Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Zanussi ZDT21003FA
Summary of Contents for Zanussi ZDT21003FA
- Page 1 User Manual GETTING STARTED? EASY. ZDT21003FA EN User Manual Dishwasher...
-
Page 2: Safety Information
SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. CHILDREN AND VULNERABLE PEOPLE SAFETY This appliance can be used by children aged from 8 years and •... -
Page 3: Safety Instructions
Do not keep the appliance door open without supervision to • prevent to fall on it. Before maintenance, deactivate the appliance and disconnect • the mains plug from the mains socket. Do not use water spray and steam to clean the appliance. •... - Page 4 DISPOSAL WARNING! Risk of injury or suffocation. • Disconnect the appliance from the mains supply. • Cut off the mains cable and discard it. • Remove the door catch to prevent children and pets to get closed in the appliance.
-
Page 5: Easy Start
EASY START On/off button Programme button Programme indicators Half load button Indicators INDICATORS Washing phase. It comes on when the washing phase operates. End indicator. Salt indicator. It is always off while the programme operates. PROGRAMMES Consumption values Degree of soil Programme Programme phases Type of load... -
Page 6: Programme Selection Mode
Consumption values Degree of soil Programme Programme phases Type of load Duration Energy Water (min) (kWh) Fresh soil • Wash 60 °C Crockery and or 65 °C cutlery • Rinses • Prewash 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. -
Page 7: User Mode
Press the programme button until all programme indicators are on (Programme selection mode). With this function you can cancel the running programme. USER MODE While the appliance is in programme selection mode: 1. Press and hold programme button until the indicator starts to flash and the indicator is on. -
Page 8: Activating The Acoustic Signal For The End Of Programme
German degrees French degrees Water softener mmol/l Clarke degrees (°dH) (°fH) level 19 - 22 33 - 39 3.3 - 3.9 23 - 27 15 - 18 26 - 32 2.6 - 3.2 18 - 22 11 - 14 19 - 25 1.9 - 2.5 13 - 17 4 - 10... -
Page 9: Daily Use
working. The washing phase starts only after this procedure is completed. The procedure will be repeated periodically. ADDING SALT Before first use put one litre of water in the salt container. Water and salt can come out from the salt container when you fill it. Risk of corrosion. To prevent it, after you fill the salt container, start a programme. - Page 10 ADDING MULTI-TABLETS • Do not fill the salt container and the rinse aid dispenser. • Adjust the water softener to the lowest level. • Set the rinse aid dispenser to the lowest position. STARTING A PROGRAMME 1. Keep the appliance door ajar. 2.
-
Page 11: Hints And Tips
END OF THE PROGRAMME • Press the on/off button to deactivate the appliance. • Close the water tap. If you do not press the on/off button, after few minutes from the end of the programme all the indicators go off. This helps to decrease the energy consumption. HINTS AND TIPS GENERAL level of the water softener to assure good washing... -
Page 12: Unloading The Baskets
WHAT TO DO IF YOU WANT TO STOP USING • Put cutlery and small items in the cutlery basket. MULTI-TABLETS • Put light items in the upper basket. Make sure that the items do not move. Before you start to use separately detergent, salt •... -
Page 13: Troubleshooting
• Make sure that there are no residues of food or soil in or around the edge of the sump. • Put back in place the flat filter (C). Make sure that it is correctly positioned under the 2 guides. •... -
Page 14: The Washing And Drying Results Are Not Satisfactory
Problem and alarm code Possible solution The programme does not start. • Make sure that the appliance door is closed. • The appliance has started the procedure to re- charge the resin inside the water softener. The dura- tion of the procedure is approximately 5 minutes. The appliance does not fill with water. -
Page 15: Technical Information
TECHNICAL INFORMATION Dimensions Width / height / depth (mm) 596 / 818-898 / 555 Voltage (V) 220 - 240 Electrical connection Frequency (Hz) Water supply pressure Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8) Water supply max 60 °C Cold water or hot water Capacity Place settings... - Page 16 WWW.ZANUSSI.COM/SHOP...