Table of Contents
Advertisement
Quick Links
«24V KIOSK Printer with simple presenter»
*Since this product is under development, specifications etc. described in this manual may change.
All specifications described are subject to change without prior notice.
Please contact us for double-checking if you find any descriptions unclear
or something which seems to be mistyped or mistranslated.
D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00
Product Specifications
N P – K 3 0 5 3
N P – K 2 0 5 3
Revision 1.00 2011.03.09 1
Nippon Primex Inc.
Head Office:
1-5-12 Unoki Ohta-ku Tokyo 146-8650 Japan
TEL :+81-3-3750-5817 FAX :+81-3-3750-4555
E-mail : overseas@primex.co.jp
URL : http://www.primex.jp
Specs №
st
edition
D-F10072
Advertisement
Table of Contents
Related Manuals for Nippon Primex NP-K3053
Summary of Contents for Nippon Primex NP-K3053
- Page 1 Please contact us for double-checking if you find any descriptions unclear or something which seems to be mistyped or mistranslated. Nippon Primex Inc. Head Office: 1-5-12 Unoki Ohta-ku Tokyo 146-8650 Japan TEL :+81-3-3750-5817 FAX :+81-3-3750-4555 E-mail : overseas@primex.co.jp URL : http://www.primex.jp D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00...
- Page 2 Record of Revision Descriptions Rev. Approval page Item Content 1.00 New release Asahina 2011.03.10 2011.03.09 D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00...
- Page 3 • DO NOT block the paper outlet while print movement. Also, DO NOT grab the paper while print movement. • Although paper may slightly pass obliquely, there will be no problems in clamp and clamp release movement. D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00...
- Page 4 • A part of this product is made from coated steel plate. It does not affect the product’s quality and performance at all even if the cut face of the steel plate get rusty after a long time period. D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00...
- Page 5 • The coverage of warranty is limited within the product itself, Nippon Primex Inc is NOT responsible for anything induced by the defect of the product and DO NOT pay for any compensation that may occur.
-
Page 6: Table Of Contents
4.11 Frame Ground ····························································································································· 31 Separate reference document (Please refer to document below for command and code page) • Command reference [NP-K3053/NP-K2053] (D-F10072) * The following code pages are described besides command in the command reference. Domestic Character Code Table, Overseas Character Code Table, Code Page 858,... -
Page 7: Overview
2 : 2 inch (58mm) (2) Interface (Factory setting) Standard D : Dual Interface (SERIAL-RS232C and USB-V2.0 FULL SPEED) – select use Conceivable specifications for production U : USB (V2.0 FULL SPEED) (3) OEM (Complies with separate specifications manual.) D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00... -
Page 8: Features
Flash Memory and 3 patterns of registration available with NV bit image. *NOTE2 11) Option parts are separately available. *NOTE1 : Notation of [F/W] in the sentence hereafter indicates [Firmware] *NOTE2 : Please refer to “1.4 Option Parts” D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00... -
Page 9: Configurations
Since there are condition and restriction etc to use the option part, please consider upon reading each product specifications. 1) Power Supply PS8-*2 Power supply adapter is available. Please consider upon reading product specification D-F10058. D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00... -
Page 10: Specifications
Code Page 1254 (Half size) 3:Character Double width Modifications Double Height Quadruple Bold print Double strike Inverted 90°clock-wise rotation Underlined 4:Line feed Q’ty (Default) 4.25mm (1/6 inch) *NOTE1 : Print speed fluctuates depending on the condition. D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00... - Page 11 (includes 12 pcs) *NOTE2 : Since it will be hard to remove the paper roll, please beware paper length not to be below 60mm. *NOTE3 : Please make sure to use this printer installed horizontally. D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00...
-
Page 12: Paper Specifications
In case of dew drop, turn OFF and wait until the condensation disappears. – Select thermal paper which has a low level of Na+ ion, K+ ion, CI- ion. When using non-recommend type of paper, it should be well evaluated in reliability. D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00... - Page 13 Near End at 3-4mm larger diameter than 22mm prefixed value. (1) If a smaller roll diameter than approx.26mm is newly loaded. (2) If power turned off and returned as remaining roll diameter is lower than approx.26mm.. D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00...
