Icp-2000 Description; Front Panel Features; Swp-2000 Description - RTS ICP-2000 User Manual

ICP-2000 Description

The ICP-2000 is a 1RU breakout panel that converts
the SCSI type II connection provided from the TM-
2000/MTM-2000 communication card(s) into 9-pin D-
Sub connections. Each RS-485 communication card
on the TM-2000/MTM-2000 has 8 ports provided on
the SCSI type II connector. The ICP-2000 breaks
these 8 ports into individual 9-pin D-Sub connections.
There are two SCSI type II connectors on the ICP-
2000. These two connectors allow both a primary and
redundant TM-2000/MTM-2000 to be connected. The
connectors are wired in parallel, so it does not matter
which connector the primary TM-2000/MTM-2000 and
(if present) redundant TM-2000/MTM-2000 are
plugged into. The ICP-2000's connectors are labeled
from left to right J1, J2, J3....J8. These will correspond
from low number to high number of ports associated
with the cable plugged into the ICP-2000. For ex-
ample: If the cable plugged into an ICP-2000 with ports
1-8 on it, then J1 would be port 1, J2 port 2, up to J8
being port 8. If the cable plugged into an ICP-2000
with ports 9-16 on it, then J1 would be port 9, J2 port
10, up to J8 being port 16. It is important to note that
in systems using VDP panels, port 1 is reserved for
connection to the VDP controller and should not be
connected to an ADAM or ADAM CS.

Front Panel Features

TM
ICP-2000
J1 J2 J3 J4
Figure 3. ICP-2000 front panel features
1. 9-pin female D-sub connector. Each connector is
dedicated to an RS-485 communications port
carried on the SCSI type II cable from the TM-
2000/MTM-2000.
Rear Panel Features
1
Figure 4. ICP-2000 rear panel features.
1. SCSI type II connectors. These are wired in
parallel, so it does not matter which connector is
used with a TM-2000/MTM-2000 even in redun-
dant systems. The SCSI type II cables are
included with the TM-2000/MTM-2000 or with an
add-on RS-485 port card for the TM-2000/MTM-
TELEX COMMUNICATIONS, INC.
MADE IN USA
J5 J6 J7 J8
1

SWP-2000 Description

The SWP-2000 is a 1RU switch over panel that
provides common connections for TrunkEdit and
TrunkSupervisor software packages (via serial
connections to a Windows
toring of both TM-2000/MTM-2000 units and control
of both TM-2000/MTM-2000 units when used in a
redundant configuration.
Front Panel Features
TM A
Activity
Active TM
Power Standby TM
Other TM
Go Active
1
2 3
Figure 5. SWP-2000 front panel features
1. Power LED . Indicates that the SWP-2000 has
power.
2. TM/MTM A Status LEDs . Indications for: Activity,
Active TM/MTM, Standby TM/MTM, Other TM/
MTM. The Activity LED indicates activity on the
TM-2000/MTM2000 associated with the TM/MTM
A inputs. Active TM/MTM LED indicates with TM-
2000/MTM-2000 (either A or B) is active.
Standby TM/MTM LED indicates which TM-2000/
MTM-2000 (either A or B) is in standby. Other
TM/MTM LED indicates green if TM/MTM B is
talking, red if not, and off if the system is not
configured for a backup TM-2000/MTM-2000.
3. TM/MTM A Go Active control switch . Forces the
TM-2000/MTM-2000 associated with the TM A
inputs to become the active trunk master.
4. TM/MTM B Status LEDs . Indications for: Activity,
Active TM/MTM, Standby TM/MTM, Other TM/
MTM. The Activity LED indicates activity on the
TM-2000/MTM-2000 associated with the TM/
MTM B inputs. Active TM/MTM LED indicates
which TM-2000/MTM-2000 (either A or B) is
active. Standby TM/MTM LED indicates which
TM-2000/MTM-2000 (either A or B) is in standby.
Other TM/MTM LED indicates green if TM/MTM A
is talking, red if not, and off if the system is not
configured for a backup TM-2000/MTM-2000.
5. TM/MTM B Go Active control switch . Forces the
TM-2000/MTM-2000 associated with the TM/
MTM B inputs to become the active trunk master.
Rear Panel Features
100-240 VAC
OUTPUT
TRK SPVR
TRK SPVR TRK EDIT
1
2 3 4
Figure 6. SWP-2000 rear panel features.
8
® based PC), status moni-
TM
TM B
Activity SWP-2000
Active TM
Standby TM
Other TM
Go Active
5
4
TM B INPUT TM A INPUT
TRK EDIT PP TRK SPVR TRK EDIT PP
6 7 9
5 8