristics (power supply, voltage, and frequency rating), and any accessories to determine if they agree with the purchase order. 3. The standard utilization for Central Station EX is explained in these instructions. Do not use of this equipment for purposes other than what it designed for. 4. Please contact your local agent or contractor as any issues involving installation, performance, or maintenance arise. Liability does not cover defects originating from unauthorized modifications...
  • Page 5 Signal Words Indicates a hazardous situation that, if not avoided, could result in death or serious injury. Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury. Indicates information considered important, but not hazard-related (for example, messages relating to property damage). General Precautions To reduce the risk of serious injury or death, read these instructions thoroughly and follow all warnings or cautions included in all manuals that accompanied the product and are attached to the unit. Refer back to these safety instructions as needed. ● This system, including Remote Access, should be installed by personnel certified by HITACHI. Personnel must be qualified according to local, state, and national building and safety codes and regulations. Incorrect installation could cause leaks, electric shock, fire or explosion. In areas where Seismic ‘’Performance requirements are specified, the appropriate measures should be taken during installation to guard against possible damage or injury that might occur in an earthquake. If the product is not installed correctly, injuries may occur due to a falling product. ● Use appropriate Personal Protective Equipment (PPE), such as gloves and protective goggles and, where appropriate, have a gas mask nearby. Also use electrical protection equipment and tools suited for electrical operation purposes. Keep a wet cloth and a fire extinguisher nearby during brazing. Use care in handling, rigging, and setting of bulky equipment. ● When transporting, be careful when picking up, moving and mounting these units. Although the unit may be packed using plastic straps, do not use them for transporting the unit from one location to another.
  • Page 6 ● When installing Central Station EX in a hospital or other facility where electromagnetic waves are generated from nearby medical and/or electronic devices, be prepared for noise and electronic interference Electromagnetic Interference (EMI). Do not install where the waves can directly radiate into the electrical box, controller cable, or controller. Inverters, appliances, high-frequency medical equipment, and radio communications equipment may cause the product to malfunction. The operation of the product may also adversely affect these same devices. Install the product at least 3m away from such devices. ● When a wireless controller is used, locate it at a distance of at least 1 meter between the indoor unit and electric lighting. If not, the receiver part of the unit may have difficulty receiving operation commands. ● Do not install the unit in any location where animals and plants can come into direct contact with the outlet air stream. Exposure could adversely affect the animals and plants. ● Do not install the unit in any place where oil can seep onto the units, such as table or seating areas in restaurants, and so forth. For these locations or social venues, use specialized units with oil-resistant features built into them. In addition, use a specialized ceiling fan designed for restaurant use. These specialized oil-resistant units can be ordered for such applications. However, in places where large quantities of oil can splash onto the unit, such as a factory, even the specialized units cannot be used. These products should not be installed in such locations. Installation Precautions Take the following precautions to reduce the risk of electric shock, fire or explosion resulting in serious injury or death: ● When installing Central Station EX into… ▫ A wall: Make sure the wall is strong enough to hold the product’s weight. It may be necessary to construct a strong wood or metal frame to provide added support. ▫ A room: Properly insulate any refrigerant tubing run inside a room to prevent “sweating” that can cause dripping and water damage to wall and floors. ● Do not install Central Station EX in the following places. Doing so can result in an explosion, fire, damage, corrosion, or product failure. ▫ Explosive or flammable atmosphere ▫ Where a fire, oil, steam or powder can directly enter the unit, such as nearby or above a kitchen stove.
  • Page 7 Electrical Precautions Take the following precautions to reduce the risk of electric shock, fire or explosion resulting in serious injury or death. ● Highly dangerous electrical voltages are used in this system. Carefully refer to the wiring diagram and these instructions when wiring. Improper connections and inadequate grounding can cause serious injury or death. ● Before servicing, open and tag all disconnect switches. Never assume that electrical power is disconnected. Check with meter and equipment. ● Only use electrical protection equipment and tools suited for this installation. ● Use specified cables between Central Station EX and the power supply/air conditioner/external equipment. ● Shielded communication cable is not always required but strongly recommended to prevent communication issues for applications such as: Heavy and Light Industrial Buildings, Telecom Centers, Data Centers, Airports, Radio Stations, Hospitals/Healthcare buildings, and Offices. ● Use a dedicated power supply for the air conditioner at the unit’s rated voltage. ● Be sure to install circuit breakers (ground fault interrupter, isolating switch, molded case circuit breaker and so on), with the specified capacity. Ensure that the wiring terminals are tightened securely to recommended torque specifications. ● Clamp electrical wires securely with a cable clamp after all wiring is connected to the terminal block. In addition, run wires securely through the wiring access channel. ● When installing the power lines, do not apply tension to the cables. Secure the suspended cables at regular intervals, but not too tightly. ● Turn OFF and disconnect Central Station EX from the power source when wiring. Do not open the back cover without turning OFF the main power supply. ● Do not clean with, or pour water into, Central Station EX as it could cause electric shock and/or damage the product. Do not use strong detergent such as a solvent. Clean with a soft cloth.
  • Page 8: System Configuration

