Page 1
PALM ISLAND 52” CEILING FAN MODEL #50203 Español p. 20 LISTED FOR DAMP LOCATION Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-877-361-3883, Monday - Thursday, 8 am - 6 pm, EST and Friday,...
PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: 1. Canopy 2. Mounting Bracket 3. Canopy Cover 4. Downrod 5. Yoke Cover 6. Motor Housing 7. Switch Housing 8. Light Kit 9. Glass Shade (4) 10.
SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate, or install the product. • Before you begin installing the fan, disconnect the power by removing fuses or turning off the circuit breakers. • Make sure that all electrical connections comply with local codes, ordinances, the National Electrical Code, and ANSI/NFPA 70-199.
MOUNTING OPTIONS DANGER Fig. 1 Turn off the circuit breakers and the wall switch to the fan supply line leads. Failure to disconnect the power supply prior to installation may result in serious injury or death. 1. Your fan has 3 mounting options: •...
MOUNTING BRACKET INSTALLATION 4. Loosen all four mounting bracket screws. Remove Fig. 4 the two canopy screws and washers from the round holes in the canopy. Set aside for later use. Detach Mounting mounting bracket from canopy (Fig. 4). Mounting Bracket Bracket Screws Washer...
STANDARD OR ANGLE MOUNTING INSTRUCTIONS 6. Partially loosen the two set screws in the yoke at Fig. 6 the top of the motor housing (Fig. 6). Set Screws 7. Remove the downrod pin and downrod clip from Fig. 7 the downrod (Fig. 7). Downrod Clip Downrod Pin...
Page 8
STANDARD OR ANGLE MOUNTING INSTRUCTIONS 9. Slide the downrod into the yoke of the motor Fig. 9 Downrod housing, align the holes, and re-install the downrod pin and downrod clip. Then re-tighten the two set screws (Fig. 9). Downrod Downrod Clip Downrod Pin Set Screw...
Page 9
STANDARD OR ANGLE MOUNTING INSTRUCTIONS 12. Install the downrod ball into the mounting bracket Fig. 12 opening. Rotate the fan until the slot in the downrod ball engages the tab in the mounting bracket. The rod should not rotate if installed correctly (Fig.
CLOSEMOUNT INSTRUCTIONS 13. Remove the canopy cover from the bottom of the Fig. 13 canopy (Fig. 13). Helpful Hint: Closemount-style mounting is more suitable for ceilings lower than 8 ft. (2,44 m) high. The downrod and canopy cover are not used in this type of installation.
WIRING CAUTION Fig. 16 Be sure outlet box is properly grounded or that a ground (green or bare) wire is present. Black (live) WARNING White (neutral) If house wires are different colors than referred to in the following step, stop immediately. A professional Bare/Green (ground) electrician is recommended to determine wiring.
CANOPY INSTALLATION 18. Lift the canopy up so the two partially installed Fig. 18 mounting bracket screws are situated in the L-slots on each side of the canopy. Rotate the canopy clockwise and install the remaining mounting bracket screws and washers from Step 4 (Fig. 18). Mounting Mounting Bracket...
BLADE INSTALLATION 19. Remove motor screws from underside of motor and Fig. 19 save for blade arm attachment. Discard the plastic motor blocks and washers but keep the motor screws (Fig. 19). Motor Block Motor Screw Washer Motor Block Motor Screw 20.
LIGHT KIT INSTALLATION 22. (Optional) To install the fan without a light kit: Fig. 22 Remove the three screws and washers from the optional cap. Align holes in optional cap with holes in switch housing. Re-insert screws and washers that were previously removed. Use a Phillips screwdriver (not included) to secure all screws (Fig.
LIGHT KIT INSTALLATION 25. Partially loosen the thumb screws. Then, lift each Fig. 25 glass shade onto the light kit and secure with the thumbscrews (Fig. 25). Note: Do not overtighten the thumbscrews as glass shade may crack or break. Socket Thumbscrew Glass Shade...
OPERATING INSTRUCTIONS 28. Use the fan reverse switch, located on the side Fig. 28 of the light kit, to optimize your fan for seasonal performance (Fig. 28). Using a ceiling fan will allow you to raise your thermostat in the summer and lower your thermostat in the winter without sacrificing comfort.
REPLACEMENT PARTS LIST For replacement parts, call the customer service department at 1-877-361-3883, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday. Model 50203 PIECE DESCRIPTION PART # Blade Arm 50203-A Blade 50203-B Shade 50203-C Loose parts bags containing (not...
TROUBLESHOOTING At least twice each year, lower the canopy to check the downrod assembly, and then tighten all screws on the fan. Clean the motor housing with only a soft brush or lint-free cloth to avoid scratching the finish. Clean the blades with a lint-free cloth. You may occasionally apply a light coat of furniture polish to wood blades for added protection.
Monday - Thursday, 8 am - 6 pm, EST and Friday, 8 am - 5 pm, EST. Please have a copy of the receipt as proof of purchase. The Honeywell Trademark is used under license from Honeywell International Hong Kong China Electric Appliance Manufacture Co., Ltd.