4.1.2 - Mode I procedure, to memorise the FIRST
TRANSMITTER only (transmitter with PRG but -
ton)
01.
ON
2
If no transmitters
are memorised, TT2Z
flashes 2 times
02.
3
PRG
PRG
7 sec
4.1.4 - Mode I procedure, to memorise an ADDITION -
AL TRANSMITTER or a CLIMATE SENSOR (for
transmitters without PRG button)
01.
Wait at least 20 seconds from when the TT2Z is
switched on before initiating this procedure
02.
NEW
10 sec
03.
x 3
OLD
04.
3
x 1
NEW
5.1.2 - Procedure for memorising a transmitter in
Mode II (for transmitters without PRG button)
01.
Wait at least 20 seconds from when the TT2Z is
switched on before initiating this procedure
02.
NEW
10 sec
03.
4
x 1
OLD
04.
In Table B, select
the desired com -
mand
x N
OLD
N = number of button presses indicated in Table B,
next to the selected command.
05.
?
3
NEW
5 sec
? = a desired button, to be associated with the com -
mand selected in Table B.
4.1.3 - Mode I procedure, to memorise an ADDITION -
AL TRANSMITTER or a CLIMATE SENSOR (for
transmitters with PRG button)
01.
Wait at least 20 seconds from when the TT2Z is
switched on before initiating this procedure
02.
2
PRG
3 sec
OLD
5 sec
2
03.
PRG
2
NEW
5 sec
04.
2
PRG
OLD
5.1.1 - Procedure for memorising a transmitter in
Mode II (for transmitters with PRG button)
01.
Wait at least 20 seconds from when the TT2Z is
switched on before initiating this procedure
02.
2
PRG
3 sec
OLD
5 sec
2
03.
PRG
2
NEW
5 sec
04.
In Table B, select
the desired com -
mand
OLD
10 sec
N = number of button presses
(and feedback quantity) indicated
N
in Table B, next to the selected
command.
(feedback)
05.
?
NEW
5 sec
? = a desired button, to be associated with the com -
mand selected in Table B.
TABLE B – Commands available during memorisation of a transmitter button, in Mode
II.
?
Command
Number of but-
Command that is memorised
number
ton presses
No. 1
1 press
Open > Stop > Close > Stop > ...
No. 2
2 presses
Open > Stop > ...
No. 3
3 presses
Close > Stop > ...
No. 4
4 presses
Stop
1(A) - Connections of the outputs for DRY-CONTACT
PRG
1(B) - Connections of the outputs for MECHANICAL MOTORS
(with 3 wires)
PRG
1(C) - Connections of the outputs for 2 independent
SWITCHES
PRG
PRG
5.2.1 - Procedure for DELETING THE ENTIRE MEM-
ORY of the TT2Z device, using a memorised
transmitter (with PRG button)
x N
01.
PRG
x 1
02.
PRG
x 1
03.
PRG
x 1
04.
?
PRG
x 1
05.
PRG
x 1
TABLE A – Pairings that occur automatically between buttons and commands, during memorisation of transmitters in Mode I, in relation to the type of device connected to the TT2Z
and the scheme used for this connection (1A, 1B or 1C).
Motor connection modes
Motor connected with "Dry Contact"
(see scheme 1A)
Motor connected with 3 wires plus the earth wire
("mechanical"-type motor)
(see scheme 1B)
Two independent "Switches"
(see scheme 1C)
Nice
TT2Z
1 - White
2 - White-black
3 - White-orange
Radio receiver
User, installation and safety instructions
www.niceforyou.com
5.2.2 - Procedure for DELETING THE ENTIRE MEM-
ORY of the TT2Z device, using a NON-memo-
rised transmitter (with PRG button)
01.
OFF
2
(TT2Z)
5 sec
2
02.
within 10 seconds:
2
3
NEW
5 sec
03.
OFF
4
(TT2Z)
5 sec
5
04.
continue the procedure by completing all the
steps of the procedure indicated in Paragraph
5.2.1
Transmitter button
s
n
t
s
n
t
s
n
t
IS0487A01MM_24-08-2017
EN
Nice S.p.A.
Via Pezza Alta, 13
31046 Oderzo (TV), Italy
info@niceforyou.com
ON
(TT2Z)
ON
(TT2Z)
Memorised command
Command: UP
Command: STOP
Command: DOWN
Command: UP
Command: STOP
Command: DOWN
Switching On / Off of SWITCH 1
Switching off of SWITCH 1 and of SWITCH 2
Switching On / Off of SWITCH 2
Need help?
Do you have a question about the TT2Z and is the answer not in the manual?
Questions and answers