About this Product Thank you for your purchase of Ikelite equipment. Please read this instruction manual completely before attempting to operate or dive with this product. Please visit ikelite.com to register your product to receive information on any updates, notices, or recalls pertaining to your equipment.
Important Notices DO NOT lubricate or remove the battery pack o-ring. » DO NOT use lubricants, cleaners, or any chemical on the » o-ring or battery pack. The battery pack is NOT waterproof when removed from the » strobe front. NEVER use, ship, or travel with a water damaged battery pack.
Contents About this Product Included in the Box Important Notices Getting to Know Your Strobe Setting Up Your Strobe Removing the Battery Pack Charging the Battery Pack Attaching the Battery Pack Using a Diffuser Choosing an Arm System Attaching a Sync Connector Using Your Strobe Turning the Strobe On Checking Battery Level...
Setting Up Your Strobe Removing the Battery Pack The battery pack is NOT waterproof when detached from the » strobe front. Do not remove or lubricate the battery pack o-ring. » 1. Turn the Power Switch to the OFF position and place the strobe face down on a flat surface.
Page 9
To extend the lifetime of the pack, avoid fully discharging the » battery pack. If the battery pack is nearly depleted, we recommend charging » to approximately 50% prior to long-term storage. When storing for extended periods of time, cycle the battery »...
GREEN The charging indicator LED on the front of the charger glows green when the charger is plugged into a power source and when the pack is fully charged. When glowing green the charger is in trickle charge mode. The charging indicator LED glows red when charging the pack. Typical charge time is 4 hours.
7. Flip the toggle lock down and slide in to the locked position. Using a Diffuser The DS232 flashtube and reflector are designed for exceptionally smooth, even coverage without the addition of a diffuser. The optional Dome Diffuser # 4069.2 may be added to increase the spread of the DS232 beam.
Page 12
1. Remove the bulkhead cap. 2. Lightly lubricate the connector o-ring. We recommend using only Ikelite silicone lubricant to eliminate the possibility of swelling due to incompatible compounds. 3. Line up the pins and receptacles and insert the sync cord plug into the bulkhead.
Using Your Strobe Turning the Strobe On The strobe has three ON positions which each affect the function of the flash, video light, and indicator LEDs. Fuel TTL Full Gauge Batt w/Lite Ready Light w/Lite Clockwise one stop from OFF. In this position the LED marked 2 on the Fuel Gauge acts as a visual indicator that the strobe is ready to fire.
Battery level display. After the test sequence is completed the battery level will display for approximately 1-2 seconds. Video light on. Video light power can be adjusted using the srobe’s Exposure Switch. The video light will flash SOS in the SOS/ TTL switch position.
Using the Exposure Switch The strobe has 11 exposure switch positions which affect either the output of the flash or video light, depending on which ON position the strobe power switch is in. Fuel TTL Full Gauge Batt w/Lite Ready Light w/Lite SOS / TTL •...
Positioning the Strobe • Use the built-in video light to make sure your strobe is positioned in the correct location in relation to your camera frame. • Adjust the angle of the strobe as the distance between you and your subject changes. Firing the Strobe •...
Some frames may be missed at extremely high speeds and/or » when shooting above half power. Maintenance Post-Dive 1. Rinse your strobe and camera system in fresh water. Do not remove the battery pack or sync cord prior to rinsing. 2.
6. Attach the battery pack cover to the battery pack. 7. Store the strobe front and battery pack in a cool, dry place. Learning about Underwater Photography Visit http://www.ikelite.com/photoschool or scan the QR code: Troubleshooting Water enters the battery pack.
Page 19
• Adjust aperture (larger), shutter speed (slower), or ISO (lower) setting. • Move strobe(s) closer to your subject and check aiming. Strobe will not fire when using sync cord. • Make sure the strobe is turned on. • Try a different sync cord. •...
(1) year from the original date of purchase. Defective products should be returned to Ikelite postage paid. Ikelite will, at its sole discretion, repair or replace such products, and will return to customer postage paid.
If you have any questions about your product or need advice on getting the images you want, please get in touch with us and we’ll do everything we can to help you capture your unique perspective. Ikelite Underwater Systems 50 W 33rd St Indianapolis, IN 46208 USA +1 (317) 923-4523 ikelite@ikelite.com...