Suunto iQniter User Manual

TROUBLESHOOTING
GET SOCIAL!
CHECK YOUR BELT
Electrodes must be moist and in proper contact with skin. Unstable HR signals
#iqniter ■
may be due to dry skin contact with belt. In some cases it may be necessary to
move the strap a bit to get connected.
Ill-fitting strap, too lose against skin and electrode loses contact with skin
■
Strap not over heart, ensure sensor is in center of chest and electrodes in
■
contact with skin directly under breast line
Strap can provide years of use if properly cared for, however it will wear and
■
need replacing
Low battery (life is approximately 200 hours with normal use)
■
Damaged Sensor contacts (with care remove one contact at a time, don't push
■
the sensor/transmitter from the belt)
The elastic strap has a max strench of 15 %. Different strap sizes are available.
■
TROUBLESHOOTING IN THE GYM
For troubleshooting when you use the iQniter Smart Sensor together with iQniter
Cardio Training in the gym, please follow this additional guide line:
1 Check that the sensor ID is correctly registered at my.iqniter.com or in the
AdmiQ-registrationprogram at the gym.
2 Cardio Training related troubleshooting (consult the instructor or reception in
the gym. Refer to installation guide at www.iqniter.com.)
Please note that iQniter Cardio Training only works with "Q" Smart Sensors
(white front). Suunto Smart Sensors (black front) are not applicable.
#iqniter
BATTERY SAFETY
The iQniter Smart Sensor uses a 3-Volt lithium cell CR2025. With Suunto WARNING: Only for recreational use.
Movescount App, you can check the battery status from the device information
when the iQniter Smart Sensor is paired. WARNING: Always consult your doctor before beginning an exercise program.
Overexertion may cause serious injury.
REPLACING THE BATTERY
1 Remove the sensor firmly from the belt
WARNING: Allergic reactions or skin irritations may occur with any product
2 Open the battery cover
that is in contact with skin, even though our products comply with all industry
3 Replace the battery (Smart Sensor CR2025). Ensure that the battery switch
standards. In such event, stop use immediately and seek medical attention.
(red arrow 3) is NOT UNDER the battery.
4 Place the new cover with sealing ring. First inset the cover in the battery
WARNING: People who have a pacemaker, defibrillator, or other implanted
switch side (red arrow 4)
electronic device use the transmitter belt at their own risk. Before starting
5 Firmly close the battery cover (red arrow 5)
the initial use of the heart rate belt, we recommend an exercise test under a
Note: We recommend always to use a new cover to ensure a prober sealing doctor's supervision. This will ensure the safety and reliability of the pacemaker
when replacing battery and heart rate belt when being used simultaneously. Exercise may include
some risk, especially for those who have been sedentary. We strongly advise
you to consult your doctor prior to beginning a regular exercise program.
3 4 5
CARE AND SUPPORT COMPLIANCE
CAUTION: Do not pull the iQniter NOTE: Dry skin under the belt EU radio directive
Smart Sensor module off the belt. electrodes, a loose belt, and synthetic Hereby, Suunto Oy, declares that the
This may damage the belt connectors. shirt materials can cause abnormally radio equipment type MOVESENSE is
Unsnap one side at a time. high heart rate readings. Moisten the in compliance with Directive 2014/53/
belt electrodes well and tighten the EU. The full text of the EU declaration
CAUTION: Do not machine wash belt to avoid heart rate peaks. If you of conformity is available at the
the iQniter Smart Sensor module. are otherwise concerned about your following internet address:
Machine washing damages the heart rate, please consult a doctor. www.Suunto.com/EUconformity.
module.
NOTE: When changing battery, we FCC
NOTE: Both the iQniter Smart Sensor strongly recommend using a new This device complies with Part 15 of
module and belt should be rinsed original cover to ensure proper the FCC Rules. Operation is subject
with fresh water after each use. The sealing and avoid moist inside the to the following two conditions: (1)
belt should be machine washed sensor this device may not cause harmful
in 40º C after every 2-3 exercises. interference, and (2) this device must
See the belt tag for further washing NOTE: Limited warranty 1 year. For accept any interference received,
instructions. personal use only. I case the usage including interference that may
pattern holds multi-user application, cause undesired operation. This
NOTE: You do not need to replace the the warranty is void. product has been tested to comply
iQniter Smart Sensor module; only with FCC standards and is intended
the Suunto Smart Sensor belt strap for home or office use. Changes or
may eventually need replacing after modifications not expressly approved
extended use. by Suunto could void your authority
to operate this device under
FCC regulations.
IC
This device complies with Industry
Canada licence-exempt RSS
standard(s). Operation is subject to
IQNITER SMART SENSOR
the following two conditions: (1) this
device may not cause interference,
and (2) this device must accept any
USER GUIDE
interference, including interference
that may cause undesired operation
of the device.
Cet appareil est conforme aux
normes RSS hors licence d'Industrie
Canada. Son utilisation est soumise
aux deux conditions suivantes:
(1) cet appareil ne doit pas causer
d'interférences, (2) cet appareil
doit accepter toute interférence, y
compris les interférences pouvant
entraîner un fonctionnement non
désiré de l'appareil.
© Suunto Oy 2018. All rights reserved.
Suunto is a registered trademark of Suunto Oy.