CAMDEN CX-95S-DH Installation Instructions

Magnetic Door Holders
CX-95S-DH Magnetic Door Holder
INSTALLATION INSTRUCTIONS
THIS PACKAGE INCLUDES:
1 x Door holder
4 x Wall Plugs
6 x M4 Self Tapping Screws

1. GENERAL DESCRIPTION

The Camden CX-95S-DH Magnetic Door Holder is designed for virtually
any remote door release application. The UL-listed Camden Magnetic
Door Holders control the release and closing of commercial and public
area doors, including apartments, schools, hotels, hospitals, and offices.
Fail-safe operation, tri-volt coils, and an adjustable armature plate allow
for easy and flexible installation. Camden magnetic door holders may be
surface or flush mounted, with all mounting hardware included in the kit.

2. SPECIFICATIONS

Operating Voltage 12V
Supply
AC
Current Draw 55mA
Holding Force
Up to 30 lbs.
Mount Options
Surface or Flush mount
Surface mount Magnet:
2-3/4" W x 4-5/8" L x 2-1/2" D
(70mm x 116mm x 62mm)
Flush mount Magnet:
Dimensions 2-3/4" W x 4-5/8" L x 1-3/4" D
(70mm x 116mm x 44mm)
Armature:
2-9/16" W x 2-9/16" L x 2-7/8" D
(65mm x 65mm x 74mm)

4. INSTALLATION

1. Decide on the location for both the Magnetic Door Holder and the
Armature Plate.
2. Select the voltage for the Door Holder by setting the jumpers (two
jumpers for 12VAC/VDC, or one jumper for 24VAC/VDC or 120VAC)
(See Figure 4.3).
Surface Mount Magnetic Door Holder:
3. Use a pencil to mark the position for the mounting holes.
4. Drill holes at the marked positions using a 15/64" drill bit and insert
the provided wall plugs.
5. Align the magnetic door holder back box with the holes and let the
connecting wires pass through the center hole of the back box.
6. Secure the back box using the four M4 self-tapping screws provided in
1 x Armature Plate
1 x Hex Key
1 X Manual
24V
DC AC DC AC
57mA 32mA 34mA 30mA
Up to 35 lbs. Up to 18 lbs.

3. DIMENSIONS

Ø2 1/8"
[55mm]
Ø2 1/8"
[55mm]
2 3/4"
[70mm]
2 3/4"
[70mm]
[116mm]
120V
2 3/4"
DC
[116mm]
[70mm]
-
2 3/4"
4 5/8"
[70mm]
[116mm]
2 3/4"
[70mm]
[116mm]
[116mm]
2 3/4"
[70mm]
the part kit .
7. Connect the wires according to the wiring diagram shown in figure 4.2.
8. Attach the magnetic door holder to the back box using the two M3x6
Phillips head screws provided.
9. Finally, attach the faceplate using the two M3x20 Phillips flat head
4 5/8"
screws.
[116mm]
Flush Mount Magnetic Door Holder
10. Connect the wires according to the wiring diagram as shown in Figure
4.2.
11. Mount the magnetic door holder using the two M3x6 Phillips head
screws provided.
12. Attach the faceplate using two M3x20 Phillips flat head screws.
Ø2 1/8" 2 7/8"
[74mm]
[55mm]
2 7/8"
[74mm]
2 7/8"
[74mm]
Ø2 9/16"
[65mm]
Figure 3.1 Armature Plate
Figure 3.1 Armature Plate
1 3/4"
[44mm]
Figure 3.1 Armature Plate
Figure 3.1 Armature Plate
1 3/4"
[44mm]
4 5/8" 2"
[50mm]
1 3/4"
4 5/8" 2"
[50mm]
[44mm]
3/4"
1"
[18mm]
[26mm]
Figure 3.2 Flush Mount
1" 3/4"
[26mm] [18mm]
Figure 3.2 Flush Mount
Figure 3.2 Flush Mount
2 1/2"
2"
[62mm]
[50mm]
2 1/2"
[62mm]
4 5/8"
3/4"
1"
[18mm]
[26mm]
4 5/8"
Figure 3.2 Flush Mount
Figure 3.3 Surface Mount
Figure 3.3 Surface Mount
2 1/2"
[62mm]
Figure 3.3 Surface Mount
Figure 3.3 Surface Mount
1 7/8"
[47mm]
1 7/8"
[47mm]
1 7/8"
[47mm]
Ø2 1/2"
[65mm]
Ø2 9/16"
2"
[65mm]
[50mm]
2"
[50mm]
2 3/8"
3 1/4"
[84mm] [60mm]
2 3/8" 2"
3 1/4"
[60mm]
[84mm]
[50mm]
3 1/4" 2 3/4"
[70mm]
[84mm]
2 3/4"
[70mm]
4 5/8"
[116mm]
4 5/8"
[116mm]
2 3/4"
[70mm]
Page 1 of 2
2
[6
2 1/
[65m
4
[1