Table of Contents
Advertisement
Quick Links
Specs №
D-F10087
Product Specifications
2 inch Compact KIOSK Face Mount Printer
N P – K 2 0 9 2
st
Revision 1.00 2011.10.24 1
edition
All specifications described are subject to change without prior notice.
Please contact us for double-checking if you find any descriptions unclear
or something which seems to be mistyped or mistranslated.
Nippon Primex Inc.
Head Office:
1-5-12 Unoki Ohta-ku Tokyo 146-8650 Japan
TEL :+81-3-3750-5817 FAX :+81-3-3750-4555
E-mail : overseas@primex.co.jp
URL : http://www.primex.jp
D-F10087 NP-K2092 Product Specifications Rev.1.00
Advertisement
Table of Contents
Related Manuals for Nippon Primex NP-K2092
Summary of Contents for Nippon Primex NP-K2092
- Page 1 Please contact us for double-checking if you find any descriptions unclear or something which seems to be mistyped or mistranslated. Nippon Primex Inc. Head Office: 1-5-12 Unoki Ohta-ku Tokyo 146-8650 Japan TEL :+81-3-3750-5817 FAX :+81-3-3750-4555 E-mail : overseas@primex.co.jp URL : http://www.primex.jp D-F10087 NP-K2092 Product Specifications Rev.1.00...
- Page 2 Record of Revision Descriptions Rev. Approval Page Item Change 1.00 New release Kobayashi 2011.10.25 2011.10.24 D-F10087 NP-K2092 Product Specifications Rev.1.00...
- Page 3 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. D-F10087 NP-K2092 Product Specifications Rev.1.00...
- Page 4 • Absolutely do not open the printer unit while printing or cutter movement. It may damage thermal head or cutter. • Do not pull paper with close status of the printer unit. • Do not block the paper outlet while print movement. Also, do not grab the paper while print movement. D-F10087 NP-K2092 Product Specifications Rev.1.00...
- Page 5 • A part of this product is made from plated sheet steel. It does not affect the product’s quality and performance at all even if the cut face of the steel get rusty after a long time period. • This product may occur scrape etc, to the print surface because of its structure. D-F10087 NP-K2092 Product Specifications Rev.1.00...
- Page 6 • Do not conduct operation that is not suggested in this instruction. It may cause accident or failure. • Data can not be long-term stored, permanently stored and saved since it is basically evanescent. Nippon Primex Inc is not responsible for any damages of data deletion or lost income due to breakdown, repair or inspection.
-
Page 7: Table Of Contents
5.3 How to handle each cable ············································································································· 31 Separate reference document (Please refer to document below for command and code page) • Command reference [NP-K2092] (D-F10087) The following code pages are described besides command in the command reference. Domestic Character Code Table, Overseas Character Code Table, Code Page 858, International Character Code Table, Code Page 1250, Code Page 1251, Code Page 1252, Code Page 1254 •... -
Page 8: Overview
D : Dual Interface (SERIAL-RS232C and USB-V2.0 FULL SPEED) – select use Conceivable specifications for production U : USB (V2.0 FULL SPEED) only R : SERIAL (RS232C) only (5) Power Supply Voltage (Fixed) Standard M : DC12V (±5%) (6) OEM (Factory setting) No mark : Standard D-F10087 NP-K2092 Product Specifications Rev.1.00... -
Page 9: Features
(16) Easy paper load due to auto loading function. *NOTE1 : There are conditions to use with Max. 100mm/sec Please refer to “5.1 Selection of receipt print surface and paper roll position” *NOTE2 : Notation of [F/W] in the sentence hereafter indicates [Firmware] D-F10087 NP-K2092 Product Specifications Rev.1.00... -
Page 10: Configurations
1.3 Configurations 1) NP-K2092D-M (standard) Component parts of this product are as follows; Component parts NP-K2092D-M № Name Specifications Q’ty NP-K2092D-M USB, SERIAL common use ○ *There is no attached accessories. (Neither sample paper roll) D-F10087 NP-K2092 Product Specifications Rev.1.00... -
Page 11: Specifications
4:Line feed Amount 4.25mm (1/6 inch) (Default) *NOTE1 : Printing speed varies on conditions. There are conditions to use with Max. 100mm/sec Please refer to “5.1 Selection of receipt print surface and paper roll position” D-F10087 NP-K2092 Product Specifications Rev.1.00... - Page 12 Please refer to “5. Printer Installation” 1:Individual carton size Approx. 206(W) × 152 (D) × 146(H)mm Package 2:Individual carton weight Approx. 600g 3:Master carton size Approx. 479(W) × 432 (D) × 324(H)mm 4:Master carton weight Approx. 8.4kg (includes 12 pcs) D-F10087 NP-K2092 Product Specifications Rev.1.00...