    2. System Configuration Connect Central Station EX to H-LINK (communication line) to control and monitor air conditioners. Use this software to control and monitor air conditioners remotely on personal computers (PCs) through Central Station EX. < Example > Power Line Pulse Transmission Meter (Field-Supplied) (Field-Supplied) Indoor Indoor Indoor Indoor Indoor Indoor Pulse Unit Unit Unit Unit Unit Unit Transmission Meter (Field-Supplied) Power Line Line Termination VPN Router External Device Internet Equipment (Field-Supplied) (Demand Controller, (Field-Supplied)
  • Page 9: About This Manual

    3. About This Manual This operation manual describes the setup procedure for Remote Access software. Refer to the operation manual for Central Station EX for how to operate the software. 4. Preparation Test Run ● Test runs of Central Station EX and Energy Calculation Software (if in use) need to be completed before installing Remote Access software. Complete installation of Central Station EX and Energy Calculation Software according to the installation and maintenance manuals for Central Station EX and Energy Calculation Software. ● PC is necessary to install Remote Access software. Prepare PC which meets the specification shown in the following section “4.2 PC Specification (Prepared on Site)”. 4.2 PC Specification (Prepared on Site) Item Specification ® ® Windows7 (32bit/64bit) Professional Windows10 (32bit/64bit) Pro ® Intel Core™ i3 2.0GHz or greater Memory 4GByte or more Resolution 1280 × 800 or more ® 16GByte for 32bit and 20GByte for 64bit as Windows minimum system requirements...
  • Page 10: Network Environment

    4.3 Network Environment Central Station EX is designed to be used in the LAN environment. 4.3.1 Connecting the remote PC with the dedicated LAN As the configuration example shown below, connect Central Station EX (and Central Station EX Adapter) and ® PCs for Remote Access software through Ethernet Hub. Configuration example of the dedicated LAN H-LINK Ethernet ® PSC-A128EX3 Air Conditioner Central Station EX PC 1 for Remote Access software H-LINK PSC-AD128EX3 Air Conditioner Central Staion EX Adapter PC 2 for Remote Access software 4.3.2 Connecting the remote PC with the existing LAN As the configuration example shown below, connect Central Station EX (and Central Station EX Adapter) and PCs for the Remote Access software to the existing LAN environment.
  • Page 11 (2) for Central Station EX Go to [Detail setting]-[Register network]-[H-LINK No.00] to set IP address, subnet mask, and default gateway. Example IP address: 192.168.0.50 Subnet mask: 255.255.255.0 Default gateway: 192.168.0.1 (for the LAN side of the VPN router) (3) for Remote PC (for Remote Access software) Go to [Control Panel]-[Network & Internet] to add VPN and set a fixed global IP address or fixed URL of the VPN router installed on site as destination. A dedicated VPN software might be needed depending on the VPN router. Refer to the manual for the VPN router for settings. ● Network Security (1) Take an adequate security measure for the network on your own responsibility so that unauthorized users cannot access the PC. (2) HITACHI does not take any responsibility for damage or loss caused by network security problem such as unauthorized access. Examples of security ▪ Use this software on a secure network with a properly configured firewall. ▪ Use this software on a physically independent network or on a virtual network using VLAN. ▪ Make sure that detection and removal of computer viruses and malicious programs are regularly performed on the PCs with this software installed. NOTES: ● Make sure that IP addresses of Central Station EX, Central Station EX Adapter, and PC for Remote Access software do not conflict with each other. ● When installing this system in the existing LAN wiring, ask your network administrator who manages the LAN how to set the network addresses (IP address, subnet mask, and default gateway). ● When using this system through internet, ask your network administrator who manages the LAN or the internet service provider you contract with how to configure VPN routers and set network addresses (IP address, subnet mask, and default gateway).
  • Page 12: Changing Ip Address Of Pc For Remote Access Software

    4.3.4 Changing IP address of PC for Remote Access software Change the IP address of the PC for Remote Access software as necessary. The initial IP address of Central Station EX is “192.168.0.50”. Make sure the IP addresses do not confl ict with each other in the same network. The setting steps diff er depending on the OS used. Follow the steps below accordingly. ® (1) Changing IP Address in Windows7 Click Start. Click Control Panel. Select Small Icons from View by. Continue to next page. A12124920A...
  • Page 13 Continue from previous page. 4. Click Network and Sharing Center. 5. Click Change Adapter Settings. 6. Right-click Ethernet, and then select Properties. Continue to next page. A12124920A...
  • Page 14 Continue from previous page. 7. Select Internet Protocol Version 4 (TCP/IPv4), and then click Properties. 8. Enter IP address, Subnet mask, and Default gateway, and then click OK. A12124920A...
  • Page 15 ® (2) Changing IP Address in Windows10 Click Start. Click Windows system. Click Control Panel. Select Small Icons from View by. Continue to next page. A12124920A...
  • Page 16 Continue from previous page. 5. Open Network and Sharing Center. 6. Click Change Adapter Settings. 7. Right-click Ethernet, and then select Properties. Continue to next page. A12124920A...
  • Page 17 Continue from previous page. 8. Select Internet Protocol Version 4 (TCP/IPv4), and then click Properties. 9. Enter IP address, Subnet mask, and Default gateway, and then click OK. A12124920A...
  • Page 18: Setup

