Package Contents; Safety Instructions - UNIVIEW IPC67 Series Instructions Manual

3

Package Contents

4

Safety Instructions

Installation and disassembly of the camera and its accessories must be carried out by a qualified person. Before installation and operation, study the safety instructions.
4.1
Installation and Shipping Notice
Make sure that the length of the DC power cord between the power adapter and the camera is not too long, otherwise the voltage of the camera is reduced. The camera may not


 When connecting to an external interface, use the connection terminal and make sure that the cable terminal (or ethernet connector latch) is in good condition and properly clicked
Make sure that the cable is not overly tensioned during assembly to avoid bad contact with the port or loosening caused by shock or shock.
During transportation , special care should be taken to protect the transparent dome cover/camera visor from friction, scratches, chemical splashes, etc. Do not remove the protective

Contact the experts for maintenance information. Do not try to dismantle the device yourself. We assume no liability for problems caused by unauthorized repair or maintenance.

4.2
Maintenance
 Remove dust and small debris from the camera using lower pressure compressed air (blower) or a fine brush to avoid scratching the camera dome/visor.
 If there is grease or dust stain on the glass surface, gently clean the glass surface from the centre outwards using antistatic gloves or an optic cloth. If grease or stain still remains, use
5
Involvement
• Power supply: After installing the camera, connect the power adapter (not included unless otherwise stated) and the ethernet cable to your router, or when powering with IEEE802.3af
• Alarm input / output: If the camera is equipped with a digital input and output, and unless otherwise stated, the digital input is activated by connecting to GND, the digital output is a
• Audio: if the camera is equipped with an Audio IN / OUT audio interface, the parameters are as follows (unless otherwise stated): Input-impedance 35kΩ; amplitude 2V [p-p], Impedance
6
Camera access
1.
Open the IE web browser, type the IP address of the camera in the address bar and press Enter. The default IP address is 192.168.1.13 (the subnet mask is 255.255.255.0).
2.
On the login page, enter the default username and password (admin/123456) and click Log In. After logging in, you will see a live preview of the camera.
By default, dhcp is enabled for the camera. If a DHCP server is used on

your network, your camera may be assigned a different IP address by
your router and you must use the assigned IP address to log in. The best
way to find out the IP address is to use the
Možná will have to install a plug-in in the IE browser the first time you log

in. Follow the on-screen instructions to complete the installation, and
then reopen the browser to sign in.
The default password is only for your first login. For security, change your

password after the first login. We strongly recommend that you set a
strong password of at least nine characters, including all three elements:
numbers, letters, and special characters.
If your password has been changed, sign in with your new password.

Item
Camera
Drill template
Bag with installation accessories
Use the recommended power adapter or IEEE802.3af PoE device. Otherwise, the device may be damaged.

If it is necessary to extend the power cord, extend the cable between the power adapter and the 230V network.

During installation, do not bend and break the cables too much, otherwise poor cable contact may cause a malfunction.
film from the camera dome/visor until installation is complete.
antistatic gloves or an optic cloth soaked in detergent and gently clean the surface of the glass until clean.
 Do not use organic solvents (such as benzene and alcohol) to clean the transparent dome cover.
PoE to your PoE switch / NVR Uniview (connection option without power adapter, the camera must support PoE).
MAX dry contact. 30, VDC, 1A or 50 VAC, 0.3A.
NOTE!
Uniview Eztools desktop
application.
6 z 36
Quantity
1
1
1
work properly.
output 600Ω; amplitude 2V [p-p].