Table of Contents
Advertisement
IMPORTANT: The lighting system in this appliance may consist
of:
Sealed LED modules
■
LED Bulbs
■
Incandescent Bulbs
■
Or a combination of the above.
■
If a Sealed LED module(s) do not illuminate when the refrigerator
and/or freezer door is opened, call for assistance or service. See
"Warranty" for contact information.
If a LED Bulb does not illuminate when the refrigerator and/
or freezer door is opened, replace with like bulb following this
procedure:
1. Unplug the refrigerator or disconnect power.
2. Remove the light shield (on some models).
Remove the hardware holding the light shield in place.
■
Top of the refrigerator compartment - Slide the light shield
■
toward the back of the compartment to release it from the
light assembly.
First try the solutions suggested here. If you need further assistance or more recommendations that may help you avoid a service call,
refer to the warranty page in this manual or visit http://maytag.custhelp.com. In Canada, visit www.maytag.ca.
Contact us by mail with any questions or concerns at the address below:
In the U.S.A.:
Maytag Brand Home Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
The refrigerator will not operate
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Power cord unplugged? Plug into a grounded 3 prong outlet.
■
Is outlet working? Plug in a lamp to see if the outlet is
■
working.
14
Changing the Light Bulb(s)
TROUBLESHOOTING
Refrigerator Operation
3. Replace the burned-out bulb(s) with a bulb of the same size,
shape and wattage.
Order Part Number W10565137 (3.6 W).
■
NOTE: Some LED replacement bulbs are not recommended
for wet/damp environments. The refrigerator and freezer
compartments are considered to be wet/damp environments.
If using a brand of LED bulb other than the recommended LED
bulb, before installation, read and follow all instructions on the
LED packaging.
4. Replace the light shield by inserting the tabs on the shield into
the liner holes on each side of the light assembly. Slide the
shield toward the front until it locks into place.
NOTE: To avoid damaging the light shield, do not force the
shield beyond the locking Point.
5. Replace the hardware that holds the shield in place.
6. Plug in the refrigerator or reconnect power.
If an incandescent bulb does not illuminate when the refrigerator
and/or freezer door is opened, replace with like bulb using the
same procedure outlined above. Replace burned out bulb with
only incandescent bulb(s) of the same size, shape and wattage
(maximum 40 W) designed for household appliances.
In Canada:
Maytag Brand Home Appliances
Customer eXperience Centre
200 – 6750 Century Ave.
Mississauga, Ontario L5N 0B7
Household fuse blown or circuit breaker tripped? Replace
■
the fuse or reset the circuit breaker. If the problem continues,
call an electrician.
Are controls on? Make sure the refrigerator controls are on.
■
See "Using the Controls."
New installation? Allow 24 hours following installation for the
■
refrigerator to cool completely.
NOTE: Adjusting the temperature controls to coldest setting
will not cool either compartment more quickly.
The motor seems to run too much
Your new refrigerator may run longer than your old one due to
its high-efficiency compressor and fans. The unit may run even
longer if the room is warm, a large food load is added, doors are
opened often, or if the doors have been left open.
The refrigerator seems noisy
Refrigerator noise has been reduced over the years. Due to
this reduction, you may hear intermittent noises from your new
refrigerator that you did not notice from your old model. Below
are listed some normal sounds with explanations.
Buzzing - heard when the water valve opens to fill the ice
■
maker
Advertisement
Table of Contents