-
Page 13: Paper Specifications
OFF and wait until the condensation disappears. – Select thermal paper which has a low level of Na+ ion, K+ ion, CI- ion. When using non-recommend type of paper, it should be well evaluated in reliability. D-F10087 NP-K2092 Product Specifications Rev.1.00... - Page 14 Near End at 3-4mm larger diameter than 22mm prefixed value. (1) If a smaller roll diameter than approx.28mm is newly loaded. (2) If power turned off and returned as remaining roll diameter is lower than approx. 28mm. D-F10087 NP-K2092 Product Specifications Rev.1.00...
-
Page 15: Print Area
(1) Name of Symbols Symbol Name The number of dots for printing Left Margin Area of Printing Right Margin Paper Width (2) Relations between Paper Width and Printing Area -1+0 A(dot) B(±1mm) C(±0.2mm) D(±1mm) NP-K2092 D-F10087 NP-K2092 Product Specifications Rev.1.00... -
Page 16: Specifications Of Cutter
*We recommend to use partial cut for this product. When full cut, depending on use environment, cut paper may stick because of static electricity etc., or may jam to ejection outlet etc., please use upon sufficient confirmation. D-F10087 NP-K2092 Product Specifications Rev.1.00... -
Page 17: Paper Sensor
Distance from printer head to sensor position Sensor position 2) Sensor Position A(±1mm) B(±0.5mm) NP-K2092 7.5mm 3.0mm * In order to prevent malfunction of the paper sensor, please do not pre-print to paper feed direction of sensor position ±5mm width. D-F10087 NP-K2092 Product Specifications Rev.1.00... -
Page 18: Power Specifications
25v, electrostatic capacity of 2200μF between power supply and GND. * Please set element for excessive current protection and appropriate fuse to the power line. *We recommend to use power supply complied with LPS standard. D-F10087 NP-K2092 Product Specifications Rev.1.00... -
Page 19: Reliability Specifications
: Optimization [NOTE] * In case of using paper other than recommended paper, since life time will differ depending on paper quality, width and thickness, confirm with paper in actual use at the user’s side. D-F10087 NP-K2092 Product Specifications Rev.1.00... -
Page 20: Environment Specifications
Humidity : 10 ~ 90%RH Except, no condensation. High temp and humidity: 40ºC90%RH (no condensation) shall be the worst value. 2.9 Regulations VCCI : Class A (Acquired) : Class A (Acquired) CE marking : Acquired D-F10087 NP-K2092 Product Specifications Rev.1.00... -
Page 21: External Dimension
This drawing shows status when attaching paper holder to the right looking from paper inlet side. (Paper load will be conducted from the left side.) In case of attaching paper holder to the opposite side, it will be symmetry position against to “Paper Sensor”. D-F10087 NP-K2092 Product Specifications Rev.1.00... -
Page 22: Configurations
: Receive buffer remaining amount's auto-reply format (when MS2-5: OFF) [FF]h + [01]h + [00]h + [00]h + [00]h + n *[00 ≤ n ≤ 0F]h n = Receive buffer remaining amount (0 ~ 15K Byte) D-F10087 NP-K2092 Product Specifications Rev.1.00... -
Page 23: Interface [Serial (Rs-232C Compliance)]
*NOTE3 Occur when power OFF or during self diagnostic print and software reset or when receiving buffer full or after receiving memory switch setting command and firmware rewrite. D-F10087 NP-K2092 Product Specifications Rev.1.00... -
Page 24: Connector Signal Details
Connect to “Standard paper near end sensor” [NOTE] • Please do not connect other than “Standard paper near end sensor” • Please valid memory switch MS2-4. CN1: Power Input Connector CN4: RS232C Connector CN2: Paper NE Connector CN3: USB Connector D-F10087 NP-K2092 Product Specifications Rev.1.00... -
Page 25: Functions
Please turn the power OFF/ON when switching to serial mode. SERIAL is not available in U-type. Table 2: SERIAL transmission speed SERIAL MS1-4 MS1-5 MS1-6 Factory Setting transmit speed 115200 57600 38400 19200 14400 9600 ○ 4800 2400 D-F10087 NP-K2092 Product Specifications Rev.1.00... - Page 26 (iii) Contents assigned in • • • • apply to all of the data including standard status, status header (0xFF). (iv) Printer ignores ESC s FEh command. (v) Do not issue ESC s FEh command from driver and tool. D-F10087 NP-K2092 Product Specifications Rev.1.00...
