Related Manuals for Siemens SN85Z802BE
Summary of Contents for Siemens SN85Z802BE
- Page 1 SN85Z802BE Dishwasher EN Information for Use Register your appliance on My Siemens and discover exclusive services and offers. Siemens Home Appliances...
-
Page 2: Table Of Contents
Further information and explanations are available online: Table of contents 1 Safety ........... 4 7 Programmes ...... 19 1.1 General information.... 4 7.1 Information for test institutes ... 20 1.2 Intended use...... 4 7.2 Favourite ...... 20 1.3 Restriction on user group.. 4 7.3 Intelligent ...... - Page 3 13 Detergent ......... 30 20 Transportation, storage and disposal ........ 53 13.1 Suitable detergents .... 30 20.1 Removing the appliance .. 53 13.2 Unsuitable detergents ... 31 20.2 Protect appliance from frost.. 54 13.3 Information on detergents .. 32 20.3 Transporting the appliance ... 54 13.4 Adding detergent....
-
Page 4: Safety
en Safety 1 Safety Observe the following safety instructions. 1.1 General information Read this instruction manual carefully. ¡ Keep the instruction manual and the product information safe ¡ for future reference or for the next owner. Do not connect the appliance if it has been damaged in transit. ¡... - Page 5 Safety en WARNING ‒ Risk of electric shock! Incorrect installation is dangerous. Connect and operate the appliance only in accordance with the ▶ specifications on the rating plate. Always use the supplied power cable for the new appliance. ▶ Connect the appliance to a power supply with alternating cur- ▶...
-
Page 6: Safe Use
en Safety Contact between the appliance and installation lines may lead to a defect in these lines, e.g. gas pipes and power lines. Gas from a corroded gas pipe can ignite. A damaged power line can cause a short circuit. Check that there is a distance of at least 5 cm between the ap- ▶... - Page 7 Safety en Highly caustic alkaline or highly acidic cleaning agents in conjunc- tion with aluminium parts in the interior of the appliance may cause explosions. Never use highly caustic alkaline or highly acidic cleaning ▶ agents, in particular commercial or industrial products, in con- junction with aluminium parts (e.g.
-
Page 8: Damaged Appliance
en Safety WARNING ‒ Risk of burns! The blow opening of the Zeolith container becomes hot and can cause burns. Never touch the blow opening of the Zeolith container. ▶ 1.6 Damaged appliance WARNING ‒ Risk of electric shock! If the appliance or the power cord is damaged, this is dangerous. Never operate a damaged appliance. -
Page 9: Safety Systems
Safety en Children may become trapped in the appliance and suffocate. Use the childproof lock if fitted. ▶ Never let children play with or operate the appliance. ▶ WARNING ‒ Risk of harm to health! Children can lock themselves in the appliance, thereby putting their lives at risk. -
Page 10: Preventing Material Damage
en Preventing Modified or damaged water hoses Preventing 2 Preventing material may result in material damage and damage to the appliance. damage Never kink, crush, modify or cut ▶ through water hoses. Preventing 2.1 Safe installation Only use the water hoses supplied ▶ with the appliance or genuine ATTENTION! spare hoses. -
Page 11: Childproof Lock
Childproof lock en So as not to scratch the finish on ▶ 4 Environmental protec- the appliance, do not use sponges with a rough surface or abrasive tion and saving energy cleaning agents. To prevent corrosion, do not use ▶ sponge cloths on dishwashers with 4.1 Disposing of packaging a stainless steel front or rinse such The packaging materials are environ-... -
Page 12: Sensors
en Installation and connection During the drying phase moisture Sensor set- Description from the interior of the dishwasher is ting stored in the mineral and heat energy SE:02 Adjusts the pro- is released. The heat energy is blown gramme strength for out into the interior of the dishwasher difficult conditions of with dry air. -
Page 13: Installing And Connecting The Appliance
Installation and connection en Installation material ¡ 5.3 Drainage connection Steam guard plate ¡ Connect your appliance to drainage Salt filling aid funnel ¡ connection so dirty water is dis- Mains cable ¡ charged via the wash cycle. Quick reference guide ¡ Installing the drainage connection 5.2 Installing and connecting Consult the installation instructions... -
Page 14: Electrical Connection
en Installation and connection 5.5 Electrical connection Connecting the appliance to the electricity supply Notes Follow the Safety instructions ¡ → Page 4. Please note that the water safety ¡ system is only functional if there is a power supply. Insert the non-heating appliance plug of the power cable into the appliance. -
Page 15: Familiarising Yourself With Your Appliance
Familiarising yourself with your appliance en 6 Familiarising yourself with your appliance 6.1 Appliance You can find an overview of the parts of your appliance here. Rating plate Rating plate with E number and FD num- ber → Page 55. The data you need for Customer Service → Page 54. - Page 16 en Familiarising yourself with your appliance Detergent dispenser Add detergent to the detergent dispenser. → "Detergent", Page 30 Bottom basket Bottom basket → Page 24 Dispenser for special salt Add special salt to the dispenser for spe- cial salt. → "Water softening system", Page 27 Lower spray arm The lower spray arm washes the table- ware in the bottom basket.
