2 inch compact kiosk face mount printer (38 pages)
Summary of Contents for Nippon Primex NP-2411
Page 1
FAX: +81 3 3750 4555 E-mail: overseas@primex.co.jp URL: http://www.primex.jp [Notice] *All features and specifications referred are subject to change without prior notices. *Please contact us if there is any wrong description or missing in this specification. D-F0472 NP-2411/3411 Product Specifications Ver.1.00...
Page 3
Plug off the printer when the product is not in use for a long time. DO NOT disassemble or modify the product. In case of disposal, follow the regulations or rules of the local authorities. Use power supply in conformity with LPS standard. D-F0472 NP-2411/3411 Product Specifications Ver.1.00...
Page 4
The coverage of warranty is limited within the product itself, Nippon Primex Inc is NOT responsible for anything induced by the defect of the product and DO NOT pay for any compensation that may occur.
4.7 How to set Roll Paper··········································································································27 4.8 How to remove the remaining paper, jammed paper. ··························································30 4.9 How to clean thermal head··································································································30 Commands ·····························································································································31 5.1 Command Table ··················································································································31 5.2 Printer Driver ·······················································································································33 5.3 Command Details ················································································································33 D-F0472 NP-2411/3411 Product Specifications Ver.1.00...
* Since the above chart is a standard specification, contact us for other specifications. * When using bezel, beware paper length not to be below 55mm. (If paper length is below 55mm, it will be difficult to take out paper from the bezel.) D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
II. Besides ID12mm of roll paper, it enables to use roll paper of ID25.4mm by attaching separately available attachment. III. Besides ex-factory setting of near end detection is OD22mm, it enables to change to 24mm dia. by adjusting sensor position. *NOTE1) Please see “2.2 Paper Specifications” for details. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
Specification Paper support For core ID25.4mm 35-00168 (1) Printer Main Body (NP-3411 or NP-2411) ………… 1 unit (2) Accessories * Thermal roll paper (sample) …………… 1 roll (3) Separately available accessory * Attachment for inner core diameter of 25.4mm ….2 pieces * Starting from April2008, it was changed from standard accessory to separately available accessory.
Since it detects roll paper O.D. by using reflection photo sensor, near end detection will not be available when using axis core excessing detecting value. *Printing surface shall be outer surface. Involute paper is not applicable. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
Page 13
(Recommended position for OD33.4mm) [CAUTION] *Remaining setting for axis inner core diameter of 25.4mm, unscrew the M2 screw and re-screw to another screw hole. (Loosen the screw and slide from “C” to “D” for adjustment.) D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
Page 14
In case of dew drop, turn OFF and wait until the dew disappears. *Select thermal paper which has a low level of Na+ ion, K+ ion and CI- ion when using non-recommended thermal paper and should be well evaluated in reliability. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
*NOTE1: It is possible to set by turning on memory switch MS2-7 (refer to 4.1.2 Memory switch MS2), however the right margin (D) will be 1mm, so that printing may be out of range due to paper bias. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
* Since there is automatic paper feed of approx. 2mm for a paper jam protection after paper cut, the above cutting margin will be 11.5±1mm. *When selecting “Full cut” in control no. do NOT use any other cut modes except full cut. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
Sensor 1 position (standard) Sensor 2 position (option) Paper width (2) Sensor Position A (±1mm) B (±0.5mm) C (±0.5mm) D (-1mm) 2 inch 11.5 3 inch 72.5 *Take off or wipe out and clean the sensor periodically. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
Page 18
Preprint with dark color is prohibited in mark width area. Confirm with extra care when using preprinted paper. *NOTE1: It is not applicable when selecting “sensor 2” with paper width of 76mm. Please contact us for any supports. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
Should it is not conductable, connect cables near by the printer and place an electrolysis condenser of approx. 2200u between PS and GND. Voltage resistance should be higher than 35V. * Use power supply complied with LPS. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
Recommended thermal papers Print Density: 100% * Life duration will differ when using the non-recommended papers because of its quality, width and thickness. Have the user confirm itself with paper that user intends to use actually. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
: Acquired NOTE UL60950-1 : Acquired * 1 VCCI : Class A (Acquired) : Class A (Acquired) : Acquired *NOTE1: It will be unapplied when selecting different appearance as standard at the control no. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
«Reference diagram» t=1.0 t=1.0 Insert printer from arrow Side view 側面視 direction and hook metal plate of mechanism side fixation screw part. From mechanism side printer fixation hole プリンタ取付穴(メカ側)中心より D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
