Related Manuals for Caple INCHW3
Summary of Contents for Caple INCHW3
- Page 1 INCHW3 Integrated Cooker Hoods INSTRUCTIONS Caple Quality Products Consumer Help Line 0870 2411142 Page INCH.DOC...
-
Page 2: Table Of Contents
Requesting Service The author and publisher have used their best efforts in preparing this book. The Caple Group and the author make no representation or warranties with respect to the accuracy or completeness of the contents of this book. The information in this book is subject to change without notice. -
Page 3: Installer
SAFETY WARNINGS These warnings are provided in the boiler then its flue must be of the interests of safety. Ensure you read room sealed or balanced flue type. understand them before installing or using this appliance. • If other types of flue or appliance are fitted ensure that there is an adequate INSTALLER supply of air to the room. -
Page 4: Electrical Connections
Any permanent electrical installation must Depth 270-360mm comply with the latest I.E.E. Regulations and local Electricity Company regulations. INCHB3 - INCHW3 For your own safety this should be Ducting Spigot 100mm dia. undertaken by a qualified electrician e.g. Weight - Gross 11.90kg... -
Page 5: Installation Requirements
INSTALLATION INSTRUCTIONS INSTALLATION REQUIREMENTS Please ensure that when the appliance is 1 No. Wall fixing template. 1 No. Decor installed it is easily accessible to an panel fixing template. 1 No. Instruction engineer in the event of a breakdown. booklet. 2 No. Wall brackets. 4 No. 44mm Wall bracket fixing screws. -
Page 6: Wall Fitting
INSTALLATION INSTRUCTIONS WALL FITTING The hood should be secured on each side to the adjoining wall cabinets using the To fit the cooker hood to the wall, use the four 13mm round headed screws paper template provided to mark the hole provided. -
Page 7: Adjusting The Visor Mechanism
INSTALLATION INSTRUCTIONS Push the visor in, until an audible click is FITTING THE DECOR PANEL heard. The visor can now be opened and To fit the decor panel, it is necessary to closed in it’s normal function. remove the visor from the cooker hood. ADJUSTING THE VISOR MECANISUM The decor panel should be fitted in The tension on the visor guides can be... -
Page 8: Extraction (Ducting)
The length of ducting should be no more than: 3 metres with one 90° bend The INCHB3, INCHW3 & INCHP3 2 metres with two 90° bends hood require one CAP10CF charcoal filter. The twin motor DL/INCHP3 hood requires two CAP10CF charcoal Bends of more than 90°... -
Page 9: Controls
OPERATING INSTRUCTIONS CONTROLS Position-3 Should selected when frying or cooking food with a Two slider switches and an automatic strong odor. micro switch control the cooker hood functions, which are located on the right hand side behind the visor. To obtain the best performance it is ELECTRICAL CONNECTION advisable to switch 'ON' the hood a few minutes before you start cooking and... -
Page 10: Cleaning
A build up of grease and fat INCHB3 INCHW3 hood from cooking could be a fire hazard. require one CAP7CF charcoal filter. Never use excessive amounts of water... - Page 11 months or more frequently if the hood is used for more than three hours a day. To remove the grille panel press inwardly on the two catches located at each side of the grille panel and the panel will slide down.
-
Page 12: Metal Grease Filter
CLEANING AND MAINTENANCE Pull the bottom edge the grille panel forward to disengage the runners. Lay the grille assembly face down and carefully ease out the wire retaining clips. Clean the grille and clips before fitting the replacement paper grease filter and refit the wire clips. -
Page 13: Before Calling A Service Engineer
In the event of your cooker hood requiring before calling a Service Engineer. It may service telephone Caple Service on: be that the problem is a simple one, which 0870 241 1142. solve...