-
Page 17: Controls
Familiarising yourself with your appliance en 6.2 Controls You can use the control panel to configure all functions of your appliance and to obtain information about the operating status. With some buttons you can perform different functions. 3 4 5 6 ON/OFF button and reset Switching on the appliance button... -
Page 18: Programmes
en Familiarising yourself with your appliance Start button Starting the programme → Page 36 Programme buttons and addi- Programmes tional functions → "Programmes", Page 19 Additional functions → "Additional functions", Page 22 Door handle Open the appliance door. → Page 35 Display The display shows information about the remaining running time or the ba- sic settings. - Page 19 Programmes en 7 Programmes You can find an overview of the pro- ted. The running time will change if grammes that can be selected here. the rinse aid system is switched off Different programmes, which can be or rinse aid needs to be added. found on the control panel of your The consumption values can be appliance, are available depending...
-
Page 20: Information For Test Institutes
en Programmes Programme Programme se- quence Tableware: Time-optimised: Mixed tableware and cutlery Cleaning 60 °C ¡ ¡ Speed 60° Level of soiling: Intermediate rinse ¡ Common household food rem- Final rinse 50 °C ¡ ¡ nants lightly dried on ¡ Tableware: Particularly gentle: Cleaning delicate tableware, Pre-Rinse ¡... -
Page 21: Intelligent
Programmes en Press the right programme button. Press the button for the relevant additional function. Press for 3 seconds. The selected programme and the additional function will flash. flashes. The programme and the additional function are saved. Tip: To reset the programme to the pre-rinse programme stored at the factory, use the Home Connect app or reset your appliance to the factory... -
Page 22: Additional Functions
en Additional functions 8 Additional functions You can find an overview of the additional functions that can be selected here. Different additional functions, which can be found on the control panel of your appliance, are available depending on the appliance configuration. You can se- lect certain additional functions depending on the programme. -
Page 23: Top Basket
Features en Raise or lower the basket evenly to 9.1 Top basket the right level. Arrange cups, glasses and small items of tableware in the top basket. Check that the basket is level on both sides. Release the levers. Knife shelf The basket clicks into position. You can adjust the height of the top Slide the basket back in. -
Page 24: Etagere
en Features 9.3 Etagere Use the cutlery shelf and space un- derneath for small cups and glasses or for large items of cutlery, e.g. cooking spoons or serving cutlery. 9.5 Folding prongs Use the folding prongs to position tableware securely, e.g. plates. If you do not need the cutlery shelf, you can fold it up. -
Page 25: Cutlery Basket
Features en Push the lever forwards and fold 9.7 glassZone down the prongs . Use the glassZone in the top basket to clean all types of glasses gently yet thoroughly. To use the prongs again, fold them back up. The prongs audibly click into posi- tion. -
Page 26: Before Using For The First Time
en first time Pull the tab on the glassZone up first time 10 Before using for the and forwards . first time first time 10.1 Performing the initial configuration On initial start-up or after a reset to the factory settings, you will need to make settings. -
Page 27: Water Softening System
Water softening system en To ensure good dishwashing results, 11 Water softening sys- you can treat the water with special salt and the water softening system. To avoid damage to the appliance, water with a hardness above 9 °E Hard water leaves limescale on the must be softened. -
Page 28: Special Salt
en Water softening system To save the settings, press Note: Only use special salt for for 3 seconds. dishwashers. Do not use salt tablets. Do not use table salt. 11.3 Special salt Add the special salt to the dis- You can use special salt to soften penser. -
Page 29: Regeneration Of The Water Softening System
Rinse aid system en The water hardness is 0 - 8 °E. ¡ Additional power consump- 0.05 You do not need to use special tion in kWh salt. The consumption values specified Press . are laboratory measurements determ- To open the basic settings, press ined in accordance with the currently for 3 seconds. -
Page 30: Setting The Amount Of Rinse Aid
en Detergent Add rinse aid up to the max mark. To save the settings, press for 3 seconds. 12.3 Switching the rinse aid system off If you find the rinse aid refill indicator irritating, e.g. when using combined detergents with a rinse aid compon- ent, you can switch the rinse aid sys- tem off. -
Page 31: Unsuitable Detergents
