Page 2
SERVICE MANUAL E27BSR COMPACT CRAWLER EXCAVATOR TIER 4 Service Manual Number S5PV0020E01 EN-US Issued 09-2008 Find manuals at https://best-manuals.com...
Page 3
CNH America LLC reserves the right to make improvements in design or changes in specifications at any time without incurring any obligation to install them on units previously sold. All data given in this publication is subject to production variations. Dimensions and weights are only approximate. Illustrations do not necessarily show products in standard condition.
Page 4
E27BSR SERVICE MANUAL TABLE OF CONTENTS SECTION 1 SAFETY AND GENERAL INFORMATION Section Table of Contents ................I Book/Form Number: 5-16540 EN-US CHAPTER 1 GENERAL PRECAUTIONS FOR MAKING REPAIRS...
Page 5
E27BSR CHAPTER 3 TRAVEL SYSTEM Table of Contents ............... . 3-1 Book/Form Number: 5-16690 EN-US SECTION 5 TROUBLESHOOTING...
Page 6
SAFETY GENERAL SAFETY INFORMATION CAUTION- Indicates a potentially hazardous WARNING situation which, if not avoided, may result in minor or moderate injury. It may also be used to Do not operate or perform any maintenance on this alert against possible damage to the machine machine until instructions...
Page 7
SAFETY PRECAUTIONS WARNING WARNING Do not operate this machine unless you have read and understand the instructions in the OPERATOR’S The proper and safe lubrication and maintenance for MANUAL. Improper machine operation is dangerous this machine, recommended by Manufacturer, are and could result in injury or death.
Page 8
SAFETY 13. Always use the proper tools that are in good 21. Do not operate a machine if any rotating part is condition and that are suited for the job at hand. damaged or contacts any other par t during Be sure you understand how to use them before operation.
Page 9
NOTE: This Manual may be properly revised due to the i m p r o v e m e n t o f p r o d u c t s , m o d i f i c a t i o n o f This Manual is prepared as a technical material in specifications, etc.
Page 11
CNH America LLC reserves the right to make improvements in design or changes in specifications at any time without incurring any obligation to install them on units previously sold. All data given in this publication is subject to production variations. Dimensions and weights are only approximate. Illustrations do not necessarily show products in standard condition.
Page 12
SECTION 1 - SAFETY AND GENERAL INFORMATION SECTION 1 SAFETY AND GENERAL INFORMATION SECTION TABLE OF CONTENTS CHAPTER 1 GENERAL PRECAUTIONS FOR MAKING REPAIRS TABLE OF CONTENTS ..............1-1 GENERAL PRECAUTIONS FOR MAKING REPAIRS .
Page 13
SECTION 1 - SAFETY AND GENERAL INFORMATION NOTES Issued 09-2008 Bur 5-16540 EN-US...
Page 15
SECTION 1 - SAFETY AND GENERAL INFORMATION CHAPTER 1 - GENERAL PRECAUTIONS FOR MAKING REPAIRS CNH America LLC reserves the right to make improvements in design or changes in specifications at any time without incurring any obligation to install them on units previously sold. All data given in this publication is subject to production variations.
SECTION 1 - SAFETY AND GENERAL INFORMATION CHAPTER 1 GENERAL PRECAUTIONS FOR MAKING REPAIRS TABLE OF CONTENTS GENERAL PRECAUTIONS FOR MAKING REPAIRS ..........1-3 Preparation Before Disassembling .
Page 17
SECTION 1 - SAFETY AND GENERAL INFORMATION CHAPTER 1 - GENERAL PRECAUTIONS FOR MAKING REPAIRS NOTES Issued 09-2008 Bur 5-16550 EN-US...
SECTION 1 - SAFETY AND GENERAL INFORMATION CHAPTER 1 - GENERAL PRECAUTIONS FOR MAKING REPAIRS GENERAL PRECAUTIONS FOR MAKING REPAIRS PREPARATION BEFORE DISASSEMBLING 4. Confirm the position of first-aid kit and fire extinguisher, and also where to make contact for 1.
SECTION 1 - SAFETY AND GENERAL INFORMATION CHAPTER 1 - GENERAL PRECAUTIONS FOR MAKING REPAIRS 8. For common parts, pay attention to the quantity 4. For air bleed of travel motor and hydraulic and places. cylinder, starts engine and operate it for 10 minutes or more at no-load and low speed.
SECTION 1 - SAFETY AND GENERAL INFORMATION CHAPTER 1 - GENERAL PRECAUTIONS FOR MAKING REPAIRS 4. Before starting the repair of the attachment, do WARNING not fail to cover the plated surface of the piston rod with flameproof sheet to prevent it from being Battery fluid is dangerous.
