Siemens SN85TX00CE Quick Reference Manual

en
Before using for the first time, read the operating instructions.
Setting up Home Connect
Tip: Connect your appliance to a mobile device. You can con-
veniently change all settings via the Home Connect app.
1. Install the Home Connect app on your mo-
bile device and follow the instructions.
2. Scan the QR code using the Home Con-
nect app.
How to use your appliance
1. Load the tableware.
Only clean tableware that is suitable for dish-
washers. Remove large remnants of food from
the tableware. Check that the spray arms can ro-
Overview of water hardness settings
You can find an overview of the
water hardness values that can
be selected here.
A table of country-specific units
can be found in the instruction
manual.
Hardness mmol/l Setting
range value
Soft 0 - 1.1 H:00
Soft 1.2 - 1.4 H:01
Adding special salt
To avoid damage to the appliance, only add special
salt to the dispenser for special salt just before the
programme starts.
1. Unscrew the lid of the dispenser for special salt
and remove.
On initial start-up: Fill the dispenser right up with
2.
water.
Adding rinse aid
1. Press the catch on the lid
of the dispenser for rinse
aid and lift ⁠ .
Adding detergent
1. Add the detergent to the
dry detergent dispenser.
tate freely.
2. Add detergent.
3. Switch on the appliance ⁠ .
Setting the water softening sys-
tem
Medium 1.5 - 1.8 H:02
Medium 1.9 - 2.1 H:03 1. Press
Medium 2.2 - 2.9 H:04 2. To open the basic settings, press
Hard 3.0 - 3.7 H:05
a The display shows H:xx.
Hard 3.8 - 5.4 H:06
a The display shows
Hard 5.5 - 8.9 H:07
3. Press
right water hardness has been set.
4. To save the settings, press
3. Add the special salt to the
dispenser. The water in the
dispenser is displaced and
forced out. Never add de-
tergent.
4. Place the lid back on the dispenser and turn to
close.
2. Add rinse aid up to the
max mark.
2
1
3. Close the lid of the dispenser for rinse aid.
a The lid clicks into position.
2. Close the lid of the deter-
50 ml
25 ml gent dispenser.
15 ml
a The lid clicks into position.
4. Select the programme.
5. Start the programme ⁠ .
Remove the tableware at the end of the pro-
6.
gramme.
Programmes
The programme data has been meas-
ured in the laboratory according to
⁠ .
European standard EN 60436.
The consumption figures depend on
for 3 seconds.
the programme and additional func-
tion selected.
⁠ .
The runtime will change if the rinse
or repeatedly until the
aid system is switched off or rinse aid
needs to be added.
for 3 seconds.
Programme
Intensive 70°
Auto 45-65°
Eco 50°
Silence 50 1
brilliantShine
Speed 60°
Speed 45°
max
Machine Care
Favourite
1
Suitable programme for running at night: it
takes longer, but is extremely quiet.
2 half standard load
7. To cancel the programme, press
approx. 4 seconds.
The programme is cancelled and ends after ap-
prox. 1 minute.
1) Duration [h:min]
2) Energy [kWh]
3) Water [l]
1) 2:25 - 2:30
2) 1,150 - 1,250
3) 10,5 - 13,5
1) 1:40 - 2:40
2) 0,680 - 1,300
3) 7,0 - 15,5
1) 4:55
2) 0,543
3) 9,5
1) 4:00
2) 0,800
3) 10,5
1) 1:55 - 2:00
2) 0,800 - 0,850
3) 14,0 - 16,6
1) 1:29
2) 1,050
3) 11,5
1) 0:35 2
2) 0,710
3) 10,5
1) 2:10
2) 1,350
3) 15,0
1) 0:15 - 0:15
2) 0,050 - 0,050
3) 4,0 - 4,0
for