Detergent en starch and remove protein. Oxygen- With powder and liquid detergent the based bleaching agents are generally dosage can be individually adjusted used to remove coloured marks, e.g. to the level of soiling of the table- tea or ketchup. ware. For better washing and drying results Note: Follow the manufacturer's in- and to avoid damage to the appli-... -
Page 32: Information On Detergents
en Detergent Add the detergent to the dry deter- 13.3 Information on deter- gent dispenser. gents Follow the instructions on detergents 50 ml in everyday use. 25 ml Detergents marked as "organic" or ¡ 15 ml "ecological" (environmentally friendly) generally contain lower levels of active agents or com- pletely dispense with certain sub- stances. -
Page 33: Tableware
Tableware en Close the lid of the detergent dis- 14.1 Damage to glass and penser. tableware Only put glasses and china in the dishwasher if it is marked as dish- washer-safe by the manufacturer. Avoid damage to glass and table- ware. Cause Recommenda- tion The following... -
Page 34: Arrange Tableware
en Tableware For better washing and drying res- ¡ Cause Recommenda- ults, position items with curves or tion recesses at an angle so water can Highly caustic al- If you are using run off. kaline or highly highly caustic al- acidic cleaning kaline or highly solutions, in par- acidic cleaning... -
Page 35: Removing Tableware
operation en If the childproof lock is activated, press on the upper middle section of the appliance door twice with a short interval in between. The appliance door will open auto- matically. 15.2 Switching on the appli- ance Press . ▶ The Eco 50°... -
Page 36: Setting Timer Programming
en operation Press the button for the relevant will help prevent excess pressure ▶ additional function. building up in the appliance and stop the appliance door bursting open. → "Additional functions", Page 22 The additional function is set and Open the appliance door carefully. the additional function button Press ... -
Page 37: Basic Settings
Basic settings en 16 Basic settings You can configure the basic settings for your appliance to meet your needs. 16.1 Overview of the basic settings The basic settings depend on the features of your appliance. Basic setting Display text Selection Description Water hardness H:04 H:00 - H:07 Set the water softening sys-... - Page 38 en Basic settings Basic setting Display text Selection Description EmotionLight EL:01 EL:00 - EL:02 Interior light. With the setting "EL:00"m ¡ the interior light is switched off. With the setting "EL:01", ¡ the interior light can be activated via the ON/OFF button.
- Page 39 Basic settings en Basic setting Display text Selection Description Start programme SP:01 SP:00 - SP:01 Set a default programme for when the appliance is switched on. With the setting "SP:00", ¡ the last programme selec- ted is set by default when the appliance is switched With the setting "SP:01", ¡...
-
Page 40: Changing Basic Settings
en Home Connect Basic setting Display text Selection Description Remote Start rc:01 rc:00 - rc:02 Activate or deactivate → "Remote Start ", Page 41. The following settings are possible: With the setting "rc:00", ¡ the function is perman- ently deactivated. With the setting "rc:01", ¡... -
Page 41: Home Connect Quick Start
Home Connect en depends on the availability of Start the Home Connect app and Home Connect services in your coun- set up access for Home Connect. try. You can find information about The Home Connect app guides this at: www.home-connect.com. you through the entire login pro- To be able to use Home Connect, cess. -
Page 42: Data Protection
en Cleaning and servicing Note: Please note that the Requirements The appliance is connected to your Home Connect functions can only be ¡ WLAN home network. utilised with the Home Connect app. The appliance is connected to the Information on data protection can be ¡... -
Page 43: Tips On Appliance Care
Dishwasher Care and Ma- ance to malfunction. To avoid such chine Cleaner for Dishwashers online faults and reduce odours, we recom- at https://www.siemens-home.bsh- mend cleaning your appliance at reg- group.com/store or from customer ular intervals. service. -
Page 44: Filter System
en Cleaning and servicing Make sure that there are no alu- ¡ 18.5 Filter system minium parts, e.g. extractor hood The filter system removes coarse grease filters or aluminium pans, in soiling from the dishwashing cycle. the interior of the appliance. If you have not run Machine Care ¡... -
Page 45: Cleaning Spray Arms
Cleaning and servicing en Pull down the micro filter to re- Insert the filter system into the ap- move. pliance and turn the coarse filter clockwise. Make sure that the arrow mark- ‒ ings match up. Press the locking catches gether and lift the coarse filter out ... - Page 46 en Cleaning and servicing Pull up the lower spray arm to re- Check the outlet nozzles on the move. spray arms for blockages under running water and remove any for- eign bodies. Insert the lower spray arm. The spray arm clicks into position. Insert the upper spray arm and screw it firmly in place.