-
Page 14: Print Area
1) Name of Symbols Symbol Name The number of dots for printing Left Margin Print Area Right Margin Paper Width 2) Relations between Paper Width and Print Area Model A(dot) B(±1mm) C(±0.2mm) D(±1mm) NP-K3053 NP-K2053 D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00... -
Page 15: Cutter Specifications
Since there is automatic paper feed of approx. 2mm for paper jam protection after paper cut, the above cutting margin of “B” will be 9.5±1mm. – Please do not operate such as narrow strip occur by cut. It will cause paper jam. D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00... -
Page 16: Paper Sensor
2.5 Paper Sensor Print Head Position Print Surface Feed Direction Sensor 1) Name of Symbols Symbol Description Distance from printer head to sensor position Sensor position 2) Sensor Position A(±1mm) B(±0.5mm) NP-K3053 NP-K2053 D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00... -
Page 17: Power Specifications
2200μ. Rating voltage is more than 32V. – Make sure to set element for excessive current protection and appropriate fuse to the power line. – Make sure to use power supply complied with LPS standard. D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00... -
Page 18: Reliability Specifications
Environmental temperature/humidity : 20ºC, 60% *In case of using paper other than recommended paper, since life time will differ depending on paper quality, width and thickness, confirm with paper in actual use at the user’s side. D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00... -
Page 19: Environment Specifications
High temp and humidity: 40ºC90%RH (no condensation) shall be the worst value. 2.9 Regulations CE marking (Uncertified: plan to acquire) VCCI : Class A (Uncertified: plan to acquire) : Class A (Uncertified: plan to acquire) D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00... - Page 20 2.10 Extrenal Drawing 1) NP – K3053 Rear View D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00...
- Page 21 2) NP – K2053 Rear View D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00...
-
Page 22: Configurations
: Receive buffer remaining amount's auto-reply format (when MS2-5: OFF) [FF]h + [01]h + [00]h + [00]h + [00]h + n *[00 ≤ n ≤ 0F]h n = Receive buffer remaining amount (0 ~ 15K byte) D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00... -
Page 23: Interface [Serial (Rs-232C Compliance)]
*NOTE3 Occur when power OFF or during self diagnostic print and software reset or when receiving buffer full or after receiving memory switch setting command and firmware rewrite. D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00... -
Page 24: Connector Signal Details
FG terminal attached in below figure of the printer. *In case of actual use, use after sufficient confirmation by the user’s side. FG terminal CN2 SERIAL connector CN3 USB connector CN1 Power Input connector D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00... -
Page 25: Functions
Please turn the power OFF/ON when switching to serial mode. SERIAL is not available in U-type. Table 2: SERIAL transmission speed SERIAL MS1-4 MS1-5 MS1-6 Factory Setting transmit speed 115200 57600 38400 19200 14400 9600 ○ 4800 2400 D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00... - Page 26 (iii) Contents assigned in • • • • apply to all of the data including standard status, status header (0xFF). (iv) Printer ignores ESC s FEh command. (v) Do not issue ESC s FEh command from driver and tool. D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00...
- Page 27 This value is rough indication. Since the detective value fluctuates depending on the condition of the paper, please treat as reference value. D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00...
- Page 28 *Refer to “4.1.1 Memory Switch” for each MS content and [CAUTION]. *Refer to “5.3 **) [Memory Switch Setting and Printing]” for MS setting by command. *It is also possible to transmit MS setting command by using NiiPrinterTool etc. D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00...
- Page 29 Please do not use a roll paper that is glued (or taped) to the core at the end of paper because that kind of a roll paper is impossible for the sensor to detect paper end status. Please replace a paper roll as soon as paper-out status is detected. D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00...
-
Page 30: Error Handling
Remove factor of error status occurring and will recover by restarting the power ON or pressing the reset switch. If conducting recovery/release operation, it requires to set again because the printer will be initialized. Please beware when data remains in buffer because it will be deleted. D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00... -
Page 31: Buffer Full Print
Language Font Selecting Method Japanese Command [FS &], [FS .] or shift JIS code switch Polish Fixed (only half size) Russian Fixed (only half size) Scandinavian Fixed (only half size) Turkish Fixed (only half size) D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00... -
Page 32: Operation Panel
Used also in self-diagnostic test, memory switch setting. 3) RESET Switch Printer returns to status when turning ON the power by activating RESET switch. (Push it lightly with ballpoint pen edge etc and release.) FEED switch ALARM LED RESET switch D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00... -
Page 33: How To Set Paper Roll
– Since thermal head right after printing will be highly heated, please beware not to touch with your finger or hands etc. – Please beware not to clamp your finger or hands etc. Paper Edge Shape Drawing D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00... -
Page 34: How To Remove The Remained And Jammed Paper
– Please press center part of platen arm when closing in order to prevent uneven clamping. – Make sure not to apply excess angle when opening the head arm. – Please beware not to clamp your finger or hands etc. Bezel Unit Platen Open Lever D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00... -
Page 35: Cleaning Method
– Please make sure to turn ON the power after its complete dry. – Please do not apply excess angle when opening the bezel unit. Platen Bezel Unit Presenter Sensor Platen Sensor Paper Sensor Thermal Head D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00... -
Page 36: Precautions Upon Installation
While printing, paper will temporarily placed by loop status as below figure and will be ejected after paper cut. Please secure “paper storage space” depending on length of printing receipt. Paper Storage Space Looped Paper Paper Ejection Slit D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00... -
Page 37: Frame Ground
Fix by screwing (recommend with toothed metal washer) frame ground of mounting side chassis and this product with using “Mounting Hole B or C” and connect frame ground with using electric wire of more than AWG#20 (recommended) at the shortest position. D-F10072 NP-K3053/K2053 Product Specifications Rev.1.00...