Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Suunto Memory Belt
Summary of Contents for Suunto Memory Belt
-
Page 2: Table Of Contents
SUUNTO MEMORY BELT ... 7 4. ERRORS AND WARNINGS ... 10 5. INSTALLING SUUNTO SOFTWARE ... 15 6. USING SUUNTO MEMORY BELT WITH OTHER SUUNTO DEVICES ... 15 7. TECHNICAL SPECIFICATIONS ... 17 8. INTELLECTUAL PROPERTY ... 17 9. DISCLAIMERS ... 18... -
Page 3: Introduction To Suunto Memory Belt
Suunto PC software and receive detailed information based on heart rate variation. As a transmitter, the Suunto Memory Belt is ideal for team sports in which watches and jew- elry are banned or impractical. Operating on a secure, 2.4 GHz frequency, the Suunto Mem- ory Belt transmits real-time heart rate information to a coach, trainer or researcher for immediate analysis during workout. - Page 4 The symbols in the beep and flash columns indicate the length of the signal (short, medium-length or long). NOTE: Suunto Memory Belt can give two long beeps for three different reasons. In this case, check the color of the flash to find out the correct cause.
- Page 5 PUTTING ON SUUNTO MEMORY BELT To get the best results from your Suunto Memory Belt, it is important that you wear it cor- rectly. To put it on, just follow the simple steps below: 1. Put on your Suunto Memory Belt and ensure it fits snugly against your chest.
- Page 6 If the beep and green flash do not occur when you have put the Suunto Memory Belt on, make sure that the belt fits snugly and that the electrodes are wet. If the orange or red light flashes, the memory or battery is low.
-
Page 7: Downloading And Analyzing Data Recorded With Suunto Memory Belt
After training, when you take off the Suunto Memory Belt, 2 long beeps and 2 long green flashes will indicate that the device hasn’t received data for 30 seconds. After 60 seconds, the device will stop recording and transmitting, then go into sleep mode, which is indicated by 3 short beeps and 3 short green flashes. - Page 8 DOWNLOADING AND ANALYZING DATA Use the PC software to start transferring the data from the Suunto Memory Belt. You can then view the data in graphical form and analyze it in more detail using Suunto Team Man- ager or Suunto Training Manager PC software.
- Page 9 CUSTOMIZING YOUR SUUNTO MEMORY BELT You can use your PC to adjust your Suunto Memory Belt settings. You can make the follow- ing adjustments to the belt’s functionality through the PC interface: • Switch the belt’s own recording function on or off. (Turning off recording also turns off all sound and light signals, and the belt works as a normal heart rate belt for Suunto ANT- compatible devices.)
-
Page 10: Errors And Warnings
Suunto Memory Belt. This signal continues until you take off the belt. If you don’t need to transmit data with your Suunto Memory Belt, it is worth turning off the belt’s transmitting function with the PC software, as transmitting data has a significant impact on battery... - Page 11 This is followed by a flash every 4 seconds, which indicates that you should download your data to your PC and empty the belt’s memory. However, as the memory is low, not full, Suunto Memory Belt will continue recording normally.
- Page 12 Suunto Memory Belt to record heart rate data. NO HEART RATE DETECTION If, during recording, Suunto Memory Belt no longer detects your heart rate, it will alert you by 2 long beeps and 2 long, green flashes every 30 seconds. As long as there is available mem- ory, the device will continue to give this warning every 30 seconds while in contact with the skin.
- Page 13 REPLACING THE BATTERY The transmitter belt operates on a 3-Volt lithium cell, type: CR 2032. The average expected battery life of the transmitter belt is 300 hours of use in ideal operating temperatures. To replace the battery: 1. Insert a coin into the slot located on the battery compartment cover on the backside of the transmitter belt.
- Page 14 NOTE: If the Suunto Memory Belt has been stored in a cold place, it may give a low battery warning even though the battery has enough power left. In such cases, allow the device to warm up in room temperature for 15 minutes and then activate it again.
-
Page 15: Installing Suunto Software
5. INSTALLING SUUNTO SOFTWARE INSTALLING THE SOFTWARE NOTE: Do not plug the Memory Belt docking station into the PC before the installation has been completed. 1. Insert the Suunto software CD-ROM into the drive. 2. Wait for the installation to begin and follow the installation instructions. - Page 16 TRANSMITTING AND ANALYZING DATA Suunto Memory Belt Suunto Memory Belt can be used for real-time heart rate transmission to a number of HR belt. You can use Suunto t-series compatible heart rate monitors with Suunto Memory Belt to see your heart rate instantly.
-
Page 17: Technical Specifications
60 bpm heart rate, or 1 day with a 120 bpm heart rate) 8. INTELLECTUAL PROPERTY COPYRIGHT This publication and its contents are proprietary to Suunto Oy and are intended solely for the use of its clients to obtain knowledge and information regarding the operation of Suunto prod- ucts. -
Page 18: Disclaimers
9. DISCLAIMERS USER’S RESPONSIBILITY This instrument is intended for recreational use only. Suunto Memory Belt must not be used as a substitute for obtaining measurements that require professional precision and must not be used to obtain measurements that require laboratory-quality measurements. - Page 19 LIMITS OF LIABILITY AND ISO 9001 COMPLIANCE If this product should fail due to defects in materials or workmanship, Suunto Oy will, at its sole option, repair or replace it with new or rebuilt parts, free of charge, for two (2) years from the date of its purchase.
-
Page 20: Disposal Of The Device
10. DISPOSAL OF THE DEVICE Please dispose of the device in an appropriate way, treating it as electronic waste. Do not throw it in the garbage. If you wish, you may return the device to your nearest Suunto representative.