Download Print this page

Advertisement

Quick Links

Taal: Engels
Handleiding
Merk GYS Lasapparaat CO2 T3
Artikelnummer GY 032958
MSH equipment
Appelmarkt 7
1681 PE Zwaagdijk-Oost
Tel: 0228-561100
Fax: 0228-561112
Mail:
info@msh-equipment.nl
Website: www.msh-equipment.nl

Advertisement

loading
Need help?

Need help?

Do you have a question about the 032958 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for GYS 032958

  • Page 1 Taal: Engels Handleiding Merk GYS Lasapparaat CO2 T3 Artikelnummer GY 032958 MSH equipment Appelmarkt 7 1681 PE Zwaagdijk-Oost Tel: 0228-561100 Fax: 0228-561112 Mail: info@msh-equipment.nl Website: www.msh-equipment.nl...
  • Page 2 M1 GYS AUTO 6-10 / 27-36 T1 GYS AUTO T1 GYS AUTO DV 11-14 / 27-36 T3 GYS AUTO T3 GYS AUTO DV 15-18/ 27-36 19-22 / 27-36 23-26 / 27-36 www.gys.fr 75560 - V5 - 12/03/2014...
  • Page 3 M1 - T1 & T3 GYS AUTO I - M1 & T1 II - T3 Fig 4-B : Fig 4-C :...
  • Page 4 M1 - T1 & T3 GYS AUTO...
  • Page 5 M1 - T1 & T3 GYS AUTO T3 GYS AUTO • Prémonter les vis manuellement sans les bloquer • Pre-install the screws manually without blocking them Vis/Screws M5x12 (x8) Ecrous/Nuts M5x8 (x8) M1 - T1 - T3 GYS AUTO Visser toutes les vis du support bouteilles...
  • Page 6 M1 - T1 & T3 GYS AUTO M5x12 (x4) T3 GYS AUTO (option ref. 032958 / 032972)
  • Page 7: Electricity Supply

    30mA. - The T1 GYS auto, T3 GYS auto, T1 GYS auto DV and T3 GYS auto DV have to be connnected to a 380 V (50Hz) ear- thed power supply with a a circuit breaker 10A and 1 differential 30mA. Do not use an extension cord which has a wire section inferior to 2.5 mm².
  • Page 8 M1 - T1 & T3 GYS AUTO - Contact Tip: Use a contact tip SPECIAL aluminium corresponding to the diameter of the wire. - Contact Tip: Use the specific Aluminium contact tip corresponding to the diameter of the wire. SEMI-AUTOMATIC BRAZING WELDING FOR HIGH-TENSILE STRENGTH STEELS These welding are recommended by car manufacturers to braze-weld high-tensile strength plates with a cuprosilicium CusI3 wire or cuproaluminium CuAl8 wire (Ø...
  • Page 9 M1 - T1 & T3 GYS AUTO «MANUAL» MODE (FIG 5) 1-welding mode choice: - Normal (2T): standard two-stage welding 5- Synergic mode: position the potentiometer (2) in the - Delay: intermittent welding modes for an optimised middle of the «optimal synergic» zone. In this mode, the operating procedure.
  • Page 10 M1 - T1 & T3 GYS AUTO SPOOL GUN (OPTION) Spool gun description and functionning - The spool on gun torch must be installed on the torch T1 connector. - The spool on gun works either in « Manual » mode or either in « Synergic » mode.
  • Page 11 iconeS / SymBolS / ZeichenerKlÄrUng / iconoS / CиMBOЛЫ Ampères - Amps - Ampere - Amperios - Ампер Volt - Volt - Volt - Voltios - Вольт Hertz - Hertz - Hertz - Hertz - Герц Soudage MIG/MAG (MIG: Metal Inert Gas / MAG: Metal Active Gas) - MIG/MAG Welding (MIG: Metal Inert Gas / MAG: Metal Active Gas) - MIG/MAG Schweißen (MIG: Metal Inert Gas/ MAG: Metal Active Gas) - Soldadura MIG/MAG (MIG: Metal Inert Gas / MAG: Metal Active Gas) - Полуавтоматическая...
  • Page 12 iconeS / SymBolS / ZeichenerKlÄrUng / iconoS / CиMBOЛЫ U2: Tensions conventionnelles en charges correspondantes. - U2: conventional voltages in corresponding U2 ...% load. - U2: entsprechende Arbeitsspannung. - U2: Tensiones convencionales en carga. - U2: соответствующие сварочные напряжения*. Appareil conforme aux directives européennes. - The device complies with European Directive. - Gerät entspricht europäischen Richtlinien.
  • Page 13 iconeS / SymBolS / ZeichenerKlÄrUng / iconoS / CиMBOЛЫ Identification polarité négative - Negative pole - Minuspol - Polaridad negativa - отрицательная полярность Terre - Earth ground - Erdung - Tierre - Заземление Ne pas utiliser en zones résidentielles (CEM) - Not for use in residential areas (EMC) - Nicht für die Benutzung in Wohnräumen geeignet.

This manual is also suitable for:

T1 gys autoT1 gys auto dvT3 gys autoT3 gys auto dvM1 gys auto