Page 23
«Reference diagram» t=1.0 t=1.0 Insert printer from arrow Side view 側面視 direction and hook metal plate of mechanism side fixation screw part. From mechanism side printer fixation hole プリンタ取付穴(メカ側)中心より D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
(7) Received control (RTS signal) Mark : Impossible to receive data Space : Possible to receive data (8) Transmit permission (CTS signal) Mark : Impossible to forward data Space : Possible to forward data D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
Pin No. Signal Input/Output Function Remark Input Serial received data Output Serial transmitted data Output Receivable signal Connect to No.7 Signal ground Output Receivable signal Connect to No.4 Input Transmit permission signal 1, 6, 9 N.C. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
Page 26
* This connector equips with standard paper-holder PH-10. Enable to visual check from the outside. CN 3 CN 2 1) CN 3 CN 2 2) CN 4 U type D type Power Supply Jack: 2 pin type Power Supply Jack: Round shape type (standard) D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
MS1-1 MS1-2 MS1-3 NONE 8 bit EVEN Serial NONE 7 bit EVEN Reserve Table 2 : SERIAL baud rate setting SERIAL baud rate setting DS1-4 DS1-5 115200 bps 38400 bps 19200 bps 9600 bps D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
Page 28
Print area 69(54)mm 72(52)mm MS2-8 Print density Dark Standard *Setting of MS2-5 and MS2-6 must be “OFF” at normal operation. *2: Figures in ( ) will be applied for NP-2411 Table 3: Built-in language font Japanese Korean Chinese Greek MS2-2 MS2-3...
Page 29
Since it is not detectable, do NOT use a roll paper that is glued to the core at the end of the paper. Replace to a new paper as soon as detection of paper out. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
Buffer full data varies on the size of ANK or Kanji respectively. (please refer to “2.1 2 printing specification”) D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
No switch (only half size, no full size) Scandinavian No switch (only half size, no full size) Turkish No switch (only half size, no full size) *NOTE1: Since 00h ~ 1Fh are control code, those will not print. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
Since printer will return to same status as turning the switch on when activating RESET switch, it requires setting it again. It requires precaution when data remains to buffer because data will be deleted. FEED SWITCH ALARM LED RESET SWITCH D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
(Beware not to apply excess force when widening the paper holder.) 2) Fit and insert paper core hole to circular boss. (Make sure the holder is set in parallel.) (Make sure circular boss fits appropriately into the paper core hole.) Roll Paper Circular boss D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
Page 34
(Make sure not to apply excess angle when opening the head cover. Also, beware not to catch a finger or hand in the cover.) *Since thermal head may be highly-heated right after printing, beware not to touch it. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
Page 35
Also, beware not to catch a finger or hand in the cover. *Since thermal head may be highly-heated right after printing, beware not to touch it. When closing thermal head cover, make sure to close by pressing metal plate part not the head open lever. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
*It may have a bloom of paper depending on papers, check at the period of maintenance and decide what kind of a paper to use. *Make sure to turn ON the power after its complete dry. *Make sure not to apply excess angle when opening the head cover. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
[Memory Switch Setting and Printing] « GS M n d1 d2 »··························· 49 [Fixed Bit Image Print] « GS P n »·············································· 50 [Fixed Bit Image Registration] « GS T n » ······································· 50 D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
Page 38
[Quadruple Japanese Kanji Size SET/RESET] « FS W n » ························ 56 ▲ is affected on Japanese / Korean font selected from language font. ■ is affected on Japanese font selected. *In case of print method is buffer, max. printing speed will be 150mm/sec. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
* [00 ≤ n ≤ 20]h Sets right SPACE quantity of character by dot. (1/203 inch unit) * Right SPACE is reflected with zoom when double width zoom mode. * Default of “n” is [00]h. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
* [00 ≤ n ≤ FF]h SET/RESET download characters * Only least significant bit (b0) is effective to “n”. “b0” has the following meaning. Function RESET download character set SET download character set * Default of “n” is [00]h D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
203 dpi 101 dpi 21, 23 24dot double density 203 dpi 203 dpi <Relationship between Bit Image data and Printed Dot> * 8dots bit image D1 D2 D3 Print Data =1dot Single density Double density D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
Page 44
*24dots image bit D1 D2 D3 D4 D5 D6 D7 D8 D9 Print Data =1dot Single density Double density D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
Clears data stored in the print line buffer and initializes (default status) each setting. * Does not clear data stored in the internal receive buffer. * Does not re-read memory switch. * Stores in receive buffer and executes sequentially. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
SET enhanced print * Bold print and double strike print result in the same with this printer. * When executing enhanced print, print result may be deformed. * Default value of “n” is [00]h. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