SECTION 1 - SAFETY AND GENERAL INFORMATION CHAPTER 1 - GENERAL PRECAUTIONS FOR MAKING REPAIRS INTERNATIONAL UNIT SYSTEM INTRODUCTION Although this manual uses the SI units system. 4. Derived Units bearing Peculiar Designations Outline of SI units system is described here. Table 4 Given below are an excerpt of the units that are related to this manual :...
Page 22
SECTION 1 - SAFETY AND GENERAL INFORMATION CHAPTER 1 - GENERAL PRECAUTIONS FOR MAKING REPAIRS 6. Unit Conversion Table Table 6 QUANTITIES REMARKS Mass Force 1kgf=9.807N Torque kgf/m 1kgf/m=9.807N/m 1kgf/ Pressure kgf/cm =0.098MPa Motive power 1PS=0.7355kW –1 –1 Revolution 1rpm=1min 5-16550 EN-US Issued 09-2008 Bur...
Page 23
SECTION 1 - SAFETY AND GENERAL INFORMATION CHAPTER 1 - GENERAL PRECAUTIONS FOR MAKING REPAIRS NOTES Issued 09-2008 Bur 5-16550 EN-US...
Page 25
SECTION 1 - SAFETY AND GENERAL INFORMATION CHAPTER 2 - SPECIFICATIONS CNH America LLC reserves the right to make improvements in design or changes in specifications at any time without incurring any obligation to install them on units previously sold. All data given in this publication is subject to production variations.
Page 26
SECTION 1 - SAFETY AND GENERAL INFORMATION CHAPTER 2 SPECIFICATIONS TABLE OF CONTENTS SPECIFICATIONS ............... . 2-3 Components Name .
Page 27
SECTION 1 - SAFETY AND GENERAL INFORMATION CHAPTER 2 - SPECIFICATIONS NOTES Issued 09-2008 Bur 5-16560 EN-US...
SECTION 1 - SAFETY AND GENERAL INFORMATION CHAPTER 2 - SPECIFICATIONS SPECIFICATIONS COMPONENTS NAME ARM CYLINDER LIGHT BOOM BOOM CYLINDER BUCKET CANOPY CYLINDER OPERATING LEVER DOZER OPERATING LEVER HYDRAULIC TANK LINK THROTTLE LEVER CONTROL VALVE BUCKET MONITOR PANEL TRAVEL LEVER (GAUGE CLUSTER) SAFETY RADIATOR...
SECTION 1 - SAFETY AND GENERAL INFORMATION CHAPTER 2 - SPECIFICATIONS SPECIFICATIONS AND PERFORMANCE Speed and Gradeability E27BSR Model PV13-33292~ Applicable Machines Rubber shoe Iron shoe (OPT) Shoe Type {rpm} 8.7 (8.7) Slewing Speed Low (1st) High (2nd) Low (1st) High (2nd) km/h (mph) Travel Speed...
SECTION 1 - SAFETY AND GENERAL INFORMATION CHAPTER 2 - SPECIFICATIONS TRANSPORTATION (1)LOADING MACHINE ON A TRAILER 1. Keep trailer bed clean. Put chocks against truck wheels. 2. Use a ramp or loading deck. Ramps must be strong enough, have a low angle, and correct height. Load and unload machine on a level surface.
Page 33
SECTION 1 - SAFETY AND GENERAL INFORMATION CHAPTER 2 - SPECIFICATIONS 3. ARM Model E27BSR L × H × W 1,440 × 400 × 250 (4ft-8.7in × 1ft-3.7in × 9.8in) mm (ft-in) Weight kg (lb) 95 (209) GRAPHIC_1D Figure 6 4.
SECTION 1 - SAFETY AND GENERAL INFORMATION CHAPTER 2 - SPECIFICATIONS TYPE OF CRAWLER SHOES Ground pressure Total Crawler Shoe width Number of kPa (psi) Type Model width mm (in) Link mm (ft-in) CANOPY Rubber shoe 1,500 E27BSR 250 (9.8in) 28 (4.1) 30 (4.4) (4ft-11.1in)
Page 39
SECTION 1 - SAFETY AND GENERAL INFORMATION CHAPTER 3 - ATTACHMENT DIMENSIONS CNH America LLC reserves the right to make improvements in design or changes in specifications at any time without incurring any obligation to install them on units previously sold. All data given in this publication is subject to production variations.
Page 40
SECTION 1 - SAFETY AND GENERAL INFORMATION CHAPTER 3 ATTACHMENT DIMENSIONS TABLE OF CONTENTS ATTACHMENT DIMENSIONS ............. . . 3-3 Boom .
Page 41
This as a preview PDF file from best-manuals.com Download full PDF manual at best-manuals.com...
Need help?
Do you have a question about the E27BSR TIER 4 and is the answer not in the manual?
Questions and answers