    5. Setup 5.1 Installation 5.1.1 Installing Remote Access software Insert the SD memory card of Remote Access software into the SD memory card drive of the PC prepared for Remote Access software. Right-click “installer.exe”, and click “Run as administrator”. Click the [Next] button to install the software on the PC. Select the input box and enter the serial code. ● The serial code is “60292296”. Click the [Next] button. Continue to next page. A12124920A...
  • Page 19 Continue from previous page. 5. After confi rming the software license agreement, click “I agree to the software license agreement.” 6. Click the [Next] button. Note that you cannot click the [Next] button until you agree to the software license agreement. 7. Click the [Install] button. 8. Installation begins. The software will be installed on C drive. Note that you cannot change the installation destination. Continue to next page. A12124920A...
  • Page 20 Continue from previous page. 9. Click the [Finish] button and the installation will be complete. 10. Confi rm that the shortcut icon for Remote Access software has been created on the PC desktop. A12124920A...
  • Page 21: Starting Remote Access

    Starting Remote Access 5.2.1 Setting IP Address of Central Station EX Double-click the shortcut icon for Remote Access software. Tap Setting menu is shown. Tap Edit. Connection Setting window is shown. Continue to next page. A12124920A...
  • Page 22 Continue from previous page. 4. Select the input box and enter the connection setting name. Up to 16 characters can be entered. 5. Select the input box and enter the IP address of the Central Station EX. 6. Tap to confi rm and save the setting. ● Repeat step 2 to 6 to register more connection Settings. ● Up to 16 central controllers can be registered on 1 PC with Remote Access software installed. 1 PC can access only 1 central controller at a time. A12124920A...
  • Page 23: Starting Remote Access

    5.2.2 Starting Remote Access 1. Tap → . Remote Access software will start. ● Refer to the operation manual for Central Station EX for the operation after startup. Refer to the operation manual for Energy Calculation Software if in use. ● The time on Central Station EX and the PC with Remote Access installed, and the setting of daylight saving time should be the same when daylight saving time is active on the PC. ● When the time on Central Station EX and the PC with Remote Access installed are diff erent, set daylight saving time on the PC inactive. ● Do not select “2 hours” for shifting time when Remote Access is in use. A12124920A...
  • Page 24: Troubleshooting

    6. Troubleshooting Check the following table before contacting a distributor for maintenance. Item Phenomenon Check Action Remote Access software Did you install the software Reinstall the software according to the does not start when double- with administrator privileges? installation procedure in the operation clicking the shortcut for manual for Remote Access. Remote Access software on the PC desktop. Does the PC meet the Install the software on the PC which specifications? meets the specifications shown in the operation manual for Remote Access. Do you have enough free space Ensure enough free disk space on the hard disk? according to the specifications shown in the operation manual for Remote Access. ● T he Message “Could not Is the access address correct? Verify the address of the target Central connect to the controller. Station EX and set the correct access Check access address address.
  • Page 25: Cleaning

    7. Cleaning ● Wipe off the dirt using a soft, dry and clean cloth. If the screen surface of Central Station EX is very dirty, soak a soft cloth in water with a very small amount of neutral detergent, completely squeeze the cloth, gently wipe the dirt, and wipe off the moisture with a dry, soft cloth. ● Do not use benzene, paint thinner, or surfactant for cleaning. A12124920A...
  • Page 26 Software Licensing The software incorporated in this product is composed of multiple independent software modules. The copyright of Johnson Controls-Hitachi Air Conditioning (hereafter called “our company”) and a third party exist in each software module. The software modules our company has developed and created are included in this product. However, our company’s ownership and intellectual property rights are present in the software and the documentation attached. They are protected by copyright law and other laws. In addition, this product uses software modules which are licensed as free software. Customers can obtain the Source Code of the software modules, and in accordance with the License, they have the right to reproduce, modify and redistribute. For inquiries concerning the way of obtaining the described software modules, please contact us via the inquiry form below. https://www.jci-hitachi.com/products/contact/?ctgr=oss-license Concerning the software modules, in addition to our company, there are other holders who have copyright and other rights, and because this license is free of charge, there are provided as it is. Also, they are not guaranteed at all (it doesn’t matter what is specified and what is not) within the scope of the applicable laws and regulations. In addition, our company, which will not be responsible in any way within the scope of the applicable laws and regulations, will not bear the cost (including loss of data, loss of accuracy or incompatibility of interface with other programs) even when any damage are caused by customers who use or obtain this software modules. For more details concerning the conditions of use of these software modules, please contact us through the following URL of Johnson Controls-Hitachi Air Conditioning. https://www.jci-hitachi.com/products/contact/?ctgr=oss-license A12124920A...
  • Page 27 A12124920A...
  • Page 28 © 2019 Hitachi-Johnson Controls Air Conditioning, Inc. A12124920A, 2019...

Table of Contents