Sealey SM31.V3 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instructions
protection
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
9
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products.
Electrical safety information. It is important that the following information is read and understood:
9
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
9
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure
9
Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
9
correct fuse.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable.
8
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or is replaced immediately by
8
qualified electrician.
If the cable or plug is damaged during use, switch off the electricity supply and remove from use.
9
Ensure that repairs are carried out by a qualified electrician.
9
2. INTRODUCTION
Bench mounting semi-portable disc sander suitable for general woodworking applications. Powerful induction motor with smooth direct
drive. Balanced aluminium sanding disc suitable for adhesive backed discs. Includes no-volt load release switch for extra safety. Sanding
disc table tilts to 45° and is supplied with mitre gauge for accurate angle sanding.
3. SPECIFICATION
Model no............................................................................... SM31.V3
Consumable Parts........ Sanding Disc Ø305mm 80Grit PSA(SM31/38
Disc Diameter ..................................................................... ..Ø305mm
Disc Speed............................................................................ .1450rpm
Dust Extraction Diameter....................................................... ..Ø52mm
Fuse Rating....................................................................... .............10A
Motor Power: ...................................................................750W - 230V
Power Supply Cable Length........................................... .................2m
Table Size................................. ......................................156 x 438mm
Table Tilt.............................................................................. ............45º
4. ASSEMBLY
4.1. Unpack the sander and check contents against the list below. If there are any damaged or missing parts contact your supplier immediately.
CONTENTS: • Sander Assembly
4.2. Remove various screws (fig.1 parts1-4) from the sander assembly,fit table (A) in position and retain by replacing screws. The table should
always have at least 1.6mm clearance from the sanding disc adjustment can be made by loosening the six cross head bolts in the face of
the table top.
4.3. If a dust extraction system is available, connect it to the extraction port (diameter 52mm).
4.4. The mitre gauge, when required, locates in the table groove.
WARNING! Before use, the machine must be positioned on a stable, fireproof bench or table which is strong enough to take the weight
‰
of the machine and the workpiece. The sander is supplied with rubber feet, alternatively it can be bolted to a work surface. Failure to
comply with this instruction could result in severe personal injury.
© Jack Sealey Limited
DISC SANDER 305MM
MODEL NO:
Wear protective
Wear ear
gloves
protection
• Table • Mitre Gauge
Original Language Version
SM31.V3
Wear a mask Indoor use only
fig.1
• Hex. Key
SM31.V3 Issue: 6 (1,H,F) 19/09//23