Table of Contents
Advertisement
OSCILLOSCOPE ACCESSORIES
Test Cable Banana-BNC
HZ32
Coaxial test cable; length 1.15m, characteristic impedance 50fl.
Cable capacitance 120pF. Input voltage max. 500Vp.
Test Cable BNC - BNC
HZ34
Coaxial test cable; length 1 m, characteristic impedance 50J1.
Cable capacitance 126pF. Input voltage max. 500Vp.
Adapter Banana-BNC
HZ20
Two 4mm binding posts (19mm between centers) to standard BNC
male plug. Input voltage max. 500Vp.
son Through-Termination
HZ22
For terminating systems with 50 Q characteristic impedance.
Modular Probes
Maximum load 2W. Max. voltage lOVp^s-
The clear advantage over ordinary probes are field replaceable
parts and the HF-compensation feature on the 10:1 attenuator pro¬
bes. For the first time, probes in this price range allow adjustments
of their FIF-characteristics to match individually the input imped¬
ance of each scope. This is particularly important for scopes with
higher bandwidths (>50MFIz), as otherwise strong overshoot or
rounding may occur, when measuring fast-rising square waves.
An exact FIF-compensation, however, is only possible with square-
wave generators having a risetime <5ns. Most FIAMEG scopes
already feature such a calibration generator. For other oscillo¬
scopes, it is available as accessory item FIZ60-2. At present the
following Modular Probes are available (FIZ36 without HF-com-
pensation);
Type
HZ36
selectable
Attenuation Ratio
1:1/10:1
Bandwidth min. (MFIz)
10/100
Risetime (ns)
35/3.5
Inp, Capacitance (pF)
47/18
Inp. Resistance (Mil)
1/10
Inp. Voltage max. (Vp)
600
Cable Length (m)
1.5
Spare Cable for HZ36
Spare Cable for HZ51. HZ54
Sparepart Kit (2 sprung hooks. 2
HZ51
HZ52
HZ53
HZ54
selectable
10:1
10:1 (HF)
100:1
1:1/10:1
150
250
150
10/150
<2
<1.4
<2
35/<2
16
16
6,5
40/18
10
10
100
1/10
600
600
1200
600
1.2
1.5
1,5
1.2
HZ 39
HZ57
tips, 1 ground cable)
HZ40
Demodulator Probe
HZ55
Special probe for AM-demodulation and wobbulator measure¬
ments. HF-Bandwidth lOOkFIz - 500MFIz (±1dB). AC Input Volt¬
age 250mV - 50Vrms- DC Isolation Voltage 200V DC including
peak AC. Cable length 1.2m.
High Voltage Probe
HZ58
For measurement of voltages up to 15kVpp. Input resistance
approx. 500mQ. Recommended load resistance) MQ/10MQ
(switchable). Attenuation ratio 1000:1. Bandwidth 1 MFIz. Cable
length 1.5 m. BNC connector.
Carrying Cases
For HM103
HZ95
For HM 203, HM204, HM205, HM208, HM408, HM604,
HM605 and HM 1005
HZ96
Viewing Hood
HZ47
ForHM203, HM204, HM205, HM208, HM408, HM604, HM605
and HM 1005
Scope-Tester
HZ
6
O
-2
For Checking the Y amplifier, timebase, and compensation of all
probes, the HZ 60-2 is a crystal-controlled, fast rising (typ. 3 ns)
square-wave generator with switchable frequencies of DC, 1-10-
100Hz, 1-IO-IOOkHz, and 1 MHz. Three BNC outputs provide sig¬
nals of 25 mVpp into 50 Q, 0.25 Vpp and 2.5 Vpp (open circuit for 10x and
lOOx probes); accuracy ±1%. Battery-powered.
Component-Tester
HZ65
Indispensable for trouble-shooting in electronic circuits. Single
component and in-circuit tests are both possible. The HZ65 oper¬
ates with all scopes, which can be switched to X-Y operation (ext.
horizontal deflection). Non-destructive tests can be carried out on
almost all semiconductors, resistors, capacitors, and coils. Two
sockets provide for quick testing of the 3 junction areas in any small
power transistor. Other components are connected by using 2
banana jacks. Test leads supplied.
Examples of Test Displays:
Short circuit
CapacitorSS^F
Junction E-C
Z-Diode<8V
Printed in West Germany 5/90
zi
Advertisement
Table of Contents