-
Page 47: Troubleshooting
This will avoid unneces- sary costs. Tip: You can find further information and explanations on troubleshooting on- line by scanning the QR code in the table of contents and on our website siemens-home.bsh-group.com. WARNING Risk of electric shock! Incorrect repairs are dangerous. - Page 48 en Troubleshooting Fault Cause and troubleshooting E:32-00 will light up Remove the filter from the supply hose alternately or indicator for water supply lights Clean the filter. Re-insert the filter in the supply hose. Screw the water connection back on. Check the water connection for leaks. Restore the power supply.
- Page 49 Troubleshooting en Fault Cause and troubleshooting E:61-03 will light up Not an appliance fault. Siphon connection is still alternately. Water is closed or the wastewater hose is kinked or blocked. not drained. Check the connection to the siphon and open if ne- cessary.
- Page 50 en Troubleshooting Fault Cause and troubleshooting All LEDs lit up or Electronics have detected a fault. flashing. Press the main switch button for approx. 4 seconds. The appliance is reset and restarted. If the problem occurs again: Switch off the appliance. ‒ Pull out the mains plug or switch off the fuse in ‒...
- Page 51 Troubleshooting en Fault Cause and troubleshooting Remnants of food on Filters are inserted incorrectly and/or not engaged. tableware. Insert the filters properly. → "Filter system", Page 44 Engage the filters. Washing programme selected too weak. Select a more intensive washing programme. ▶ → "Programmes", Page 19 Adjust the sensitivity of the sensors.
- Page 52 en Troubleshooting Fault Cause and troubleshooting Removable streaks Tableware has been precleaned too intensely. The are present on sensors chose a weaker programme. Stubborn soiling glasses, glassware cannot be entirely removed. with a metallic appear- Only remove large remnants of food and do not ▶...
-
Page 53: Clean Wastewater Pump
Transportation, storage and disposal en Insert the pump cover and press 19.1 Clean wastewater pump down . Large remnants of food or foreign bodies can block the waste water pump. As soon as the rinsing water no longer drains properly, the waste water pump must be cleaned. -
Page 54: Protect Appliance From Frost
en Customer Service 20.2 Protect appliance from 20.4 Disposing of old appli- frost ance If there is a risk of frost where the ap- Valuable raw materials can be re- pliance will be standing, e.g. in a holi- used by recycling. day home, empty the appliance com- pletely. -
Page 55: Customer Service
Customer Service en Customer Service for a period of at 21.2 AQUA-STOP guarantee least 10 years from the date on In addition to warranty claims against which your appliance was placed on the seller under the purchase agree- the market within the European Eco- ment and in addition to our manufac- nomic Area. -
Page 56: Technical Specifications
en Technical specifications 22 Technical specifications Weight Max.: 60 kg Voltage 220 - 240 V, 50 Hz or 60 Hz Power rating 2000 - 2400 W Fuse 10 - 16 A Water pressure min. 50 kPa (0.5 bar) ¡ max. 1000 kPa (10 bar) ¡ Inlet rate Min. 10 l/min Water temperature Cold water. Hot water max.: 60 °C Capacity 13 place settings You can find more information about... -
Page 57: Declaration Of Conformity
BSH Hausgeräte GmbH hereby de- A detailed Declaration of Conformity clares that the appliance with Home can be found online at siemens- Connect functionality conforms to the home.bsh-group.com/uk/ among the essential requirements and other rel- additional documents on the product evant provisions of Directive page for your appliance. - Page 60 EN Manufactured by BSH Hausgeräte GmbH under the trademark licence of Siemens AG Valid within Great Britain: Imported to Great Britain by BSH Home Appliances Ltd. Grand Union House Old Wolverton Road Wolverton, Milton Keynes MK12 5PT United Kingdom BSH Hausgeräte GmbH Carl-Wery-Straße 34...