*[00 ≤ n ≤ 0A]h Selects International Characters. * “n” has the following meaning. n(hex) Character Set U.S.A. France Germany U.K. Denmark I Sweden Italy Spain Japan Norway Denmark II *Default value of “n” is [08]h. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
(Except for definite bit image) * “n” has the following meaning; n(hex) Position Left alignment Centering Right alignment * Effective only when input in beginning of the line. * Default value of “n” is [00]h D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
* Setting amount does not remain. * Beginning of the line shall be the next print start position. * If there is print data remained, it definitely performs line feed at least for the same height of the character. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
* This command is effective only for SERIAL Interface. * Command should be issued before transmit of print data. (Stored into internal receipt input buffer and executes sequentially.) * Receivable except when internal receipt input buffer is full. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
* Once bit image download is defined with this command, it is effective until redefining, executing [Printer Initialization] or [Software Reset] or turning OFF the power. * Following diagram indicates relations between bit image data and defined dots. n1x8dots dn2+1 dn2x2+1 dn2+2 dn2x2+2 n2x8dots dn1xn2x8 dn2x2 D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
* Setting reverse print has priority over underline setting. Thus, even when underline is set, underline will not be added to black/white reverse character. However, underline setting remains effective. * When black/white reverse print, print result may be crushed. * Default value of “n” is [00]h. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
* “n” has the following meaning. n(hex) Printing position No printing Above barcode Under barcode Above & Under barcode *HRI character will be printed by font selected in [HRI Character Font Selection]. *Default value of “n” is [00]h. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
Code: [1D]h + [64]h + Dn * Downloads printer firmware in hexadecimal code and rewrites firmware according to the outcome, and reboots. * “Dn” is HEX code of firmware and complies with INTELLEX HEX format. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
HRI Characters, it prints HRI Characters for length of a line. * [00]h at the end of this command can be changed to [FF]h in [Barcode End Change]. * Refer to [Barcode Specifications Details] of appendix for details of barcodes. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
* Different sizes of characters mixed such as normal size, double height, double width and quadruple can be printed. * Combined print with ANK Character is also available. * Default value of “n” is [00]h. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
Code: [1C]h + [2E]h RESET Japanese Kanji mode. * It will be ineffective, when Japanese is selected with Shift JIS in Japanese Kanji Code system. * Default status is release of Japanese Kanji mode. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
* Once defined by this command, it will be effective until execution of [Software Reset] and RESET switch or turning OFF the power. * Only designated area will be redefined. <Example> 24dots P1 P4 P7 24dots P2 P5 P3 P6 D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
*[00 ≤ n ≤ FF]h SET/RESET Quadruple Japanese Kanji Character. * Only LSB (least significant bit “b0”) is available to “n”. “b0” has the following meaning. Function RESET Quadruple SET Quadruple * Default value of “n” is [00]h. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
Page 63
* Printer operation cannot be guaranteed if the blank control code (codes below [1F]h) is transmitted to printer. * This code table indicates simplified symbol and is not print result. There may be some difference from the actual print. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
Page 64
* Printer operation cannot be guaranteed if the blank control code (codes below [1F]h) is transmitted to printer. * This code table indicates simplified symbol and is not print result. There may be some difference from the actual print. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
Page 65
0Ah Denmark II # $ * This code table indicates simplified symbol and is not print result. There may be some difference from the actual print. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
Page 66
6.5 CODE PAGE 1250 * This code table indicates simplified symbol and is not print result. There may be some difference from the actual print. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
Page 67
6.6 CODE PAGE 1251 * This code table indicates simplified symbol and is not print result. There may be some difference from the actual print. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
Page 68
6.7 CODE PAGE 1252 * This code table indicates simplified symbol and is not print result. There may be some difference from the actual print. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
Page 69
6.8 CODE PAGE 1253 * This code table indicates simplified symbol and is not print result. There may be some difference from the actual print. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
Page 70
6.9 CODE PAGE 1254 * This code table indicates simplified symbol and is not print result. There may be some difference from the actual print. D-F0472 NP-2411/3411 Product Specifications Ver. 1.00...
Page 71
* Make sure to input “Start/Stop Code” Marks ($%*+-./:space) * Although can be printed out without “Start/Stop CODABAR Flexible Code”, it unables to read-out by scanner etc. Start/Stop Code(ABCD) (NW-7) length (abcd) * Refer to next page for “CODE128” D-F0472 NP-2411/3411 Product Specifications Ver.1.00...