- Page 27 In case of setting MS2-6:ON, near end happens (detection signal ON) right after detecting with near end sensor. This value is rough indication. Since the detective value fluctuates depending on the condition of the paper, please treat as reference value. D-F10087 NP-K2092 Product Specifications Rev.1.00...
- Page 28 *Refer to “4.1.1 Switch Setting” for each MS content and [NOTE]. *Refer to [Memory Switch Setting and Printing]<GS M n d1 d2> for MS setting by command. *It is also possible to transmit MS setting command by using NiiPrinterTool etc. D-F10087 NP-K2092 Product Specifications Rev.1.00...
-
Page 29: Error Handling
• Please refer to “4.6 Operation Panel” for details about ALARM status. • After solving paper near end, it full cuts after auto loading the paper. • After solving platen open, it full cuts after feeding the paper. D-F10087 NP-K2092 Product Specifications Rev.1.00... -
Page 30: Buffer Full Print
Language Font Selecting Method Japanese Command [FS &], [FS .] or shift JIS code switch Polish Fixed (only half size) Russian Fixed (only half size) Scandinavian Fixed (only half size) Turkish Fixed (only half size) D-F10087 NP-K2092 Product Specifications Rev.1.00... -
Page 31: Operation Panel
It can not be pressed by finger in order to prevent mis-operation. (Push it lightly with ballpoint pen edge etc and release.) ALARM LED FEED switch RESET switch D-F10087 NP-K2092 Product Specifications Rev.1.00... -
Page 32: How To Set Paper Roll
– When inserting paper tip with fracture or bias status, it may not be able to conduct loading operation. – Since thermal head right after printing will be highly heated, please beware not to touch with your finger or hands etc. – Please beware not to clamp your finger or hands etc. D-F10087 NP-K2092 Product Specifications Rev.1.00... -
Page 33: How To Remove The Remained And Jammed Paper
– When opening the printer unit, please do not apply excess force by cross over stop position. – Please beware not to clamp your finger or hands etc. OPEN Open Lever Knob Printer Unit CLOSE D-F10087 NP-K2092 Product Specifications Rev.1.00... -
Page 34: Cleaning Method For Thermal Head And Others
– Please make sure to turn ON the power after ethanol or IPA is completely dried. Thermal Head Paper Sensor Open/Close Detection Switch Platen D-F10087 NP-K2092 Product Specifications Rev.1.00... -
Page 35: Frame Ground
Fix by screwing (recommend with toothed metal washer) frame ground of mounting side chassis and this product with using “Mounting Hole B, C, D and E” and connect frame ground with using electric wire of more than AWG#20 (recommended) at the shortest position. D-F10087 NP-K2092 Product Specifications Rev.1.00... -
Page 36: Printer Installation
MAX.90mm/sec that is default setting. When using “PD160R” or with other mounting positions, it can be used under MAX.100mm/sec. When using under MAX.100mm/sec, it requires to set by [Maximum Print Speed Setting] «GS S n» command. D-F10087 NP-K2092 Product Specifications Rev.1.00... -
Page 37: Position Change Of Paper Holder
• Screws (M4) are self-tapping type. When screwing to the new attachment hole, you may feel the rotating force of the screw driver heavy. • Although attaching positions of the paper holder are symmetric, there is no B-2 hole of left surface position. (2 holes in B-1, B-3) D-F10087 NP-K2092 Product Specifications Rev.1.00... -
Page 38: How To Handle Each Cable
Depending on paper holder attaching direction, paper roll position, handling of the cable changes. Please handle accordingly not to trouble when operating such as paper roll replacement etc. There is “Cable Hook Part” equipped to the figure position below. Please use when necessary. Interface cable Cable Hook Part D-F10087 NP-K2092 Product Specifications Rev.1.00...