Pioneer MJ-L7 Service Manual page 39

(2) Spin Setting
Setting Method
Remarks
MJ-L7
Display
Test mode STOP state [ tSmMM AACS & |
Press the MENU button four times
Reads each setting from the EEPROM.
EEPROM menu display mode
[ EEPROM SET ]
Press the PLAY/PAUSE button Focus setting menu [ Focus ]
Press the MENU button
Spin setting menu [ Spindle ]
Press the PLAY/PAUSE button
Spin system loop filter gain constant setting
(Until servo turns ON)
[SPG +¢]
Press the MENU button
Spin system loop filter gain constant setting
(After servo turns ON, inner circumference)
[SPG in ¢¢]
Press the MENU button
Spin system loop filter gain constant setting
(After servo turns ON, center)
[SPG mid ¢ ¢]
Press the MENU button
Spin system loop filter gain constant setting
(After servo turns ON, outer circumference)
[ SPG out ¢ ¢]
Press the MENU button Spin system loop filter f characteristics setting 1 [SP1 +¢]
Press the MENU button
Spin system loop filter f characteristics setting 2
[SP2 09]
Press the MENU button
Spin system loop filter f characteristics setting 3
[SP3 44]
Press the MENU button
Spin system loop filter f characteristics setting 4 [SP4 ¢¢]
¢¢: Setting
When the CANCEL button of DISPLAY unit is pressed at a step, the unit will shift to the opposite step.
When the + button of DISPLAY unit is pressed when the setting is displayed, the setting will increase and the new setting will be stored
in the RAM.
Press the MENU button Spin system loop filter f characteristics setting 5 [SP5 6]
@ When the — button of DISPLAY unit is pressed when the setting is displayed, the setting will decrease and the new setting will be stored
in the RAM.
When the STOP button of the Unit is pressed when the EEPROM setting menu is displayed, the test mode STOP state will be set.
When the STOP button of the Unit is pressed in the spin setting menu state, the EEPROM setting menu state will be set.
When the STOP button of the Unit is pressed at each setting item display state, the spin setting menu state will be set.
(3) Tracking Setting
Step No. Setting Method
Remarks
Display
Step 1
Test mode STOP state
[ tom A Ace |
Step 2
Press the MENU button four times
Reads each setting from the EEPROM.
EEPROM menu display mode
[ EEPROM SET ]
Step 3 Press the PLAY/PAUSE button
Focus setting menu [ Focus ]
Step 4
Press the MENU button two times
Tracking setting menu
[ Tracking ]
Step 5
Press the PLAY/PAUSE button Tracking system loop filter gain constant setting [TG o¢]
Step 6
Press the MENU button
Tracking system loop filter f characteristics setting 1 [TF1 ¢¢]
Step 7
Press the MENU button
Tracking system loop filter f characteristics setting 2 [TF2 ¢¢]
Step 8 Press the MENU button Tracking deceleration pulse level setting (For one jump)
[ TRBLVo ¢¢]
Step 9 Press the MENU button
Tracking deceleration pulse level setting (For ten jumps)
[ TRBLVt + 4]
Step 10
Press the MENU button
Tracking pulse level setting (For one jump)
[ TRKLVo #4]
Step 11
Press the MENU button
Tracking pulse level setting (For ten jumps)
[ TRKLVt ¢ 4]
Step 12
Press the MENU button
Tracking drive pulse width setting (For one jump) [TDPWo ¢¢]
Step 13
Press the MENU button
Tracking drive pulse width setting (For ten jumps) [TDPWt ¢¢]
Step 14 Press the MENU button
Tracking slide stop time setting (For one jump)
[ SLCTo ¢¢]
Step 15 Press the MENU button
Tracking slide stop time setting (For ten jumps)
[SLCTt +6]
Step 16
Press the MENU button
Tracking slide stop time setting (During moving) [SLCTm ¢¢]
39